lkml.org 
[lkml]   [2020]   [May]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 3/6] media: ov5647: Add support for non-continuous clock mode
Hi Roman,

On Tue, May 19, 2020 at 04:16:18AM +0300, Roman Kovalivskyi wrote:
> From: Dave Stevenson <dave.stevenson@raspberrypi.org>
>
> The driver was only supporting continuous clock mode
> although this was not stated anywhere.
> Non-continuous clock saves a small amount of power and
> on some SoCs is easier to interface with.
>
> Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
> Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
> ---
> drivers/media/i2c/ov5647.c | 25 ++++++++++++++++++++++---
> 1 file changed, 22 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/media/i2c/ov5647.c b/drivers/media/i2c/ov5647.c
> index 796cc80f8ee1..10f35c637f91 100644
> --- a/drivers/media/i2c/ov5647.c
> +++ b/drivers/media/i2c/ov5647.c
> @@ -44,6 +44,7 @@
> #define PWDN_ACTIVE_DELAY_MS 20
>
> #define MIPI_CTRL00_CLOCK_LANE_GATE BIT(5)
> +#define MIPI_CTRL00_LINE_SYNC_ENABLE BIT(4)
> #define MIPI_CTRL00_BUS_IDLE BIT(2)
> #define MIPI_CTRL00_CLOCK_LANE_DISABLE BIT(0)
>
> @@ -95,6 +96,7 @@ struct ov5647 {
> int power_count;
> struct clk *xclk;
> struct gpio_desc *pwdn;
> + bool is_clock_contiguous;
> };
>
> static inline struct ov5647 *to_state(struct v4l2_subdev *sd)
> @@ -274,9 +276,15 @@ static int ov5647_set_virtual_channel(struct v4l2_subdev *sd, int channel)
>
> static int ov5647_stream_on(struct v4l2_subdev *sd)
> {
> + struct ov5647 *ov5647 = to_state(sd);
> + u8 val = MIPI_CTRL00_BUS_IDLE;
> int ret;
>
> - ret = ov5647_write(sd, OV5647_REG_MIPI_CTRL00, MIPI_CTRL00_BUS_IDLE);
> + if (ov5647->is_clock_contiguous)
> + val |= MIPI_CTRL00_CLOCK_LANE_GATE |
> + MIPI_CTRL00_LINE_SYNC_ENABLE;
> +
> + ret = ov5647_write(sd, OV5647_REG_MIPI_CTRL00, val);
> if (ret < 0)
> return ret;
>
> @@ -573,7 +581,7 @@ static const struct v4l2_subdev_internal_ops ov5647_subdev_internal_ops = {
> .open = ov5647_open,
> };
>
> -static int ov5647_parse_dt(struct device_node *np)
> +static int ov5647_parse_dt(struct ov5647 *sensor, struct device_node *np)
> {
> struct v4l2_fwnode_endpoint bus_cfg = { .bus_type = 0 };
> struct device_node *ep;
> @@ -586,6 +594,17 @@ static int ov5647_parse_dt(struct device_node *np)
>
> ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &bus_cfg);
>

Extra newline.

> + if (!ret) {
> + of_node_put(ep);
> + of_node_put(np);

Why to put np as well?

> + return ret;

Please add a label at the end; it makes error handling easier.

> + }
> +
> + if (bus_cfg.bus_type == V4L2_MBUS_CSI2_DPHY
> + || bus_cfg.bus_type == V4L2_MBUS_CSI2_CPHY)

I bet this device is D-PHY only.

> + sensor->is_clock_contiguous = bus_cfg.bus.mipi_csi2.flags
> + & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK;

Now that you're making use of bus specific parameters, please set the bus
type first before calling v4l2_fwnode_endpoint_parse().

> +
> of_node_put(ep);
> return ret;
> }
> @@ -604,7 +623,7 @@ static int ov5647_probe(struct i2c_client *client)
> return -ENOMEM;
>
> if (IS_ENABLED(CONFIG_OF) && np) {
> - ret = ov5647_parse_dt(np);
> + ret = ov5647_parse_dt(sensor, np);
> if (ret) {
> dev_err(dev, "DT parsing error: %d\n", ret);
> return ret;

--
Kind regards,

Sakari Ailus

\
 
 \ /
  Last update: 2020-05-19 13:58    [W:0.151 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site