lkml.org 
[lkml]   [2020]   [May]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [PATCH net-next 3/5] net: mvpp2: cls: Use RSS contexts to handle RSS tables
On Thu, Apr 23, 2020 at 7:00 PM Russell King - ARM Linux admin
<linux@armlinux.org.uk> wrote:
>
> On Tue, Apr 14, 2020 at 01:43:02AM +0200, Matteo Croce wrote:
> > On Tue, Apr 14, 2020 at 1:21 AM Maxime Chevallier
> > <maxime.chevallier@bootlin.com> wrote:
> > >
> > > The PPv2 controller has 8 RSS tables that are shared across all ports on
> > > a given PPv2 instance. The previous implementation allocated one table
> > > per port, leaving others unused.
> > >
> > > By using RSS contexts, we can make use of multiple RSS tables per
> > > port, one being the default table (always id 0), the other ones being
> > > used as destinations for flow steering, in the same way as rx rings.
> > >
> > > This commit introduces RSS contexts management in the PPv2 driver. We
> > > always reserve one table per port, allocated when the port is probed.
> > >
> > > The global table list is stored in the struct mvpp2, as it's a global
> > > resource. Each port then maintains a list of indices in that global
> > > table, that way each port can have it's own numbering scheme starting
> > > from 0.
> > >
> > > One limitation that seems unavoidable is that the hashing parameters are
> > > shared across all RSS contexts for a given port. Hashing parameters for
> > > ctx 0 will be applied to all contexts.
> > >
> > > Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
> >
> > Hi all,
> >
> > I noticed that enabling rxhash blocks the RX on my Macchiatobin. It
> > works fine with the 10G ports (the RX rate goes 4x up) but it
> > completely kills the gigabit interface.
> >
> > # 10G port
> > root@macchiatobin:~# iperf3 -c 192.168.0.2
> > Connecting to host 192.168.0.2, port 5201
> > [ 5] local 192.168.0.1 port 42394 connected to 192.168.0.2 port 5201
> > [ ID] Interval Transfer Bitrate Retr Cwnd
> > [ 5] 0.00-1.00 sec 941 MBytes 7.89 Gbits/sec 4030 250 KBytes
> > [ 5] 1.00-2.00 sec 933 MBytes 7.82 Gbits/sec 4393 240 KBytes
> > root@macchiatobin:~# ethtool -K eth0 rxhash on
> > root@macchiatobin:~# iperf3 -c 192.168.0.2
> > Connecting to host 192.168.0.2, port 5201
> > [ 5] local 192.168.0.1 port 42398 connected to 192.168.0.2 port 5201
> > [ ID] Interval Transfer Bitrate Retr Cwnd
> > [ 5] 0.00-1.00 sec 860 MBytes 7.21 Gbits/sec 428 410 KBytes
> > [ 5] 1.00-2.00 sec 859 MBytes 7.20 Gbits/sec 185 563 KBytes
> >
> > # gigabit port
> > root@macchiatobin:~# iperf3 -c turbo
> > Connecting to host turbo, port 5201
> > [ 5] local 192.168.85.42 port 45144 connected to 192.168.85.6 port 5201
> > [ ID] Interval Transfer Bitrate Retr Cwnd
> > [ 5] 0.00-1.00 sec 113 MBytes 948 Mbits/sec 0 407 KBytes
> > [ 5] 1.00-2.00 sec 112 MBytes 942 Mbits/sec 0 428 KBytes
> > root@macchiatobin:~# ethtool -K eth2 rxhash on
> > root@macchiatobin:~# iperf3 -c turbo
> > iperf3: error - unable to connect to server: Resource temporarily unavailable
> >
> > I've bisected and it seems that this commit causes the issue. I tried
> > to revert it on nex-next as a second test, but the code has changed a
> > lot much since, generating too much conflicts.
> > Can you have a look into this?
>
> This behaviour on eth2 is confirmed here on v5.6. Turning on rxhash
> appears to prevent eth2 working.
>
> Maxime, please look into this regression, thanks.
>
> --
> RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
> FTTC broadband for 0.8mile line in suburbia: sync at 10.2Mbps down 587kbps up
>

Hi,

What do you think about temporarily disabling it like this?

--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -5775,7 +5775,8 @@ static int mvpp2_port_probe(struct platform_device *pdev,
NETIF_F_HW_VLAN_CTAG_FILTER;

if (mvpp22_rss_is_supported()) {
- dev->hw_features |= NETIF_F_RXHASH;
+ if (port->phy_interface != PHY_INTERFACE_MODE_SGMII)
+ dev->hw_features |= NETIF_F_RXHASH;
dev->features |= NETIF_F_NTUPLE;
}

David, is this "workaround" too bad to get accepted?

Bye,

--
Matteo Croce
per aspera ad upstream

\
 
 \ /
  Last update: 2020-05-09 02:15    [W:0.080 / U:1.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site