lkml.org 
[lkml]   [2020]   [May]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 5/5] drm/panel: add panel driver for Ilitek ili9341 panels
Hi sam, all,

i'm not sure you had receive this mail , as gmail's html encoded
messages blocked by linux arm kernel mailing list.
so, resent it in plain text again. with my name "dillon: " at left

sorry for trouble.

dillon

best regards

dillon min <dillon.minfei@gmail.com> 于2020年5月8日周五 下午6:13写道:
>
Hi Sam,

Thanks for your comments, i will rework this panel driver after
l3gd20 patch submission.

> Sam Ravnborg <sam@ravnborg.org> 于2020年5月8日周五 下午5:02写道:
>>
>> Hi Dillon.
>>
>> Patch submissions starts to look fine.
>>
>> On Fri, May 08, 2020 at 12:13:14PM +0800, dillon.minfei@gmail.com wrote:
>> > From: dillon min <dillon.minfei@gmail.com>
>> >
>> > This is a driver for 320x240 TFT panels, accepting a rgb input
>> > streams that get adapted and scaled to the panel.
> This driver is, I suppose, prepared to be a driver for ILI9341 based
> panles, and as such not for a fixed resolution.
> I expect (hope) we in the future will see more panels added.
>
dillon:
As i checked ili9341 datasheets, this panel just support 240x320
resolution only. if i'm wrong , please correct me. thanks
https://cdn-shop.adafruit.com/datasheets/ILI9341.pdf

This panel can support 9 different kinds of interface , "3/4-line
Serial Interface" have been supported by tiny/ili9341.c. i was
verified it
but the performance on stm32f4 is very low.

currently, i just have stm32f429-disco in hands, with 18-bit parallel
rgb bus connected on this board. reference to panel-ilitek-ili9322 and
panel-ilitek-ili9881 driver, i have some plan to rewrite this driver.

1 add your below comments in.
2 use dc-gpio, reset-gpio, rgb-interface-bits from dts to config panel
interface.
3 drop regmap, porting drm_mipi_dbi's mipi_dbi_command to config panel
paramter. like tiny/ili9341.c
4 support rgb-16, rgb-18 interface.
5 use optional regulator or power gpio to control panel's power, as
panel power is always on for my board, so i can't test this part.
could i add the code which can't be tested?
6 support rotation in panel config (currently , i rotate the screen by
kernel cmdline paramter)

if you have any other common panel configuration should be add ,
please inform me.

thanks.
>>
>>
>> Some things to fix, see comments in the follwoing.
>>
>> Sam
>>
>> >
>> > Signed-off-by: dillon min <dillon.minfei@gmail.com>
>> > ---
>> > drivers/gpu/drm/panel/Kconfig | 8 +
>> > drivers/gpu/drm/panel/Makefile | 1 +
>> > drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 561 +++++++++++++++++++++++++++
>> > 3 files changed, 570 insertions(+)
>> > create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c
>> >
>> > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
>> > index a1723c1..e42692c 100644
>> > --- a/drivers/gpu/drm/panel/Kconfig
>> > +++ b/drivers/gpu/drm/panel/Kconfig
>> > @@ -95,6 +95,14 @@ config DRM_PANEL_ILITEK_IL9322
>> > Say Y here if you want to enable support for Ilitek IL9322
>> > QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
>> >
>> > +config DRM_PANEL_ILITEK_IL9341
>> ILI9341 - so the config name matches the name of the driver IC.
>>
>> > + tristate "Ilitek ILI9341 240x320 QVGA panels"
>> > + depends on OF && SPI
>> > + select REGMAP
>> > + help
>> > + Say Y here if you want to enable support for Ilitek IL9341
>> > + QVGA (240x320) RGB panels.
>> See comment to the changelog, the driver is more generic - I assume.
>> So the wording here can be improved to express this.
>>

dillon: Add support RGB 16bits and RGB 18bits bus only ?

