lkml.org 
[lkml]   [2020]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 3/3] ARC: [plat-hsdk-4xd] initial port for HSDK-4xD board
Date
+CC Rob H (it seems the CC in patch didn't go thru)

On 5/29/20 4:55 AM, Eugeniy Paltsev wrote:
> This initial port adds support of ARC HS4x/HS4xD Development Kit board with some
> basic features such serial port, USB, SD/MMC, SPI flash, Ethernet and others.
>
> The HSDK-4xD board has much in common with its predecessor - HSDK board.
> However HSDK-4xD has some differences in comparison with its predecessor:
> * based on quad core ARC HS48/HS47D processor (instead of quad core ARC HS38)
> * has ThinkSilicon GPU (instead of Vivante GPU)
> * has ARC PGU and HDMI output
> * has separate SDIO controller for WiFi module
> * has additional timers with clocksource independent from CPU clocksource
> (required for DVFS)
> * has performance counters interrupt
> * other minor stuff
>
> NOTE:
> HSDK-4xD and HSDK may share significant part of DTS so we can move this common
> part to one .dtsi file (as we have done it in U-boot). However we have quite
> enough out of the tree patches for tweaking HSDK DTS (patches in out
> verification flow, patches for run in simulation, etc...), so I'd prefer to
> keep HSDK DTS untouched. That's why HSDK-4xD DTS is created as an separate file.

I agree we need a different version of DTB for wiring up perf interrupt and gpu
(whether full copy or common parts in a dtsi I don't care). But just curious if
the "other" mods to DTS were temporary "hacks" for various testing things or do
you intend to actually productize/upstream them at some point. I mean you can
alsoways create a local copy for those and point your .config to it, do that is
not a reason to create a new dtb ! I know this is bike shedding...


