lkml.org 
[lkml]   [2020]   [May]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 1/5] mmc: core: Extend mmc_of_parse() to parse CQE bindings
From
Date

On 5/6/2020 10:06 PM, Ulf Hansson wrote:
> On Wed, 6 May 2020 at 15:01, Veerabhadrarao Badiganti
> <vbadigan@codeaurora.org> wrote:
>>
>> On 4/28/2020 5:26 AM, Chun-Hung Wu wrote:
>>> Parse CQE bindings "supports-cqe" and "disable-cqe-dcmd"
>>> in mmc_of_parse().
>>>
>>> Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
>>> ---
>>> drivers/mmc/core/host.c | 5 +++++
>>> 1 file changed, 5 insertions(+)
>>>
>>> diff --git a/drivers/mmc/core/host.c b/drivers/mmc/core/host.c
>>> index c876872..47521c6 100644
>>> --- a/drivers/mmc/core/host.c
>>> +++ b/drivers/mmc/core/host.c
>>> @@ -302,6 +302,11 @@ int mmc_of_parse(struct mmc_host *host)
>>> host->caps2 |= MMC_CAP2_NO_SD;
>>> if (device_property_read_bool(dev, "no-mmc"))
>>> host->caps2 |= MMC_CAP2_NO_MMC;
>>> + if (device_property_read_bool(dev, "supports-cqe"))
>>> + host->caps2 |= MMC_CAP2_CQE;
>> This change is breaking emmc driver on qcom platforms where this dt
>> property is defined.
>>
>> [ 1.543453] cqhci_deactivate+0xc/0x38
>> [ 1.545627] sdhci_msm_reset+0x40/0x58
>> [ 1.549447] sdhci_do_reset+0x48/0x7c
>> [ 1.553180] __sdhci_read_caps+0x7c/0x214
>> [ 1.556913] sdhci_setup_host+0x58/0xce8
>> [ 1.560905] sdhci_msm_probe+0x588/0x8a4
>> [ 1.564900] platform_drv_probe+0x4c/0xb0
>>
>> So, we cant have this flag defined before sdhci_setup_host().
>>
>> I will have to clear this cap and re-enable it in our initialization.
> Thanks for reporting! I have dropped all the four patches from
> Chun-Hung, so we can figure out how to fix this.
>
> Please help to review the next version of the series.

Thanks Ulf.

Hi Chun-Hung,

On qcom controller CQE also gets reset when SDHC is reset. So we have to
explicitly disable CQE
by invoking  cqhci_deactivate() during sdhc reset

SDHC gets reset in sdhci_setup_host() even before cqe is initialized.
With MMC_CAP2_CQE_DCMD cap set even before sdhci_set_host(), we are
getting null pointer access with cqhci_deactivate().

If CQE getting reset with SDHC reset is generic (applicable to other
controllers) then you have revisit your logic.
If its not the case then only qcom driver would get affected.

I see you are updating sdhci-msm.c file as-well. How about including
below change besides your change?

@@ -1658,6 +1658,8 @@ static int sdhci_msm_cqe_add_host(struct
sdhci_host *host,
        if (host->caps & SDHCI_CAN_64BIT)
                host->alloc_desc_sz = 16;

+       /* Clear the CQE cap during setup host */
+       msm_host->mmc->caps2 &= ~MMC_CAP2_CQE;
+
        ret = sdhci_setup_host(host);

>>> + if (!device_property_read_bool(dev, "disable-cqe-dcmd")) {
>>> + host->caps2 |= MMC_CAP2_CQE_DCMD;
>>> + }
>>>
>>> /* Must be after "non-removable" check */
>>> if (device_property_read_u32(dev, "fixed-emmc-driver-type", &drv_type) == 0) {
> Kind regards
> Uffe

\
 
 \ /
  Last update: 2020-05-07 18:34    [W:0.061 / U:0.704 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site