>>
>> > +
>> > config DRM_PANEL_ILITEK_ILI9881C
>> > tristate "Ilitek ILI9881C-based panels"
>> > depends on OF
>> > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
>> > index 96a883c..d123543 100644
>> > --- a/drivers/gpu/drm/panel/Makefile
>> > +++ b/drivers/gpu/drm/panel/Makefile
>> > @@ -8,6 +8,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
>> > obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
>> > obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
>> > obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
>> > +obj-$(CONFIG_DRM_PANEL_ILITEK_IL9341) += panel-ilitek-ili9341.o
>> > obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
>> > obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
>> > obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
>> > diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
>> > new file mode 100644
>> > index 0000000..ec22d80
>> > --- /dev/null
>> > +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
>> > @@ -0,0 +1,561 @@
>> > +// SPDX-License-Identifier: GPL-2.0-only
>> > +/*
>> > + * Ilitek ILI9341 TFT LCD drm_panel driver.
>> > + *
>> > + * This panel can be configured to support:
>> > + * - 16-bit parallel RGB interface
>> The interface to ILI9341 is SPI, and the interface between the ILI9341
>> and the panel is more of an itnernal thing. Or did I get this worng?
>>

dillon: SPI is for register configuration. RGB parallel for data transfer

>
>> > + *
>> > + * Copyright (C) 2020 Dillon Min <dillon.minfei@gmail.com>
>> > + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c
>> > + */
>> > +
>> > +#include <linux/bitops.h>
>> > +#include <linux/gpio/consumer.h>
>> > +#include <linux/module.h>
>> > +#include <linux/of_device.h>
>> > +#include <linux/regmap.h>
>> > +#include <linux/regulator/consumer.h>
>> > +#include <linux/spi/spi.h>
>> > +
>> > +#include <video/mipi_display.h>
>> > +#include <video/of_videomode.h>
>> > +#include <video/videomode.h>
>> > +
>> > +#include <drm/drm_modes.h>
>> > +#include <drm/drm_panel.h>
>> > +#include <drm/drm_print.h>
>> > +
>> > +#define DEFAULT_SPI_SPEED 10000000
>> > +
>>
>> Please use same case for hex numbers in the driver.
>> My personal preferences is lower-case.
>>

dillon:
in next patch, spi speed will be configured by dts, not hardcode here.
below register address will change to lower-case hex numbers.

>
>>
>> > +#define ILI9341_SLEEP_OUT 0x11 /* Sleep out register */
>> > +#define ILI9341_GAMMA 0x26 /* Gamma register */
>> > +#define ILI9341_DISPLAY_OFF 0x28 /* Display off register */
>> > +#define ILI9341_DISPLAY_ON 0x29 /* Display on register */
>> > +#define ILI9341_COLUMN_ADDR 0x2A /* Colomn address register */
>> > +#define ILI9341_PAGE_ADDR 0x2B /* Page address register */
>> > +#define ILI9341_GRAM 0x2C /* GRAM register */
>> > +#define ILI9341_MAC 0x36 /* Memory Access Control register*/
>> > +#define ILI9341_PIXEL_FORMAT 0x3A /* Pixel Format register */
>> > +#define ILI9341_WDB 0x51 /* Write Brightness Display
>> > + * register
>> > + */
>> > +#define ILI9341_WCD 0x53 /* Write Control Display
>> > + * register
>> > + */
>> > +#define ILI9341_RGB_INTERFACE 0xB0 /* RGB Interface Signal Control */
>> > +#define ILI9341_FRC 0xB1 /* Frame Rate Control register */
>> > +#define ILI9341_BPC 0xB5 /* Blanking Porch Control
>> > + * register
>> > + */
>> > +#define ILI9341_DFC 0xB6 /* Display Function Control
>> > + * register
>> > + */
>> > +#define ILI9341_POWER1 0xC0 /* Power Control 1 register */
>> > +#define ILI9341_POWER2 0xC1 /* Power Control 2 register */
>> > +#define ILI9341_VCOM1 0xC5 /* VCOM Control 1 register */
>> > +#define ILI9341_VCOM2 0xC7 /* VCOM Control 2 register */
>> > +#define ILI9341_POWERA 0xCB /* Power control A register */
>> > +#define ILI9341_POWERB 0xCF /* Power control B register */
>> > +#define ILI9341_PGAMMA 0xE0 /* Positive Gamma Correction
>> > + * register
>> > + */
>> > +#define ILI9341_NGAMMA 0xE1 /* Negative Gamma Correction
>> > + * register
>> > + */
>> > +#define ILI9341_DTCA 0xE8 /* Driver timing control A */
>> > +#define ILI9341_DTCB 0xEA /* Driver timing control B */
>> > +#define ILI9341_POWER_SEQ 0xED /* Power on sequence register */
>> > +#define ILI9341_3GAMMA_EN 0xF2 /* 3 Gamma enable register */
>> > +#define ILI9341_INTERFACE 0xF6 /* Interface control register */
>> > +#define ILI9341_PRC 0xF7 /* Pump ratio control register */
>> > +
>>
>> All the following should be const.
>