> Cc: Rob Herring <robh+dt@kernel.org>
> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
> ---
> arch/arc/boot/dts/hsdk-4xd.dts | 322 ++++++++++++++++++++++++++++
> arch/arc/configs/hsdk_4xd_defconfig | 99 +++++++++
> arch/arc/kernel/devtree.c | 1 +
> arch/arc/plat-hsdk/Kconfig | 24 ++-
> arch/arc/plat-hsdk/platform.c | 6 +
> 5 files changed, 451 insertions(+), 1 deletion(-)
> create mode 100644 arch/arc/boot/dts/hsdk-4xd.dts
> create mode 100644 arch/arc/configs/hsdk_4xd_defconfig
>
> diff --git a/arch/arc/boot/dts/hsdk-4xd.dts b/arch/arc/boot/dts/hsdk-4xd.dts
> new file mode 100644
> index 000000000000..2b7f76a01e3e
> --- /dev/null
> +++ b/arch/arc/boot/dts/hsdk-4xd.dts
> @@ -0,0 +1,322 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (C) 2020 Synopsys, Inc. (www.synopsys.com)
> + */
> +
> +/*
> + * Device Tree for ARC HS4x/HS4xD Development Kit
> + */
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/reset/snps,hsdk-reset.h>
> +
> +/ {
> + model = "snps,hsdk-4xd";
> + compatible = "snps,hsdk-4xd";
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + chosen {
> + bootargs = "earlycon=uart8250,mmio32,0xf0005000,115200n8 console=ttyS0,115200n8 debug print-fatal-signals=1";
> + };
> +
> + aliases {
> + ethernet = &gmac;
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + device_type = "cpu";
> + compatible = "snps,archs48";
> + reg = <0>;
> + clocks = <&core_clk>;
> + };
> +
> + cpu@1 {
> + device_type = "cpu";
> + compatible = "snps,archs48";
> + reg = <1>;
> + clocks = <&core_clk>;
> + };
> +
> + cpu@2 {
> + device_type = "cpu";
> + compatible = "snps,archs48";
> + reg = <2>;
> + clocks = <&core_clk>;
> + };
> +
> + cpu@3 {
> + device_type = "cpu";
> + compatible = "snps,archs48";
> + reg = <3>;
> + clocks = <&core_clk>;
> + };
> + };
> +
> + input_clk: input-clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <33333333>;
> + };
> +
> + reg_5v0: regulator-5v0 {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "5v0-supply";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + cpu_intc: cpu-interrupt-controller {
> + compatible = "snps,archs-intc";
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + idu_intc: idu-interrupt-controller {
> + compatible = "snps,archs-idu-intc";
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + interrupt-parent = <&cpu_intc>;
> + };
> +
> + arcpct: pct {
> + compatible = "snps,archs-pct";
> + interrupt-parent = <&cpu_intc>;
> + interrupts = <20>;
> + };
> +
> + /* TIMER0 with interrupt for clockevent */
> + timer {
> + compatible = "snps,arc-timer";
> + interrupts = <16>;
> + interrupt-parent = <&cpu_intc>;
> + clocks = <&core_clk>;
> + };
> +
> + /* 64-bit Global Free Running Counter */
> + gfrc {
> + compatible = "snps,archs-timer-gfrc";
> + clocks = <&core_clk>;
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupt-parent = <&idu_intc>;
> +
> + ranges = <0x00000000 0x0 0xf0000000 0x10000000>;
> +
> + cgu_rst: reset-controller@8a0 {
> + compatible = "snps,hsdk-reset";
> + #reset-cells = <1>;
> + reg = <0x8a0 0x4>, <0xff0 0x4>;
> + };
> +
> + core_clk: core-clk@0 {
> + compatible = "snps,hsdk-core-pll-clock";
> + reg = <0x00 0x10>, <0x14b8 0x4>;
> + #clock-cells = <0>;
> + clocks = <&input_clk>;
> +
> + /*
> + * Set initial core pll output frequency to 1GHz.
> + * It will be applied at the core pll driver probing
> + * on early boot.
> + */
> + assigned-clocks = <&core_clk>;
> + assigned-clock-rates = <1000000000>;
> + };
> +
> + serial: serial@5000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x5000 0x100>;
> + clock-frequency = <33330000>;
> + interrupts = <6>;
> + baud = <115200>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + };
> +
> + gmacclk: gmacclk {
> + compatible = "fixed-clock";
> + clock-frequency = <400000000>;
> + #clock-cells = <0>;
> + };
> +
> + mmcclk_ciu: mmcclk-ciu {
> + compatible = "fixed-clock";
> + /*
> + * DW sdio controller has external ciu clock divider
> + * controlled via register in SDIO IP. Due to its
> + * unexpected default value (it should divide by 1
> + * but it divides by 8) SDIO IP uses wrong clock and
> + * works unstable (see STAR 9001204800)
