lkml.org 
[lkml]   [2020]   [Jun]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 5.4 048/261] batman-adv: Revert "disable ethtool link speed detection when auto negotiation off"
Date
From: Sven Eckelmann <sven@narfation.org>

[ Upstream commit 9ad346c90509ebd983f60da7d082f261ad329507 ]

The commit 8c46fcd78308 ("batman-adv: disable ethtool link speed detection
when auto negotiation off") disabled the usage of ethtool's link_ksetting
when auto negotation was enabled due to invalid values when used with
tun/tap virtual net_devices. According to the patch, automatic measurements
should be used for these kind of interfaces.

But there are major flaws with this argumentation:

* automatic measurements are not implemented
* auto negotiation has nothing to do with the validity of the retrieved
values

The first point has to be fixed by a longer patch series. The "validity"
part of the second point must be addressed in the same patch series by
dropping the usage of ethtool's link_ksetting (thus always doing automatic
measurements over ethernet).

Drop the patch again to have more default values for various net_device
types/configurations. The user can still overwrite them using the
batadv_hardif's BATADV_ATTR_THROUGHPUT_OVERRIDE.

Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/batman-adv/bat_v_elp.c | 15 +--------------
1 file changed, 1 insertion(+), 14 deletions(-)

diff --git a/net/batman-adv/bat_v_elp.c b/net/batman-adv/bat_v_elp.c
index 2614a9caee00..a39af0eefad3 100644
--- a/net/batman-adv/bat_v_elp.c
+++ b/net/batman-adv/bat_v_elp.c
@@ -120,20 +120,7 @@ static u32 batadv_v_elp_get_throughput(struct batadv_hardif_neigh_node *neigh)
rtnl_lock();
ret = __ethtool_get_link_ksettings(hard_iface->net_dev, &link_settings);
rtnl_unlock();
-
- /* Virtual interface drivers such as tun / tap interfaces, VLAN, etc
- * tend to initialize the interface throughput with some value for the
- * sake of having a throughput number to export via ethtool. This
- * exported throughput leaves batman-adv to conclude the interface
- * throughput is genuine (reflecting reality), thus no measurements
- * are necessary.
- *
- * Based on the observation that those interface types also tend to set
- * the link auto-negotiation to 'off', batman-adv shall check this
- * setting to differentiate between genuine link throughput information
- * and placeholders installed by virtual interfaces.
- */
- if (ret == 0 && link_settings.base.autoneg == AUTONEG_ENABLE) {
+ if (ret == 0) {
/* link characteristics might change over time */
if (link_settings.base.duplex == DUPLEX_FULL)
hard_iface->bat_v.flags |= BATADV_FULL_DUPLEX;
--
2.25.1


\
 
 \ /
  Last update: 2020-06-19 18:10    [W:1.413 / U:0.320 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site