lkml.org 
[lkml]   [2020]   [May]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC PATCH 6/6] arm64: dts: imx8mq-librem5-devkit: Enable MIPI DSI panel
Date
Enable MIPI LCD panel output by adding nodes for the NWL DSI host
controller, the mux-input-bridge, the Rocktech panel and the eLCDIF
display controller.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
.../dts/freescale/imx8mq-librem5-devkit.dts | 81 +++++++++++++++++++
1 file changed, 81 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 7fc31c71a626..d98f9b8dede8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -841,6 +841,87 @@ MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x19 /* WWAN_RESET */
};
};

+&lcdif {
+ status = "okay";
+
+ port@0 {
+ lcdif_dpi_out: endpoint {
+ remote-endpoint = <&dpi_mux_from_lcdif>;
+ };
+ };
+};
+
+&iomuxc_gpr {
+ mipi_mux: mipi-mux {
+ compatible = "mux-input-bridge";
+ mux-controls = <&mux 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+ default-input = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ dpi_mux_from_lcdif: endpoint {
+ remote-endpoint = <&lcdif_dpi_out>;
+ };
+ };
+
+ port@1 { /* dcss */
+ reg = <1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ dpi_mux_out: endpoint {
+ remote-endpoint = <&nwl_dpi_in>;
+ };
+
+ };
+ };
+ };
+};
+
+&mipi_dsi {
+ status = "okay";
+ panel@0 {
+ compatible = "rocktech,jh057n00900";
+ reg = <0>;
+ backlight = <&backlight_dsi>;
+ reset-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&reg_2v8_p>;
+ iovcc-supply = <&reg_1v8_p>;
+ port@0 {
+ panel_in: endpoint {
+ remote-endpoint = <&nwl_dsi_out>;
+ };
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ nwl_dpi_in: endpoint {
+ remote-endpoint = <&dpi_mux_out>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ nwl_dsi_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
&pgc_gpu {
power-supply = <&buck3_reg>;
};
--
2.26.1
\
 
 \ /
  Last update: 2020-05-15 15:12    [W:0.097 / U:0.520 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site