dillon: ok

>
>>
>> Can any of the below be replaces by DEFINED constants?
>> > +static u8 ili9341_cmd0[] = {0xc3, 0x08, 0x50};
>> > +static u8 ili9341_powerb[] = {0x00, 0xc1, 0x30};
>> > +static u8 ili9341_power_seq[] = {0x64, 0x03, 0x12, 0x81};
>> > +static u8 ili9341_dtca[] = {0x85, 0x00, 0x78};
>> > +static u8 ili9341_powera[] = {0x39, 0x2c, 0x00, 0x34, 0x02};
>> > +static u8 ili9341_prc[] = {0x20};
>> > +static u8 ili9341_dtcb[] = {0x00, 0x00};
>> > +static u8 ili9341_frc[] = {0x00, 0x1b};
>> > +static u8 ili9341_dfc1[] = {0x0a, 0xa2};
>> > +static u8 ili9341_power1[] = {0x10};
>> > +static u8 ili9341_power2[] = {0x10};
>> > +static u8 ili9341_vcom1[] = {0x45, 0x15};
>> > +static u8 ili9341_vcom2[] = {0x90};
>> > +static u8 ili9341_mac[] = {0xc8};
>> > +static u8 ili9341_gamma_en[] = {0x00};
>> > +static u8 ili9341_rgb_intr[] = {0xc2};
>> > +static u8 ili9341_dfc2[] = {0x0a, 0xa7, 0x27, 0x04};
>> > +static u8 ili9341_column_addr[] = {0x00, 0x00, 0x00, 0xef};
>> > +static u8 ili9341_page_addr[] = {0x00, 0x00, 0x01, 0x3f};
>> > +static u8 ili9341_intr[] = {0x01, 0x00, 0x06};
>> > +static u8 ili9341_gamma[] = {0x01};
>> > +static u8 ili9341_pgamma[] = {0x0f, 0x29, 0x24, 0x0c, 0x0e, 0x09, 0x4e, 0x78,
>> > + 0x3c, 0x09, 0x13, 0x05, 0x17, 0x11, 0x00};
>> > +static u8 ili9341_ngamma[] = {0x00, 0x16, 0x1b, 0x04, 0x11, 0x07, 0x31, 0x33,
>> > + 0x42, 0x05, 0x0c, 0x0a, 0x28, 0x2f, 0x0f};
>> > +
>> > +/**
>> > + * enum ili9341_input - the format of the incoming signal to the panel
>> > + *
>> > + * The panel can be connected to various input streams and four of them can
>> > + * be selected by electronic straps on the display. However it is possible
>> > + * to select another mode or override the electronic default with this
>> > + * setting.
>> > + */
>> > +enum ili9341_input {
>> > + ILI9341_INPUT_PRGB_THROUGH = 0x0,
>> > + ILI9341_INPUT_PRGB_ALIGNED = 0x1,
>> > + ILI9341_INPUT_UNKNOWN = 0xf,
>> > +};
>> > +
>> > +/**
>> > + * struct ili9341_config - the system specific ILI9341 configuration
>> > + * @width_mm: physical panel width [mm]
>> > + * @height_mm: physical panel height [mm]
>> > + * @input: the input/entry type used in this system, if this is set to
>> > + * ILI9341_INPUT_UNKNOWN the driver will try to figure it out by probing
>> > + * the hardware
>> > + * @dclk_active_high: data/pixel clock active high, data will be clocked
>> > + * in on the rising edge of the DCLK (this is usually the case).
>> > + * @de_active_high: DE (data entry) is active high
>> > + * @hsync_active_high: HSYNC is active high
>> > + * @vsync_active_high: VSYNC is active high
>> > + */
>> > +struct ili9341_config {
>> > + u32 width_mm;
>> > + u32 height_mm;
>> > + enum ili9341_input input;
>> > + bool dclk_active_high;
>> > + bool de_active_high;
>> > + bool hsync_active_high;
>> > + bool vsync_active_high;
>> > +};
>> > +
>> > +struct ili9341 {
>> > + struct device *dev;
>> > + const struct ili9341_config *conf;
>> > + struct drm_panel panel;
>> > + struct regmap *regmap;
>> > + struct gpio_desc *reset_gpio;
>> > + struct gpio_desc *dc_gpio;
>> > + enum ili9341_input input;
>>
>> > + struct videomode vm;
>> videomode is not used. So drop this field and drop the include files
>> that are no logner needed.
>>

