lkml.org 
[lkml]   [2020]   [Jun]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] ARM: dts: orange-pi-zero-plus2: enable USB OTG port
Hi Diego,

On Thu, May 28, 2020 at 10:47:11PM +0200, Diego Rondini wrote:
> Enable support for USB OTG port on Orange Pi Zero Plus 2 (both H3 and H5
> variants). As, according to the board schematics, the USB OTG port cannot
> provide power to external devices, we set dr_mode to peripheral.
>
> Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>

Sorry for the time it took to review it. I initially thought it was ok
and wanted to wait until -rc1 was out to apply it, but...

> ---
> .../boot/dts/sun8i-h3-orangepi-zero-plus2.dts | 23 +++++++++++++++++++
> .../sun50i-h5-orangepi-zero-plus2.dts | 23 +++++++++++++++++++
> 2 files changed, 46 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
> index b8f46e2802fd3..4376767699a47 100644
> --- a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
> @@ -137,3 +137,26 @@ &uart0 {
> pinctrl-0 = <&uart0_pa_pins>;
> status = "okay";
> };
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + /*
> + * According to schematics CN1 MicroUSB port can be used to take
> + * external 5V to power up the board VBUS. On the contrary CN1 MicroUSB
> + * port cannot provide power externally even if the board is powered
> + * via GPIO pins. It thus makes sense to force peripheral mode.
> + */
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};

Nodes should be ordered alphabetically here.

> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
> index c95a68541309c..d8192a7483e9e 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
> @@ -103,3 +103,26 @@ &uart1 {
> pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> status = "okay";
> };
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + /*
> + * According to schematics CN1 MicroUSB port can be used to take
> + * external 5V to power up the board VBUS. On the contrary CN1 MicroUSB
> + * port cannot provide power externally even if the board is powered
> + * via GPIO pins. It thus makes sense to force peripheral mode.
> + */
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};

And here too.

Sorry for not spotting this earlier.

Maxime
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-06-15 10:13    [W:0.496 / U:0.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site