lkml.org 
[lkml]   [2020]   [Jun]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH v1 10/18] dt-bindings: tegra: Document VI and CSI port nodes
Hi Sowjanya,

Thanks for the patchset.

On Tue, Jun 09, 2020 at 11:02:32PM -0700, Sowjanya Komatineni wrote:
> This patch documents Tegra VI and CSI port and endpoint nodes along
> with the other required properties.
>
> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
> ---
> .../display/tegra/nvidia,tegra20-host1x.txt | 87 ++++++++++++++++++++++
> 1 file changed, 87 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
> index 4731921..f70a838 100644
> --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
> +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
> @@ -65,6 +65,48 @@ of the following host1x client modules:
> - power-domains: Must include sor powergate node as csicil is in
> SOR partition.
>
> + Optional properties for csi node:

What hardware does the csi node represent? A CSI-2 receiver? Something
else?

If you have two connections, you need two ports. The example isn't quite
clear on this; it would appear to represent a single physical interface.

> +
> + - channel nodes: Max upto 6 channels/streams are supported with each CSI
> + brick can as either x4 or x2 based on hw connectivity to sensor.
> +
> + Required properties:
> + - reg: channel/stream index
> + - nvidia,mipi-calibrate: Should contain a phandle and a specifier
> + specifying which pads are used by this CSI port and need to be
> + calibrated. See also ../display/tegra/nvidia,tegra114-mipi.txt.
> +
> + - port: CSI port node and its endpoint nodes as per device graph
> + bindings defined in Documentation/devicetree/bindings/graph.txt.
> + Required properties:

You have both properties and nodes here. Same for the above (port is a
node).

> + - reg: csi port index based on hw csi lanes connectivity to the
> + sensor.
> + - bus-width: number of lanes used by this port. Supported lanes
> + are 1/2/4.

bus-width belongs to the endpoint. Note that this is for parallel busses
only. If you need the number of lanes, the property is called data-lanes.

> + - endpoint@0: sink node
> + Required properties:
> + - reg: endpoint id. This is used to retrieve pad for creating
> + media link
> + - remote-endpoint: phandle to sensor endpoint
> + - endpoint@1: source node
> + - reg: endpoint id. This is used to retrieve pad for creating
> + media link
> + - remote-endpoint: phandle to vi port endpoint
> +
> + Optional properties for vi node:
> + - ports: Video port nodes and endpoint nodes as per device graph bindings
> + defined in Documentation/devicetree/bindings/graph.txt
> + Max 6 ports are supported and each port should have one endpoint node.
> +
> + Required properties:
> + - port: VI port node and its sink endpoint node
> + Required properties:
> + - reg: should match port index
> + - endpoint@0: sink node
> + Required properties:
> + - reg: endpoint id must be 0
> + - remote-endpoint: phandle to CSI endpoint node.
> +
> - epp: encoder pre-processor
>
> Required properties:
> @@ -340,6 +382,22 @@ Example:
>
> ranges = <0x0 0x0 0x54080000 0x2000>;
>
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + imx219_vi_in0: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&imx219_csi_out0>;
> + };
> + };
> + };
> +
> csi@838 {
> compatible = "nvidia,tegra210-csi";
> reg = <0x838 0x1300>;
> @@ -362,6 +420,35 @@ Example:
> <&tegra_car TEGRA210_CLK_CSI_TPG>;
> clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
> power-domains = <&pd_sor>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@0 {
> + reg = <0>;
> + nvidia,mipi-calibrate = <&mipi 0x001>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + bus-width = <2>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + imx219_csi_in0: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&imx219_out0>;
> + };
> +
> + imx219_csi_out0: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&imx219_vi_in0>;
> + };
> + };
> + };
> };
> };
>

--
Kind regards,

Sakari Ailus

\
 
 \ /
  Last update: 2020-06-10 13:24    [W:0.154 / U:1.540 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site