> + * We switched to the minimum possible value of the
> + * divisor (div-by-2) in HSDK platform code.
> + * So add temporary fix and change clock frequency
> + * to 50000000 Hz until we fix dw sdio driver itself.
> + */
> + clock-frequency = <50000000>;
> + #clock-cells = <0>;
> + };
> +
> + mmcclk_biu: mmcclk-biu {
> + compatible = "fixed-clock";
> + clock-frequency = <400000000>;
> + #clock-cells = <0>;
> + };
> +
> + dmac_core_clk: dmac-core-clk {
> + compatible = "fixed-clock";
> + clock-frequency = <400000000>;
> + #clock-cells = <0>;
> + };
> +
> + dmac_cfg_clk: dmac-gpu-cfg-clk {
> + compatible = "fixed-clock";
> + clock-frequency = <200000000>;
> + #clock-cells = <0>;
> + };
> +
> + gmac: ethernet@8000 {
> + #interrupt-cells = <1>;
> + compatible = "snps,dwmac";
> + reg = <0x8000 0x2000>;
> + interrupts = <10>;
> + interrupt-names = "macirq";
> + phy-mode = "rgmii";
> + snps,pbl = <32>;
> + snps,multicast-filter-bins = <256>;
> + clocks = <&gmacclk>;
> + clock-names = "stmmaceth";
> + phy-handle = <&phy0>;
> + resets = <&cgu_rst HSDK_ETH_RESET>;
> + reset-names = "stmmaceth";
> + mac-address = [00 00 00 00 00 00]; /* Filled in by U-Boot */
> + dma-coherent;
> +
> + tx-fifo-depth = <4096>;
> + rx-fifo-depth = <4096>;
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + };
> + };
> + };
> +
> + ohci@60000 {
> + compatible = "snps,hsdk-v1.0-ohci", "generic-ohci";
> + reg = <0x60000 0x100>;
> + interrupts = <15>;
> + resets = <&cgu_rst HSDK_USB_RESET>;
> + dma-coherent;
> + };
> +
> + ehci@40000 {
> + compatible = "snps,hsdk-v1.0-ehci", "generic-ehci";
> + reg = <0x40000 0x100>;
> + interrupts = <15>;
> + resets = <&cgu_rst HSDK_USB_RESET>;
> + dma-coherent;
> + };
> +
> + mmc@a000 {
> + compatible = "altr,socfpga-dw-mshc";
> + reg = <0xa000 0x400>;
> + num-slots = <1>;
> + fifo-depth = <16>;
> + card-detect-delay = <200>;
> + clocks = <&mmcclk_biu>, <&mmcclk_ciu>;
> + clock-names = "biu", "ciu";
> + interrupts = <12>;
> + bus-width = <4>;
> + dma-coherent;
> + };
> +
> + spi0: spi@20000 {
> + compatible = "snps,dw-apb-ssi";
> + reg = <0x20000 0x100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <16>;
> + num-cs = <2>;
> + reg-io-width = <4>;
> + clocks = <&input_clk>;
> + cs-gpios = <&creg_gpio 0 GPIO_ACTIVE_LOW>,
> + <&creg_gpio 1 GPIO_ACTIVE_LOW>;
> +
> + spi-flash@0 {
> + compatible = "sst26wf016b", "jedec,spi-nor";
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <4000000>;
> + };
> +
> + adc@1 {
> + compatible = "ti,adc108s102";
> + reg = <1>;
> + vref-supply = <&reg_5v0>;
> + spi-max-frequency = <1000000>;
> + };
> + };
> +
> + creg_gpio: gpio@14b0 {
> + compatible = "snps,creg-gpio-hsdk";
> + reg = <0x14b0 0x4>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + ngpios = <2>;
> + };
> +
> + gpio: gpio@3000 {
> + compatible = "snps,dw-apb-gpio";
> + reg = <0x3000 0x20>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + gpio_port_a: gpio-controller@0 {
> + compatible = "snps,dw-apb-gpio-port";
> + gpio-controller;
> + #gpio-cells = <2>;
> + snps,nr-gpios = <24>;
> + reg = <0>;
> + };
> + };
> +
> + dmac: dmac@80000 {
> + compatible = "snps,axi-dma-1.01a";
> + reg = <0x80000 0x400>;
> + interrupts = <27>;
> + clocks = <&dmac_core_clk>, <&dmac_cfg_clk>;
> + clock-names = "core-clk", "cfgr-clk";
> +
> + dma-channels = <4>;
> + snps,dma-masters = <2>;
> + snps,data-width = <3>;
> + snps,block-size = <4096 4096 4096 4096>;
> + snps,priority = <0 1 2 3>;
> + snps,axi-max-burst-len = <16>;
> + };
> + };
> +
> + memory@80000000 {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + device_type = "memory";
> + reg = <0x0 0x80000000 0x0 0x40000000>; /* 1 GB lowmem */
> + /* 0x1 0x00000000 0x0 0x40000000>; 1 GB highmem */
> + };
> +};
> diff --git a/arch/arc/configs/hsdk_4xd_defconfig b/arch/arc/configs/hsdk_4xd_defconfig
> new file mode 100644
> index 000000000000..bf78f745a0f6
> --- /dev/null
> +++ b/arch/arc/configs/hsdk_4xd_defconfig
> @@ -0,0 +1,99 @@
> +CONFIG_SYSVIPC=y
> +# CONFIG_CROSS_MEMORY_ATTACH is not set
> +CONFIG_NO_HZ_IDLE=y
> +CONFIG_HIGH_RES_TIMERS=y
> +CONFIG_PREEMPT=y
> +CONFIG_IKCONFIG=y
> +CONFIG_IKCONFIG_PROC=y
