lkml.org 
[lkml]   [2020]   [May]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v6 10/19] mtd: spi-nor: core: use dummy cycle and address width info from SFDP
Date
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in octal DTR mode.
Use that information to send the correct Read SR command.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
drivers/mtd/spi-nor/core.c | 25 +++++++++++++++++++++++--
1 file changed, 23 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 642e3c07acf9..2ad248140b6c 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -357,6 +357,8 @@ int spi_nor_write_disable(struct spi_nor *nor)
static int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
{
int ret;
+ u8 addr_bytes = nor->params->rdsr_addr_nbytes;
+ u8 dummy = nor->params->rdsr_dummy;

if (nor->spimem) {
struct spi_mem_op op =
@@ -365,10 +367,21 @@ static int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_IN(1, sr, 1));

+ if (spi_nor_protocol_is_dtr(nor->reg_proto)) {
+ op.addr.nbytes = addr_bytes;
+ op.addr.val = 0;
+ op.dummy.nbytes = dummy;
+ }
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
- ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDSR,
- sr, 1);
+ if (spi_nor_protocol_is_dtr(nor->reg_proto))
+ ret = -ENOTSUPP;
+ else
+ ret = nor->controller_ops->read_reg(nor, SPINOR_OP_RDSR,
+ sr, 1);
}

if (ret)
@@ -388,6 +401,8 @@ static int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
static int spi_nor_read_fsr(struct spi_nor *nor, u8 *fsr)
{
int ret;
+ u8 addr_bytes = nor->params->rdsr_addr_nbytes;
+ u8 dummy = nor->params->rdsr_dummy;

if (nor->spimem) {
struct spi_mem_op op =
@@ -396,6 +411,12 @@ static int spi_nor_read_fsr(struct spi_nor *nor, u8 *fsr)
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_IN(1, fsr, 1));

+ if (spi_nor_protocol_is_dtr(nor->reg_proto)) {
+ op.addr.nbytes = addr_bytes;
+ op.addr.val = 0;
+ op.dummy.nbytes = dummy;
+ }
+
spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);

ret = spi_mem_exec_op(nor->spimem, &op);
--
2.26.2
\
 
 \ /
  Last update: 2020-05-20 18:32    [W:0.121 / U:0.804 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site