lkml.org 
[lkml]   [2020]   [Jun]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] xhci: Poll for U0 after disabling USB2 LPM
From
Date
Hi Mathias,

> On Jun 9, 2020, at 18:15, Kai-Heng Feng <kai.heng.feng@canonical.com> wrote:
>
>
>
>> On Jun 8, 2020, at 19:21, Mathias Nyman <mathias.nyman@linux.intel.com> wrote:
>>
>> On 20.5.2020 13.18, Kai-Heng Feng wrote:
>>> USB2 devices with LPM enabled may interrupt the system suspend:
>>> [ 932.510475] usb 1-7: usb suspend, wakeup 0
>>> [ 932.510549] hub 1-0:1.0: hub_suspend
>>> [ 932.510581] usb usb1: bus suspend, wakeup 0
>>> [ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
>>> [ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
>>> ..
>>> [ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
>>
>> 400e03 = Connected, Enabled, U0 with port ink state change flag (PLC) set.
>>
>>> ..
>>> [ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
>>> [ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
>>> [ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
>>>
>>> During system suspend, USB core will let HC suspends the device if it
>>> doesn't have remote wakeup enabled and doesn't have any children.
>>> However, from the log above we can see that the usb 1-7 doesn't get bus
>>> suspended due to not in U0. After a while the port finished U2 -> U0
>>> transition, interrupts the suspend process.
>>
>> In USB2 HW link PM the PLC flag should not be set in U2Exit -> U0 transitions.
>> Only case we should see a port change event is U2Entry -> U0 due to STALL or
>> error/timeout. (see xhci 4.23.5.1.1.1)
>>
>>>
>>> The observation is that after disabling LPM, port doesn't transit to U0
>>> immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
>>> maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
>>> the affected device is advertised as 400us, which is still not enough
>>> based on my testing result.
>>>
>>> So let's use the maximum permitted latency, 10000, to poll for U0
>>> status to solve the issue.
>>
>> I don't recall all details, but it could be that disabling LPM before suspend
>> is unnecessary.
>> At least xhci should be able to set a port to U3 from U1 and U2 (see xhci 4.15.1)
>> so that is one change that could be done to xhci_bus_suspend()
>
> Yes, put the device to U3 directly does the trick.

As discussed, will you pick this series over the v2?
Or is there anything I should improve for this one?

Kai-Heng

>
>>
>> Also just noticed that we are not really checking L1S field in PORTPMSC register,
>> this should tell if there was an issue with USB2 lpm state transitions, and
>> perhaps we should disable lpm for that device.
>>
>> Does the L1S field show anything unuaual in your case?
>> That could explain the port event with the PLC bit set.
>
> diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
> index 2c255d0620b0..a2099d42e490 100644
> --- a/drivers/usb/host/xhci-ring.c
> +++ b/drivers/usb/host/xhci-ring.c
> @@ -1592,7 +1592,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
> {
> struct usb_hcd *hcd;
> u32 port_id;
> - u32 portsc, cmd_reg;
> + u32 portsc, portpmsc, cmd_reg;
> int max_ports;
> int slot_id;
> unsigned int hcd_portnum;
> @@ -1634,9 +1634,10 @@ static void handle_port_status(struct xhci_hcd *xhci,
> bus_state = &port->rhub->bus_state;
> hcd_portnum = port->hcd_portnum;
> portsc = readl(port->addr);
> + portpmsc = readl(port->addr + PORTPMSC);
>
> - xhci_dbg(xhci, "Port change event, %d-%d, id %d, portsc: 0x%x\n",
> - hcd->self.busnum, hcd_portnum + 1, port_id, portsc);
> + xhci_dbg(xhci, "Port change event, %d-%d, id %d, portsc: 0x%x, portpmsc 0x%0x\n",
> + hcd->self.busnum, hcd_portnum + 1, port_id, portsc, portpmsc);
>
> trace_xhci_handle_port_status(hcd_portnum, portsc);
>
> [ 685.460054] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03, portpmsc 0x1
> [ 685.460062] xhci_hcd 0000:00:14.0: resume root hub
> [ 685.460079] xhci_hcd 0000:00:14.0: handle_port_status: starting port polling.
> [ 685.460094] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping port polling.
> [ 685.521685] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
> [ 685.521695] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
> [ 685.521699] PM: Device 0000:00:14.0 failed to suspend async: error -16
>
> So after disabling LPM, it takes a long time to complete L1 transition, before transitioning to L0.
>
> Kai-Heng
>
>>
>> I think we can avoid a readl_poll_timeout() solution in this case.
>>
>> -Mathias

\
 
 \ /
  Last update: 2020-06-19 16:20    [W:0.069 / U:0.492 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site