lkml.org 
[lkml]   [2020]   [May]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH v2 0/3] Prefer working VT console over SPCR and device-tree chosen stdout-path
On Fri 2020-05-15 22:27:02, Alper Nebi Yasak wrote:
> On 13/05/2020 17:37, Petr Mladek wrote:
> > On Thu 2020-04-30 19:14:34, Alper Nebi Yasak wrote:
> I think things run roughly in the following order (from what I can
> decipher from kernel messages) and I think it matches your explanations:
>
> | ACPI SPCR | dt chosen stdout-path |
> +=================================+=================================+
> | acpi_parse_spcr() | |
> | -> add_preferred_console(uart0) | |
> | (if not on x86) | |
> +---------------------------------+---------------------------------+
> | console_setup() |
> | -> add_preferred_console(tty0) |
> | (if console=tty0) |
> +---------------------------------+---------------------------------+
> | register_console(vt) |
> +---------------------------------+---------------------------------+
> | | of_console_check() |
> | | -> add_preferred_console(uart2) |
> | | (if no console arg) |
> +---------------------------------+---------------------------------+
> | register_console(serial) |
> +---------------------------------+---------------------------------+


I was first a bit confused by the above table. The order looks fine
but I was not sure about the indentation. I think that some more
details are needed to get the picture and context.

I see the following order in start_kernel():

1. Add spcr consoles: by acpi_parse_spcr() called from setup_arch().
2. Add and register early consoles: by parse_early_param()
3. Add normal consoles from command line: by parse_args()

4. Register tty console: by vty_init() called via long chain
from fs_initcall(chr_dev_init). It seems to be init call
in 5th round, see include/linux/init.h

5. Register other (serial) consoles are most likely registered from
device_initcall() in 6th round, see include/linux/init.h.

The consoles defined by the device tree are not added directly.
Instead, the probe() callbacks checks whether such console is
selected in device tree by of_console_check() called from
uart_add_one_port().


> > My suggestion is:
> >
> > + Fix SPCR setting or device tree of your device when the defaults
> > are not as expected.
>
> Maybe I can get QEMU's SPCR use conditional on the existence a
> framebuffer, and get distributions to remove stdout-path from certain
> device-trees; but that would disable the serial console completely
> (instead of having it enabled where tty0 is still preferred).

I am afraid that this is a problem with many defaults. They might be
good enough for many people but others would want something else.

It might be acceptable to add consoles. But it might be a problem to
remove consoles or change the currently preferred one.

The only exception would be when most people are annoyed with the
current default. But this need to be discussed with people familiar
with the given architecture or device.


> > + Use command line to force your value when the defaults are not
> > as expected and you could not change them.
>
> This works; but I'd have to know the machine's serial configuration in
> advance to put it in the cmdline as "console=<serial> console=tty0", or
> lose the serial console as in the above. (A "console=dt" like that
> "console=spcr" patch you linked to would be useful here if it existed.)

The generic parameters: console=tty, console=serial, console=dt, console=spcr
looks fine to me. IMHO, the only problem might be when a particular
serial console drive is not able to guess reasonable defaults for the
baud rate, etc.

Best Regards,
Petr

\
 
 \ /
  Last update: 2020-05-25 15:04    [W:0.050 / U:1.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site