dillon: ok

>>
>> > +};
>> > +
>> > +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel)
>> > +{
>> > + return container_of(panel, struct ili9341, panel);
>> > +}
>> > +
>> > +int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz,
>> > + u8 bpw, const void *buf, size_t len)
>> > +{
>> > + size_t max_chunk = spi_max_transfer_size(spi);
>> > + struct spi_transfer tr = {
>> const?
>>

dillon: ok

>>
>> > + .bits_per_word = bpw,
>> > + .speed_hz = speed_hz,
>> > + .len = len,
>> > + };
>> > + struct spi_message m;
>> > + size_t chunk;
>> > + int ret;
>> > +
>> > + spi_message_init_with_transfers(&m, &tr, 1);
>> > +
>> > + while (len) {
>> > + chunk = min(len, max_chunk);
>> > +
>> > + tr.tx_buf = buf;
>> > + tr.len = chunk;
>> > + buf += chunk;
>> > + len -= chunk;
>> > +
>> > + ret = spi_sync(spi, &m);
>> > + if (ret)
>> > + return ret;
>> > + }
>> > + return 0;
>> > +}
>> > +static int ili9341_regmap_spi_write(void *context, const void *data,
>> > + size_t count)
>> > +{
>> > + struct device *dev = context;
>> > + struct spi_device *spi = to_spi_device(dev);
>> > + struct ili9341 *ili = spi_get_drvdata(spi);
>> > + int ret = 0;
>> > +
>> > + gpiod_set_value_cansleep(ili->dc_gpio, 0);
>> > +
>> > + ret = ili9341_spi_transfer(spi, DEFAULT_SPI_SPEED, 8, data+0, 1);
>> > + if (ret || count == 1 ||
>> > + ((u8 *)data)[0] == ILI9341_GRAM ||
>> > + ((u8 *)data)[0] == ILI9341_DISPLAY_ON ||
>> > + ((u8 *)data)[0] == ILI9341_SLEEP_OUT ||
>> > + ((u8 *)data)[0] == ILI9341_DISPLAY_OFF)
>> > + return ret;
>> > +
>> > + gpiod_set_value_cansleep(ili->dc_gpio, 1);
>> > +
>> > + return ili9341_spi_transfer(spi, DEFAULT_SPI_SPEED, 8, data+1, count-1);
>> > +}
>> > +
>> > +static int ili9341_regmap_spi_read(void *context, const void *reg,
>> > + size_t reg_size, void *val, size_t val_size)
>> > +{
>> > + return 0;
>> > +}
>> Is this function really needed? If not delete it.
>>
> regmap will be drop in next patch.
>>
>> > +
>> > +static struct regmap_bus ili9341_regmap_bus = {
>> > + .write = ili9341_regmap_spi_write,
>> > + .read = ili9341_regmap_spi_read,
>> > + .reg_format_endian_default = REGMAP_ENDIAN_BIG,
>> > + .val_format_endian_default = REGMAP_ENDIAN_BIG,
>> > +};
>> > +
>> > +static bool ili9341_volatile_reg(struct device *dev, unsigned int reg)
>> > +{
>> > + return false;
>> > +}
>> Is this function really nedded? If not delete it.
>>
>> > +
>> > +static bool ili9341_writeable_reg(struct device *dev, unsigned int reg)
>> > +{
>> > + /* Just register 0 is read-only */
>> > + if (reg == 0x00)
>> > + return false;
>> > + return true;
>> > +}
>> > +
>> > +static const struct regmap_config ili9341_regmap_config = {
>> > + .reg_bits = 8,
>> > + .val_bits = 8,
>> > + .max_register = 0xff,
>> > + .cache_type = REGCACHE_RBTREE,
>> > + .volatile_reg = ili9341_volatile_reg,
>> > + .writeable_reg = ili9341_writeable_reg,
>> > +};
>> > +
>>
>> No error checks - consider something like:
>>
>> static int bulk_write(struct ili9341 *ili, u8 reg, const u8[] data, int len)
>> {
>> int err = ili->err;
>>
>> if (!err) {
>> err = regmap_bulk_write(ili->regmap, reg, data, len);
>> if (err) {
>> dev_err(...);
>> ili->err = err;
>> }
>> }
>>
>> return err;
>> }
>>
>> Then you can use this in the following, and make this more readable.
>>

dillon: ok, thanks for detail guide.