> +CONFIG_NAMESPACES=y
> +# CONFIG_UTS_NS is not set
> +# CONFIG_PID_NS is not set
> +CONFIG_BLK_DEV_INITRD=y
> +CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3=y
> +CONFIG_EMBEDDED=y
> +CONFIG_PERF_EVENTS=y
> +# CONFIG_VM_EVENT_COUNTERS is not set
> +# CONFIG_COMPAT_BRK is not set
> +CONFIG_SLAB=y
> +CONFIG_ARC_SOC_HSDK=y
> +CONFIG_ARC_BOARD_HSDK_4XD=y
> +CONFIG_SMP=y
> +CONFIG_ARC_TUNE_MCPU="-mcpu=hs4x_rel31"
> +CONFIG_ARC_DSP_KERNEL=y
> +CONFIG_LINUX_LINK_BASE=0x90000000
> +CONFIG_LINUX_RAM_BASE=0x80000000
> +CONFIG_ARC_BUILTIN_DTB_NAME="hsdk-4xd"
> +CONFIG_JUMP_LABEL=y
> +CONFIG_MODULES=y
> +CONFIG_MODULE_UNLOAD=y
> +# CONFIG_COMPACTION is not set
> +CONFIG_NET=y
> +CONFIG_PACKET=y
> +CONFIG_UNIX=y
> +CONFIG_INET=y
> +CONFIG_DEVTMPFS=y
> +# CONFIG_STANDALONE is not set
> +# CONFIG_PREVENT_FIRMWARE_BUILD is not set
> +CONFIG_MTD=y
> +CONFIG_MTD_SPI_NOR=y
> +CONFIG_BLK_DEV_RAM=y
> +CONFIG_SCSI=y
> +CONFIG_BLK_DEV_SD=y
> +CONFIG_NETDEVICES=y
> +CONFIG_STMMAC_ETH=y
> +CONFIG_MICREL_PHY=y
> +CONFIG_INPUT_EVDEV=y
> +# CONFIG_INPUT_KEYBOARD is not set
> +# CONFIG_INPUT_MOUSE is not set
> +# CONFIG_SERIO is not set
> +# CONFIG_LEGACY_PTYS is not set
> +CONFIG_SERIAL_8250=y
> +CONFIG_SERIAL_8250_CONSOLE=y
> +CONFIG_SERIAL_8250_DW=y
> +CONFIG_SERIAL_OF_PLATFORM=y
> +# CONFIG_HW_RANDOM is not set
> +CONFIG_SPI=y
> +CONFIG_SPI_DESIGNWARE=y
> +CONFIG_SPI_DW_MMIO=y
> +CONFIG_GPIOLIB=y
> +CONFIG_GPIO_SYSFS=y
> +CONFIG_GPIO_DWAPB=y
> +CONFIG_GPIO_SNPS_CREG=y
> +# CONFIG_HWMON is not set
> +CONFIG_THERMAL=y
> +CONFIG_REGULATOR=y
> +CONFIG_REGULATOR_FIXED_VOLTAGE=y
> +CONFIG_DRM=y
> +# CONFIG_DRM_FBDEV_EMULATION is not set
> +CONFIG_DRM_UDL=y
> +CONFIG_FB=y
> +CONFIG_FRAMEBUFFER_CONSOLE=y
> +CONFIG_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_HCD_PLATFORM=y
> +CONFIG_USB_OHCI_HCD=y
> +CONFIG_USB_OHCI_HCD_PLATFORM=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_MMC=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_PLTFM=y
> +CONFIG_MMC_DW=y
> +CONFIG_DMADEVICES=y
> +CONFIG_DW_AXI_DMAC=y
> +CONFIG_IIO=y
> +CONFIG_TI_ADC108S102=y
> +CONFIG_EXT3_FS=y
> +CONFIG_VFAT_FS=y
> +CONFIG_TMPFS=y
> +CONFIG_NFS_FS=y
> +CONFIG_NFS_V3_ACL=y
> +CONFIG_NLS_CODEPAGE_437=y
> +CONFIG_NLS_ISO8859_1=y
> +CONFIG_CRYPTO_ECHAINIV=y
> +# CONFIG_ENABLE_MUST_CHECK is not set
> +CONFIG_STRIP_ASM_SYMS=y
> +CONFIG_SOFTLOCKUP_DETECTOR=y
> +CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=10
> +# CONFIG_SCHED_DEBUG is not set
> +# CONFIG_DEBUG_PREEMPT is not set
> +# CONFIG_FTRACE is not set
> diff --git a/arch/arc/kernel/devtree.c b/arch/arc/kernel/devtree.c
> index fa86d13df5ed..81f881af7356 100644
> --- a/arch/arc/kernel/devtree.c
> +++ b/arch/arc/kernel/devtree.c
> @@ -27,6 +27,7 @@ static void __init arc_set_early_base_baud(unsigned long dt_root)
> if (of_flat_dt_is_compatible(dt_root, "abilis,arc-tb10x"))
> arc_base_baud = 166666666; /* Fixed 166.6MHz clk (TB10x) */
> else if (of_flat_dt_is_compatible(dt_root, "snps,arc-sdp") ||
> + of_flat_dt_is_compatible(dt_root, "snps,hsdk-4xd") ||
> of_flat_dt_is_compatible(dt_root, "snps,hsdk"))
> arc_base_baud = 33333333; /* Fixed 33MHz clk (AXS10x & HSDK) */
> else if (of_flat_dt_is_compatible(dt_root, "ezchip,arc-nps"))
> diff --git a/arch/arc/plat-hsdk/Kconfig b/arch/arc/plat-hsdk/Kconfig
> index ce8101834518..3bf80eceebae 100644
> --- a/arch/arc/plat-hsdk/Kconfig
> +++ b/arch/arc/plat-hsdk/Kconfig
> @@ -3,10 +3,32 @@
> #
>
> menuconfig ARC_SOC_HSDK
> - bool "ARC HS Development Kit SOC"
> + bool "ARC HSDK or HSDK-4xD SoCs"
> depends on ISA_ARCV2
> select ARC_HAS_ACCL_REGS
> select ARC_IRQ_NO_AUTOSAVE
> select CLK_HSDK
> select RESET_HSDK
> select HAVE_PCI
> +
> +menu "HSDK / HSDK-4xD options"
> + visible if ARC_SOC_HSDK
> +
> +choice
> + prompt "HSDK board type"
> +
> +config ARC_BOARD_HSDK
> + bool "ARC HS Development Kit"
> + help
> + ARC HS Development Kit based on quad core ARC HS38 processor
> +
> +config ARC_BOARD_HSDK_4XD
> + bool "ARC HS4x/HS4xD Development Kit"
> + select ARC_LPB_DISABLE
> + help
> + ARC HS4x/HS4xD Development Kit based on quad core ARC HS48/HS47D
> + processor
> +
> +endchoice

