lkml.org 
[lkml]   [2020]   [Jun]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] ARM: exynos: update l2c_aux_mask to fix alert message
From
Date
On 02/04/2020 14:11, Russell King - ARM Linux admin wrote:
> On Thu, Apr 02, 2020 at 02:03:52PM +0100, Russell King - ARM Linux admin wrote:
>> On Thu, Apr 02, 2020 at 01:13:24PM +0100, Guillaume Tucker wrote:
>>> On 01/04/2020 17:31, Russell King - ARM Linux admin wrote:
>>>> On Wed, Apr 01, 2020 at 05:08:03PM +0100, Guillaume Tucker wrote:
>>>>> Allow setting the number of cycles for RAM reads in the pl310 cache
>>>>> controller L2 auxiliary control register mask (bits 0-2) since it
>>>>> needs to be changed in software. This only affects exynos4210 and
>>>>> exynos4412 as they use the pl310 cache controller.
>>>>>
>>>>> With the mask used until now, the following warnings were generated,
>>>>> the 2nd one being a pr_alert():
>>>>>
>>>>> L2C: platform modifies aux control register: 0x02070000 -> 0x3e470001
>>>>> L2C: platform provided aux values permit register corruption.
>>>>>
>>>>> This latency cycles value has always been set in software in spite of
>>>>> the warnings. Keep it this way but clear the alert message about
>>>>> register corruption to acknowledge it is a valid thing to do.
>>>>
>>>> This is telling you that you are doing something you should not be
>>>> doing. The L2C controller should be configured by board firmware
>>>> first and foremost, because if, for example, u-boot makes use of the
>>>> L2 cache, or any other pre-main kernel code (in other words,
>>>> decompressor) the setup of the L2 controller will be wrong.
>>>>
>>>> So, NAK.
>>>
>>> OK thanks, I guess I misinterpreted the meaning of the error
>>> message. It's really saying that the register value was not the
>>> right one before the kernel tried to change it. Next step for me
>>> is to look into U-Boot.
>>
>> The message "L2C: platform provided aux values permit register
>> corruption." means that bits are set in both the mask and the value
>> fields. Since the new value is calculated as:
>>
>> old = register value;
>> new = old & mask;
>> new |= val;
>>
>> If bits are set in both "mask" and "val" for a multi-bit field, the
>> value ending up in the field may not be what is intended. Consider
>> a 5-bit field set initially to 10101, and the requested value is
>> 01000 with a mask of 11111. What you end up with is not 01000, but
>> 11101. Hence, register corruption. It is not possible to easily
>> tell whether the mask and values refer to a multi-bit field or not,
>> so the mere fact that bits are set in both issues the alert.
>>
>> The message "L2C: platform modifies aux control register ..." means
>> that you're trying to modify the value of the auxiliary control
>> register, which brings with it the problems I stated in my previous
>> email; platform configuration of the L2C must be done by firmware and
>> not the kernel for the reasons I've set out.
>
> Actually, looking at the values there:
>
> .l2c_aux_val = 0x3c400001,
> - .l2c_aux_mask = 0xc20fffff,
> + .l2c_aux_mask = 0xc20ffff8,
>
> Bit 0 is L310_AUX_CTRL_FULL_LINE_ZERO feature bit, which platforms have
> no business fiddling with - it is a Cortex-A9/L2C310 specific feature
> that needs both ends to be configured correctly to work. The L2C code
> knows this and will deal with it. So, .l2c_aux_val should drop setting
> bit 0.

Ack, I've just sent a patch to fix that:

ARM: exynos: clear L310_AUX_CTRL_FULL_LINE_ZERO in default l2c_aux_val

Sorry about the confusion in my first patch, I got mislead with
the TRM of an earlier revision of the L2C-310 when these bits
were used to set the RAM data read latency. So this all makes
sense to me now with the matching documentation for the hardware.

> It's also setting L310_AUX_CTRL_NS_LOCKDOWN, which the kernel already
> deals with - this bit should be dropped as well.

OK I'll take a look at that and send a separate patch.

Presumably this bit should also be added to the mask to report an
error if the kernel is changing it?

> It's clearing L310_AUX_CTRL_CACHE_REPLACE_RR - this should be setup by
> firmware.

As far as I can tell, L310_AUX_CTRL_CACHE_REPLACE_RR is bit 25
i.e. 0x02000000, which is set in hardware by default and is not
changed by the kernel:

L2C: platform modifies aux control register: 0x02070000 -> 0x3e470001

Also this bit is already in the mask, and there is no error about
register corruption any more with the patch I sent today.

> For the prefetching, I thought there were DT properties for that.
> Please look at that, and see whether you can eliminate most of the
> .l2c_aux_val field set bits, and the .l2c_aux_mask clear bits.

Ack, it's handled by l2c310_of_parse(). I'll take a look and see
if I can make another patch for that.

Thanks,
Guillaume

\
 
 \ /
  Last update: 2020-06-12 16:23    [W:0.234 / U:0.496 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site