lkml.org 
[lkml]   [2020]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] HID: usbhid: do not sleep when opening device
On Fri, May 29, 2020 at 05:48:26PM -0700, Guenter Roeck wrote:
> On Fri, May 29, 2020 at 4:50 PM Nicolas Boichat <drinkcat@chromium.org> wrote:
> >
> > On Sat, May 30, 2020 at 3:59 AM Dmitry Torokhov
> > <dmitry.torokhov@gmail.com> wrote:
> > >
> > > usbhid tries to give the device 50 milliseconds to drain its queues
> > > when opening the device, but does it naively by simply sleeping in open
> > > handler, which slows down device probing (and thus may affect overall
> > > boot time).
> > >
> > > However we do not need to sleep as we can instead mark a point of time
> > > in the future when we should start processing the events.
> > >
> > > Reported-by: Nicolas Boichat <drinkcat@chromium.org>
> > > Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
> > > ---
> > > drivers/hid/usbhid/hid-core.c | 27 +++++++++++++++------------
> > > drivers/hid/usbhid/usbhid.h | 1 +
> > > 2 files changed, 16 insertions(+), 12 deletions(-)
> > >
> > > diff --git a/drivers/hid/usbhid/hid-core.c b/drivers/hid/usbhid/hid-core.c
> > > index c7bc9db5b192..e69992e945b2 100644
> > > --- a/drivers/hid/usbhid/hid-core.c
> > > +++ b/drivers/hid/usbhid/hid-core.c
> > > @@ -95,6 +95,19 @@ static int hid_start_in(struct hid_device *hid)
> > > set_bit(HID_NO_BANDWIDTH, &usbhid->iofl);
> > > } else {
> > > clear_bit(HID_NO_BANDWIDTH, &usbhid->iofl);
> > > +
> > > + if (test_and_clear_bit(HID_RESUME_RUNNING,
> > > + &usbhid->iofl)) {
> > > + /*
> > > + * In case events are generated while nobody was
> > > + * listening, some are released when the device
> > > + * is re-opened. Wait 50 msec for the queue to
> > > + * empty before allowing events to go through
> > > + * hid.
> > > + */
> > > + usbhid->input_start_time = jiffies +
> > > + msecs_to_jiffies(50);
> > > + }
> > > }
> > > }
> > > spin_unlock_irqrestore(&usbhid->lock, flags);
> > > @@ -280,7 +293,8 @@ static void hid_irq_in(struct urb *urb)
> > > if (!test_bit(HID_OPENED, &usbhid->iofl))
> > > break;
> > > usbhid_mark_busy(usbhid);
> > > - if (!test_bit(HID_RESUME_RUNNING, &usbhid->iofl)) {
> > > + if (!test_bit(HID_RESUME_RUNNING, &usbhid->iofl) &&
> > > + time_after(jiffies, usbhid->input_start_time)) {
> >
> > Are we worried about jiffies overflowing (32-bit@1000Hz is "only" 49.7 days...)
> >
>
> time_after() is overflow-safe. That is why it is used and jiffies is
> not compared directly.

Well, it is overflow safe, but still can not measure more than 50 days,
so if you have a device open for 50+ days there will be a 50msec gap
where it may lose events.

I guess we can switch to ktime(). A bit more expensive on 32 bits, but
in reality I do not think anyone would care.

Thanks.

--
Dmitry

\
 
 \ /
  Last update: 2020-05-30 03:11    [W:0.083 / U:0.876 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site