lkml.org 
[lkml]   [2020]   [May]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/3] vfio-pci: Invalidate mmaps and block MMIO access on disabled memory
On Mon, May 04, 2020 at 12:26:43PM -0600, Alex Williamson wrote:
> On Fri, 1 May 2020 20:48:49 -0300
> Jason Gunthorpe <jgg@ziepe.ca> wrote:
>
> > On Fri, May 01, 2020 at 03:39:30PM -0600, Alex Williamson wrote:
> >
> > > static int vfio_pci_add_vma(struct vfio_pci_device *vdev,
> > > struct vm_area_struct *vma)
> > > {
> > > @@ -1346,15 +1450,49 @@ static vm_fault_t vfio_pci_mmap_fault(struct vm_fault *vmf)
> > > {
> > > struct vm_area_struct *vma = vmf->vma;
> > > struct vfio_pci_device *vdev = vma->vm_private_data;
> > > + vm_fault_t ret = VM_FAULT_NOPAGE;
> > >
> > > - if (vfio_pci_add_vma(vdev, vma))
> > > - return VM_FAULT_OOM;
> > > + /*
> > > + * Zap callers hold memory_lock and acquire mmap_sem, we hold
> > > + * mmap_sem and need to acquire memory_lock to avoid races with
> > > + * memory bit settings. Release mmap_sem, wait, and retry, or fail.
> > > + */
> > > + if (unlikely(!down_read_trylock(&vdev->memory_lock))) {
> > > + if (vmf->flags & FAULT_FLAG_ALLOW_RETRY) {
> > > + if (vmf->flags & FAULT_FLAG_RETRY_NOWAIT)
> > > + return VM_FAULT_RETRY;
> > > +
> > > + up_read(&vma->vm_mm->mmap_sem);
> > > +
> > > + if (vmf->flags & FAULT_FLAG_KILLABLE) {
> > > + if (!down_read_killable(&vdev->memory_lock))
> > > + up_read(&vdev->memory_lock);
> > > + } else {
> > > + down_read(&vdev->memory_lock);
> > > + up_read(&vdev->memory_lock);
> > > + }
> > > + return VM_FAULT_RETRY;
> > > + }
> > > + return VM_FAULT_SIGBUS;
> > > + }
> >
> > So, why have the wait? It isn't reliable - if this gets faulted from a
> > call site that can't handle retry then it will SIGBUS anyhow?
>
> Do such call sites exist? My assumption was that half of the branch
> was unlikely to ever occur.

hmm_range_fault() for instance doesn't set ALLOW_RETRY, I assume there
are enough other case to care about, but am not so sure

> > The weird use of a rwsem as a completion suggest that perhaps using
> > wait_event might improve things:
> >
> > disable:
> > // Clean out the vma list with zap, then:
> >
> > down_read(mm->mmap_sem)
>
> I assume this is simplifying the dance we do in zapping to first take
> vma_lock in order to walk vma_list, to find a vma from which we can
> acquire the mm, drop vma_lock, get mmap_sem, then re-get vma_lock
> below.

No, that has to stay..

> Also accounting that vma_list might be empty and we might need
> to drop and re-acquire vma_lock to get to another mm, so we really
> probably want to set pause_faults at the start rather than at the end.

New vmas should not created/faulted while vma_lock is held, so the
order shouldn't matter..

> > mutex_lock(vma_lock);
> > list_for_each_entry_safe()
> > // zap and remove all vmas
> >
> > pause_faults = true;
> > mutex_write(vma_lock);
> >
> > fault:
> > // Already have down_read(mmap_sem)
> > mutex_lock(vma_lock);
> > while (pause_faults) {
> > mutex_unlock(vma_lock)
> > wait_event(..., !pause_faults)
> > mutex_lock(vma_lock)
> > }
>
> Nit, we need to test the memory enable bit setting somewhere under this
> lock since it seems to be the only thing protecting it now.

I was thinking you'd keep the same locking for the memory enable bit,
the pause_faults is a shadow of that bit with locking connected to
vma_lock..

> > list_add()
> > remap_pfn()
> > mutex_unlock(vma_lock)
>
> The read and write file ops would need similar mechanisms.

Keep using the rwsem?

> > enable:
> > pause_faults = false
> > wake_event()
>
> Hmm, vma_lock was dropped above and not re-acquired here.

I was thinking this would be under a continous rwlock

> I'm not sure if it was an oversight that pause_faults was not tested
> in the disable path, but this combination appears to lead to
> concurrent writers and serialized readers??

? pause_faults only exists to prevent the vm_ops fault callback from
progressing to a fault. I don't think any concurrancy is lost

> > The only requirement here is that while inside the write side of
> > memory_lock you cannot touch user pages (ie no copy_from_user/etc)
>
> I'm lost at this statement, I can only figure the above works if we
> remove memory_lock. Are you referring to a different lock? Thanks,

No

This is just an approach to avoid the ABBA deadlock problem when using
a rwsem by using a looser form of lock combined witih the already
correctly nested vma_lock.

Stated another way, you can keep the existing memory_lock as is, if it
is structured like this:

disable:
down_read(mmap_sem)
mutex_lock(vma_lock)
list_for_each_entry_safe()
// zap and remove all vmas
down_write(memory_lock) // Now inside vma_lock!
mutex_unlock(vma_lock)
up_read(mmap_sem

[ do the existing stuff under memory_lock ]


fault:
mutex_lock(vma_lock)
down_write(memory_lock)
remap_pfn
up_write(memory_lock)
mutex_unlock(vma_lock)

enable:
up_write(memory_lock)

Ie the key is to organize things to move the down_write(memory_lock)
to be under the mmap_sem/vma_lock

Jason

\
 
 \ /
  Last update: 2020-05-04 20:45    [W:0.512 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site