You also need to update existing hsdk.dts to add CONFIG_ARC_BOARD_HSDK

> +
> +endmenu
> diff --git a/arch/arc/plat-hsdk/platform.c b/arch/arc/plat-hsdk/platform.c
> index 0b961a2a10b8..74e2508cfd1e 100644
> --- a/arch/arc/plat-hsdk/platform.c
> +++ b/arch/arc/plat-hsdk/platform.c
> @@ -331,7 +331,13 @@ static void __init hsdk_init_early(void)
> hsdk_enable_gpio_intc_wire();
> }
>
> +/*
> + * As we aren't going to run HSDK-4xD Linux image on HSDK and vise versa let's
> + * don't add additional machine entry but instead add new compatible to existing one and
> + * resolve all differences in compile time with #ifdef's.
> + */
> static const char *hsdk_compat[] __initconst = {
> + "snps,hsdk-4xd",
> "snps,hsdk",
> NULL,
> };
>

I don't see how the comment above relates to change. Infact the change *does*
potentially allow one image to run on other (with say old DTB).

The change itself is good ether way as ARC_SOC_HSDK ties both tof them together
and we don't need a different machine array.

Since I don't have the new board yet is there a technical reason we can't run the
image for old board on new one (assume I don't care about the GPU and ignore perf
interrupt).

-Vineet
\
 
 \ /
  Last update: 2020-05-29 23:15    [W:0.309 / U:0.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site