>
>>
>> > +static int ili9341_init(struct drm_panel *panel, struct ili9341 *ili)
>> > +{
>> > + regmap_bulk_write(ili->regmap, 0xca,
>> > + ili9341_cmd0, sizeof(ili9341_cmd0));
>> > + regmap_bulk_write(ili->regmap, ILI9341_POWERB,
>> > + ili9341_powerb, sizeof(ili9341_powerb));
>> > + regmap_bulk_write(ili->regmap, ILI9341_POWER_SEQ,
>> > + ili9341_power_seq, sizeof(ili9341_power_seq));
>> > + regmap_bulk_write(ili->regmap, ILI9341_DTCA,
>> > + ili9341_dtca, sizeof(ili9341_dtca));
>> > + regmap_bulk_write(ili->regmap, ILI9341_POWERA,
>> > + ili9341_powera, sizeof(ili9341_powera));
>> > + regmap_write(ili->regmap, ILI9341_PRC, ili9341_prc[0]);
>> > + regmap_bulk_write(ili->regmap, ILI9341_DTCB,
>> > + ili9341_dtcb, sizeof(ili9341_dtcb));
>> > + regmap_bulk_write(ili->regmap, ILI9341_FRC,
>> > + ili9341_frc, sizeof(ili9341_frc));
>> > + regmap_bulk_write(ili->regmap, ILI9341_DFC,
>> > + ili9341_dfc1, sizeof(ili9341_dfc1));
>> > + regmap_write(ili->regmap, ILI9341_POWER1, ili9341_power1[0]);
>> > + regmap_write(ili->regmap, ILI9341_POWER2, ili9341_power2[0]);
>> > + regmap_bulk_write(ili->regmap, ILI9341_VCOM1,
>> > + ili9341_vcom1, sizeof(ili9341_vcom1));
>> > + regmap_write(ili->regmap, ILI9341_VCOM2, ili9341_vcom2[0]);
>> > + regmap_write(ili->regmap, ILI9341_MAC, ili9341_mac[0]);
>> > + regmap_write(ili->regmap, ILI9341_3GAMMA_EN, ili9341_gamma_en[0]);
>> > + regmap_write(ili->regmap, ILI9341_RGB_INTERFACE, ili9341_rgb_intr[0]);
>> > + regmap_bulk_write(ili->regmap, ILI9341_DFC,
>> > + ili9341_dfc2, sizeof(ili9341_dfc2));
>> > +
>> > + /* colomn address set */
>> > + regmap_bulk_write(ili->regmap, ILI9341_COLUMN_ADDR,
>> > + ili9341_column_addr, sizeof(ili9341_column_addr));
>> > +
>> > + /* Page Address Set */
>> > + regmap_bulk_write(ili->regmap, ILI9341_PAGE_ADDR,
>> > + ili9341_page_addr, sizeof(ili9341_page_addr));
>> > + regmap_bulk_write(ili->regmap, ILI9341_INTERFACE,
>> > + ili9341_intr, sizeof(ili9341_intr));
>> > + regmap_write(ili->regmap, ILI9341_GRAM, 0);
>> > + msleep(200);
>> > +
>> > + regmap_write(ili->regmap, ILI9341_GAMMA, ili9341_gamma[0]);
>> > + regmap_bulk_write(ili->regmap, ILI9341_PGAMMA,
>> > + ili9341_pgamma, sizeof(ili9341_pgamma));
>> > + regmap_bulk_write(ili->regmap, ILI9341_NGAMMA,
>> > + ili9341_ngamma, sizeof(ili9341_ngamma));
>> > + regmap_write(ili->regmap, ILI9341_SLEEP_OUT, 0);
>> > + msleep(200);
>> > +
>> > + regmap_write(ili->regmap, ILI9341_DISPLAY_ON, 0);
>> > +
>> > + /* GRAM start writing */
>> > + regmap_write(ili->regmap, ILI9341_GRAM, 0);
>> > +
>> > + dev_info(ili->dev, "initialized display\n");
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +/*
>> > + * This power-on sequence if from the datasheet, page 57.
>> > + */
>> > +static int ili9341_power_on(struct ili9341 *ili)
>> > +{
>> > + /* Assert RESET */
>> > + gpiod_set_value(ili->reset_gpio, 1);
>> > +
>> > + msleep(20);
>> > +
>> > + /* De-assert RESET */
>> > + gpiod_set_value(ili->reset_gpio, 0);
>> > +
>> > + msleep(10);
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static int ili9341_power_off(struct ili9341 *ili)
>> > +{
>>
>> Assert reset?

dillon: will add reset-pin control here.

