lkml.org 
[lkml]   [2020]   [May]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 020/105] drm/vc4: plane: Create overlays for any CRTC
Date
Now that we have everything in place, we can now register all the overlay
planes that can be assigned to all the CRTCs.

This has two side effects:

- The number of overlay planes is reduced from 24 to 8. This is temporary
and will be increased again in the next patch.

- The ID of the various planes is changed again, and we will now have all
the primary planes, then all the overlay planes and finally the cursor
planes. This shouldn't cause any issue since the ordering between
primary, overlay and cursor planes is preserved.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 35 +++++++++++++++++-----------------
1 file changed, 18 insertions(+), 17 deletions(-)

diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index 824c188980b0..5335123ae2a0 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -1378,26 +1378,27 @@ int vc4_plane_create_additional_planes(struct drm_device *drm)
struct drm_crtc *crtc;
unsigned int i;

- drm_for_each_crtc(crtc, drm) {
- /* Set up some arbitrary number of planes. We're not limited
- * by a set number of physical registers, just the space in
- * the HVS (16k) and how small an plane can be (28 bytes).
- * However, each plane we set up takes up some memory, and
- * increases the cost of looping over planes, which atomic
- * modesetting does quite a bit. As a result, we pick a
- * modest number of planes to expose, that should hopefully
- * still cover any sane usecase.
- */
- for (i = 0; i < 8; i++) {
- struct drm_plane *plane =
- vc4_plane_init(drm, DRM_PLANE_TYPE_OVERLAY);
+ /* Set up some arbitrary number of planes. We're not limited
+ * by a set number of physical registers, just the space in
+ * the HVS (16k) and how small an plane can be (28 bytes).
+ * However, each plane we set up takes up some memory, and
+ * increases the cost of looping over planes, which atomic
+ * modesetting does quite a bit. As a result, we pick a
+ * modest number of planes to expose, that should hopefully
+ * still cover any sane usecase.
+ */
+ for (i = 0; i < 8; i++) {
+ struct drm_plane *plane =
+ vc4_plane_init(drm, DRM_PLANE_TYPE_OVERLAY);

- if (IS_ERR(plane))
- continue;
+ if (IS_ERR(plane))
+ continue;

- plane->possible_crtcs = drm_crtc_mask(crtc);
- }
+ plane->possible_crtcs =
+ GENMASK(drm->mode_config.num_crtc - 1, 0);
+ }

+ drm_for_each_crtc(crtc, drm) {
/* Set up the legacy cursor after overlay initialization,
* since we overlay planes on the CRTC in the order they were
* initialized.
--
git-series 0.9.1
\
 
 \ /
  Last update: 2020-05-27 17:57    [W:1.501 / U:0.968 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site