lkml.org 
[lkml]   [2020]   [Jun]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 3/4] nvmem: qfprom: Add fuse blowing support
From
Date
On 6/17/2020 8:51 AM, Douglas Anderson wrote:
> From: Ravi Kumar Bokka <rbokka@codeaurora.org>
>
> This patch adds support for blowing fuses to the qfprom driver if the
> required properties are defined in the device tree.
>
> Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
> ---
> Please double-check that I got the major/minor version logic right
> here. I don't have documentation for this, but Srinivas mentioned
> that it was at address 0x6000 and I happened to find an "8" and a "7"
> on sc7180 so I assumed that was the major and minor version.
>
> Changes in v3:
> - Don't provide "reset" value for things; just save/restore.
> - Use the major/minor version read from 0x6000.
> - Reading should still read "corrected", not "raw".
> - Added a sysfs knob to allow you to read "raw" instead of "corrected"
> - Simplified the SoC data structure.
> - No need for quite so many levels of abstraction for clocks/regulator.
> - Don't set regulator voltage. Rely on device tree to make sure it's right.
> - Properly undo things in the case of failure.
> - Don't just keep enabling the regulator over and over again.
> - Enable / disable the clock each time
> - Polling every 100 us but timing out in 10 us didn't make sense; swap.
> - No reason for 100 us to be SoC specific.
> - No need for reg-names.
> - We shouldn't be creating two separate nvmem devices.
>
> drivers/nvmem/qfprom.c | 314 +++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 303 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/nvmem/qfprom.c b/drivers/nvmem/qfprom.c
> index 8a91717600be..486202860f84 100644
> --- a/drivers/nvmem/qfprom.c
> +++ b/drivers/nvmem/qfprom.c
> @@ -3,57 +3,349 @@
> * Copyright (C) 2015 Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> */
>
> +#include <linux/clk.h>
> #include <linux/device.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/mod_devicetable.h>
> -#include <linux/io.h>
> #include <linux/nvmem-provider.h>
> #include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +
> +/* Blow timer clock frequency in Mhz */
> +#define QFPROM_BLOW_TIMER_OFFSET 0x03c
> +
> +/* Amount of time required to hold charge to blow fuse in micro-seconds */
> +#define QFPROM_FUSE_BLOW_POLL_US 10
> +#define QFPROM_FUSE_BLOW_TIMEOUT_US 100
> +
> +#define QFPROM_BLOW_STATUS_OFFSET 0x048
> +#define QFPROM_BLOW_STATUS_BUSY 0x1
> +#define QFPROM_BLOW_STATUS_READY 0x0
> +
> +#define QFPROM_ACCEL_OFFSET 0x044
> +
> +#define QFPROM_VERSION_OFFSET 0x0
> +#define QFPROM_MAJOR_VERSION_SHIFT 28
> +#define QFPROM_MAJOR_VERSION_MASK 0xf
> +#define QFPROM_MINOR_VERSION_SHIFT 16
> +#define QFPROM_MINOR_VERSION_MASK 0xf

Minor looks wrong. Documentation says bits 27:16 are the minor version,
and bits 15:0 are step. I think your minor mask needs to be 0xfff.

--
Jeffrey Hugo
Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.

\
 
 \ /
  Last update: 2020-06-17 17:04    [W:0.162 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site