>
>
>>
>> > + return 0;
>> > +}
>> > +
>> > +static int ili9341_disable(struct drm_panel *panel)
>> > +{
>> > + struct ili9341 *ili = panel_to_ili9341(panel);
>> > + int ret;
>> > +
>> > + ret = regmap_write(ili->regmap, ILI9341_DISPLAY_OFF, 0);
>> > + if (ret) {
>> > + dev_err(ili->dev, "unable to go to standby mode\n");
>> > + return ret;
>> > + }
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static int ili9341_unprepare(struct drm_panel *panel)
>> > +{
>> > + struct ili9341 *ili = panel_to_ili9341(panel);
>> > +
>> > + return ili9341_power_off(ili);
>> > +}
>> > +
>> > +static int ili9341_prepare(struct drm_panel *panel)
>> > +{
>> > + struct ili9341 *ili = panel_to_ili9341(panel);
>> > + int ret;
>> > +
>> > + ret = ili9341_power_on(ili);
>> > + if (ret < 0)
>> > + return ret;
>> > +
>> > + ret = ili9341_init(panel, ili);
>> > + if (ret < 0)
>> > + ili9341_unprepare(panel);
>> > +
>> > + return ret;
>> > +}
>> > +
>> > +static int ili9341_enable(struct drm_panel *panel)
>> > +{
>> > + struct ili9341 *ili = panel_to_ili9341(panel);
>> > + int ret;
>> > +
>> > + ret = regmap_write(ili->regmap, ILI9341_DISPLAY_ON, 0);
>> > + if (ret) {
>> > + dev_err(ili->dev, "unable to enable panel\n");
>> > + return ret;
>> > + }
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +/* This is the only mode listed for parallel RGB in the datasheet */
>> > +static const struct drm_display_mode prgb_320x240_mode = {
>> > + .clock = 6100,
>> > + .hdisplay = 240,
>> > + .hsync_start = 240 + 10,
>> > + .hsync_end = 240 + 10 + 10,
>> > + .htotal = 280,
>> > + .vdisplay = 320,
>> > + .vsync_start = 320 + 4,
>> > + .vsync_end = 320 + 4 + 2,
>> > + .vtotal = 328,
>> > + .vrefresh = 60,
>> > + .flags = 0,
>> > +};
>> > +
>> > +static int ili9341_get_modes(struct drm_panel *panel,
>> > + struct drm_connector *connector)
>> > +{
>> > + struct ili9341 *ili = panel_to_ili9341(panel);
>> > + struct drm_device *drm = connector->dev;
>> > + struct drm_display_mode *mode;
>> > + struct drm_display_info *info;
>> > +
>> > + info = &connector->display_info;
>> > + info->width_mm = ili->conf->width_mm;
>> > + info->height_mm = ili->conf->height_mm;
>> > + if (ili->conf->dclk_active_high)
>> > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;
>> > + else
>> > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
>> > +
>> > + if (ili->conf->de_active_high)
>> > + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;
>> > + else
>> > + info->bus_flags |= DRM_BUS_FLAG_DE_LOW;
>> > +
>> > + switch (ili->input) {
>> > + case ILI9341_INPUT_PRGB_THROUGH:
>> > + case ILI9341_INPUT_PRGB_ALIGNED:
>> > + mode = drm_mode_duplicate(drm, &prgb_320x240_mode);
>> > + break;
>> > + default:
>> > + mode = NULL;
>> > + break;
>> > + }
>> > + if (!mode) {
>> > + DRM_ERROR("bad mode or failed to add mode\n");
>> > + return -EINVAL;
>> > + }
>> > + drm_mode_set_name(mode);
>> > + /*
>> > + * This is the preferred mode because most people are going
>> > + * to want to use the display with VGA type graphics.
>> > + */
>> > + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
>> > +
>> > + /* Set up the polarity */
>> > + if (ili->conf->hsync_active_high)
>> > + mode->flags |= DRM_MODE_FLAG_PHSYNC;
>> > + else
>> > + mode->flags |= DRM_MODE_FLAG_NHSYNC;
>> > + if (ili->conf->vsync_active_high)
>> > + mode->flags |= DRM_MODE_FLAG_PVSYNC;
>> > + else
>> > + mode->flags |= DRM_MODE_FLAG_NVSYNC;
>> > +
>> > + mode->width_mm = ili->conf->width_mm;
>> > + mode->height_mm = ili->conf->height_mm;
>> > + drm_mode_probed_add(connector, mode);
>> > +
>> > + return 1; /* Number of modes */
>> > +}
>> > +
>> > +static const struct drm_panel_funcs ili9341_drm_funcs = {
>> > + .disable = ili9341_disable,
>> > + .unprepare = ili9341_unprepare,
>> > + .prepare = ili9341_prepare,
>> > + .enable = ili9341_enable,
>> > + .get_modes = ili9341_get_modes,
>> > +};
>> > +
>> > +static int ili9341_probe(struct spi_device *spi)
>> > +{
>> > + struct device *dev = &spi->dev;
>> > + struct ili9341 *ili;
>> > + const struct regmap_config *regmap_config;
>> > + int ret;
>> > +
>> > + ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
>> > + if (!ili)
>> > + return -ENOMEM;
>> > +
>> > + spi_set_drvdata(spi, ili);
>> > +
>> > + ili->dev = dev;
>> > + /*
>> > + * Every new incarnation of this display must have a unique
>> > + * data entry for the system in this driver.
>> > + */
>> > + ili->conf = of_device_get_match_data(dev);
>> > + if (!ili->conf) {
>> > + dev_err(dev, "missing device configuration\n");
>> > + return -ENODEV;
>> > + }
>> > +
>> > + ili->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
>> > + if (IS_ERR(ili->reset_gpio)) {
>> > + dev_err(dev, "failed to get RESET GPIO\n");
>> > + return PTR_ERR(ili->reset_gpio);
>> > + }
>> > +
>> > + ili->dc_gpio = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
>> > + if (IS_ERR(ili->dc_gpio)) {
>> > + dev_err(dev, "failed to get DC GPIO\n");
>> > + return PTR_ERR(ili->dc_gpio);
>> > + }
>> > +
>> > + spi->bits_per_word = 8;
>> > + ret = spi_setup(spi);
>> > + if (ret < 0) {
>> > + dev_err(dev, "spi setup failed.\n");
>> > + return ret;
>> > + }
>> > +
>> > + regmap_config = &ili9341_regmap_config;
>> > +
>> > + ili->regmap = devm_regmap_init(dev, &ili9341_regmap_bus, dev,
>> > + regmap_config);
>> > + if (IS_ERR(ili->regmap)) {
>> > + dev_err(dev, "failed to allocate register map\n");
>> > + return PTR_ERR(ili->regmap);
>> > + }
>> > +
>> > + ili->input = ili->conf->input;
>> > +
>> > + drm_panel_init(&ili->panel, dev, &ili9341_drm_funcs,
>> > + DRM_MODE_CONNECTOR_DPI);
>> > +
>> > + return drm_panel_add(&ili->panel);
>> > +}
>> > +
>> > +static int ili9341_remove(struct spi_device *spi)
>> > +{
>> > + struct ili9341 *ili = spi_get_drvdata(spi);
>> > +
>> > + ili9341_power_off(ili);
>> > + drm_panel_remove(&ili->panel);
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +/*
>> > + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
>> > + */
>> > +static const struct ili9341_config ili9341_data = {
>> This should be named "disco" something as this is m32f429-disco
>> specific.
>>

