lkml.org 
[lkml]   [2020]   [May]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v13 3/5] usb: xhci: Add support for Renesas controller with memory
On 19-05-20, 00:37, Anders Roxell wrote:
> On Mon, 18 May 2020 at 21:57, Vinod Koul <vkoul@kernel.org> wrote:
> >
> > Hi Anders,
>
> Hi Vinod,
>
> >
> > On 18-05-20, 19:53, Anders Roxell wrote:
> > > On Wed, 6 May 2020 at 08:01, Vinod Koul <vkoul@kernel.org> wrote:
> > > >
> > > > Some rensas controller like uPD720201 and uPD720202 need firmware to be
> > > > loaded. Add these devices in pci table and invoke renesas firmware loader
> > > > functions to check and load the firmware into device memory when
> > > > required.
> > > >
> > > > Signed-off-by: Vinod Koul <vkoul@kernel.org>
> > >
> > > Hi, I got a build error when I built an arm64 allmodconfig kernel.
> >
> > Thanks for this. This is happening as we have default y for USB_XHCI_PCI
> > and then we make USB_XHCI_PCI_RENESAS=m. That should be not allowed as
> > we export as symbol so both can be inbuilt or modules but USB_XHCI_PCI=y
> > and USB_XHCI_PCI_RENESAS=m cant. While it is valid that USB_XHCI_PCI=y|m
> > and USB_XHCI_PCI_RENESAS=n
> >
> > So this seems to get fixed by below for me. I have tested with
> > - both y and m (easy)
> > - make USB_XHCI_PCI_RENESAS=n, USB_XHCI_PCI=y|m works
> > - try making USB_XHCI_PCI=y and USB_XHCI_PCI_RENESAS=m, then
> > USB_XHCI_PCI=m by kbuild :)
> > - try making USB_XHCI_PCI=m and USB_XHCI_PCI_RENESAS=y, kbuild gives
> > error prompt that it will be m due to depends
> >
> > Thanks to all the fixes done by Arnd which pointed me to this. Pls
> > verify
>
> I was able to build an arm64 allmodconfig kernel with this change.

I will send the formal patch and add your name in reported and
tested. Thanks for the quick verification

>
> Cheers,
> Anders
>
> > and I will send the fix with you as reported :)
> >
> > ---- >8 ----
> >
> > diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> > index b5c542d6a1c5..92783d175b3f 100644
> > --- a/drivers/usb/host/Kconfig
> > +++ b/drivers/usb/host/Kconfig
> > @@ -40,11 +40,11 @@ config USB_XHCI_DBGCAP
> > config USB_XHCI_PCI
> > tristate
> > depends on USB_PCI
> > + depends on USB_XHCI_PCI_RENESAS || !USB_XHCI_PCI_RENESAS
> > default y
> >
> > config USB_XHCI_PCI_RENESAS
> > tristate "Support for additional Renesas xHCI controller with firwmare"
> > - depends on USB_XHCI_PCI
> > ---help---
> > Say 'Y' to enable the support for the Renesas xHCI controller with
> > firwmare. Make sure you have the firwmare for the device and
> >
> > --
> > ~Vinod

--
~Vinod

\
 
 \ /
  Last update: 2020-05-19 06:54    [W:0.068 / U:0.732 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site