lkml.org 
[lkml]   [2020]   [Jun]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/2] spi: introduce fallback to pio
Date
Add fallback to pio mode in case dma transfer failed with error status
SPI_TRANS_FAIL_NO_START.
If spi client driver want to enable this feature please set xfer->error in
the proper place such as dmaengine_prep_slave_sg() failure detect(but no
any data put into spi bus yet). Besides, add master->fallback checking in
its can_dma() so that spi core could switch to pio next time. Please refer
to spi-imx.c.

Signed-off-by: Robin Gong <yibin.gong@nxp.com>
---
drivers/spi/spi.c | 12 ++++++++++++
include/linux/spi/spi.h | 7 +++++++
2 files changed, 19 insertions(+)

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 8158e28..6fa5659 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -982,6 +982,8 @@ static int __spi_unmap_msg(struct spi_controller *ctlr, struct spi_message *msg)
spi_unmap_buf(ctlr, tx_dev, &xfer->tx_sg, DMA_TO_DEVICE);
}

+ ctlr->cur_msg_mapped = false;
+
return 0;
}
#else /* !CONFIG_HAS_DMA */
@@ -1234,8 +1236,17 @@ static int spi_transfer_one_message(struct spi_controller *ctlr,
if (xfer->tx_buf || xfer->rx_buf) {
reinit_completion(&ctlr->xfer_completion);

+fallback_pio:
ret = ctlr->transfer_one(ctlr, msg->spi, xfer);
if (ret < 0) {
+ if (ctlr->cur_msg_mapped &&
+ (xfer->error & SPI_TRANS_FAIL_NO_START)) {
+ __spi_unmap_msg(ctlr, msg);
+ ctlr->fallback = true;
+ xfer->error &= ~SPI_TRANS_FAIL_NO_START;
+ goto fallback_pio;
+ }
+
SPI_STATISTICS_INCREMENT_FIELD(statm,
errors);
SPI_STATISTICS_INCREMENT_FIELD(stats,
@@ -1693,6 +1704,7 @@ void spi_finalize_current_message(struct spi_controller *ctlr)
spin_lock_irqsave(&ctlr->queue_lock, flags);
ctlr->cur_msg = NULL;
ctlr->cur_msg_prepared = false;
+ ctlr->fallback = false;
kthread_queue_work(&ctlr->kworker, &ctlr->pump_messages);
spin_unlock_irqrestore(&ctlr->queue_lock, flags);

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index aac57b5..b4917df 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -447,6 +447,8 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
* If the driver does not set this, the SPI core takes the snapshot as
* close to the driver hand-over as possible.
* @irq_flags: Interrupt enable state during PTP system timestamping
+ * @fallback: fallback to pio if dma transfer return failure with
+ * SPI_TRANS_FAIL_NO_START.
*
* Each SPI controller can communicate with one or more @spi_device
* children. These make a small bus, sharing MOSI, MISO and SCK signals
@@ -602,6 +604,7 @@ struct spi_controller {
bool auto_runtime_pm;
bool cur_msg_prepared;
bool cur_msg_mapped;
+ bool fallback;
struct completion xfer_completion;
size_t max_dma_len;

@@ -847,6 +850,7 @@ extern void spi_res_release(struct spi_controller *ctlr,
* back unset and they need the better resolution.
* @timestamped_post: See above. The reason why both exist is that these
* booleans are also used to keep state in the core SPI logic.
+ * @error: Error status logged by spi controller driver.
*
* SPI transfers always write the same number of bytes as they read.
* Protocol drivers should always provide @rx_buf and/or @tx_buf.
@@ -940,6 +944,9 @@ struct spi_transfer {
bool timestamped;

struct list_head transfer_list;
+
+#define SPI_TRANS_FAIL_NO_START BIT(0)
+ u16 error;
};

/**
--
2.7.4
\
 
 \ /
  Last update: 2020-06-16 16:42    [W:0.058 / U:0.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site