dillon: ok

>>
>> > + .width_mm = 65,
>> > + .height_mm = 50,
>> > + .input = ILI9341_INPUT_PRGB_THROUGH,
>> > + .dclk_active_high = true,
>> > + .de_active_high = false,
>> > + .hsync_active_high = false,
>> > + .vsync_active_high = false,
>> > +};
>> > +
>> > +static const struct of_device_id ili9341_of_match[] = {
>> > + {
>> > + .compatible = "stm32f429,ltdc-panel",
>> > + .data = &ili9341_data,
>> > + },
>>
>>
>> > + {
>> > + .compatible = "ilitek,ili9341",
>> > + .data = NULL,
>> This part is wrong, as ilitek,ili9341 is just the generic part.
>> Only the first entry is relevant.
>>
>>

dillon: ok

>>
>> > + },
>> > + { }
>> > +};
>> > +MODULE_DEVICE_TABLE(of, ili9341_of_match);
>> > +
>> > +static struct spi_driver ili9341_driver = {
>> > + .probe = ili9341_probe,
>> > + .remove = ili9341_remove,
>> > + .driver = {
>> > + .name = "panel-ilitek-ili9341",
>> > + .of_match_table = ili9341_of_match,
>> > + },
>> > +};
>> > +module_spi_driver(ili9341_driver);
>> > +
>> > +MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>");
>> > +MODULE_DESCRIPTION("ILI9341 LCD panel driver");
>> > +MODULE_LICENSE("GPL v2");
>> > --
>> > 2.7.4

\
 
 \ /
  Last update: 2020-05-09 10:33    [W:0.400 / U:0.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site