lkml.org 
[lkml]   [2020]   [May]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net-next v1] net: phy: tja11xx: execute cable test on link up
Date
A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be able
to automatically handle this issue, but we need to log it or notify user
(if possible).

With this patch, the cable will be tested on "ip l s dev .. up" attempt
and send ethnl notification to the user space.

This patch was tested with TJA1102 PHY and "ethtool --monitor" command.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/net/phy/nxp-tja11xx.c | 48 +++++++++++++++++++++++++++++++----
1 file changed, 43 insertions(+), 5 deletions(-)

diff --git a/drivers/net/phy/nxp-tja11xx.c b/drivers/net/phy/nxp-tja11xx.c
index 8b743d25002b9..0d4f9067ca715 100644
--- a/drivers/net/phy/nxp-tja11xx.c
+++ b/drivers/net/phy/nxp-tja11xx.c
@@ -180,10 +180,43 @@ static int tja11xx_soft_reset(struct phy_device *phydev)
return genphy_soft_reset(phydev);
}

+static int tja11xx_config_aneg_cable_test(struct phy_device *phydev)
+{
+ bool finished = false;
+ int ret;
+
+ if (phydev->link)
+ return 0;
+
+ if (!phydev->drv->cable_test_start ||
+ !phydev->drv->cable_test_get_status)
+ return 0;
+
+ ret = ethnl_cable_test_alloc(phydev);
+ if (ret)
+ return ret;
+
+ ret = phydev->drv->cable_test_start(phydev);
+ if (ret)
+ return ret;
+
+ /* According to the documentation this test takes 100 usec */
+ usleep_range(100, 200);
+
+ ret = phydev->drv->cable_test_get_status(phydev, &finished);
+ if (ret)
+ return ret;
+
+ if (finished)
+ ethnl_cable_test_finished(phydev);
+
+ return 0;
+}
+
static int tja11xx_config_aneg(struct phy_device *phydev)
{
+ int ret, changed = 0;
u16 ctl = 0;
- int ret;

switch (phydev->master_slave_set) {
case MASTER_SLAVE_CFG_MASTER_FORCE:
@@ -193,17 +226,22 @@ static int tja11xx_config_aneg(struct phy_device *phydev)
break;
case MASTER_SLAVE_CFG_UNKNOWN:
case MASTER_SLAVE_CFG_UNSUPPORTED:
- return 0;
+ goto do_test;
default:
phydev_warn(phydev, "Unsupported Master/Slave mode\n");
return -ENOTSUPP;
}

- ret = phy_modify_changed(phydev, MII_CFG1, MII_CFG1_MASTER_SLAVE, ctl);
- if (ret < 0)
+ changed = phy_modify_changed(phydev, MII_CFG1, MII_CFG1_MASTER_SLAVE, ctl);
+ if (changed < 0)
+ return changed;
+
+do_test:
+ ret = tja11xx_config_aneg_cable_test(phydev);
+ if (ret)
return ret;

- return __genphy_config_aneg(phydev, ret);
+ return __genphy_config_aneg(phydev, changed);
}

static int tja11xx_config_init(struct phy_device *phydev)
--
2.26.2
\
 
 \ /
  Last update: 2020-05-14 21:43    [W:0.113 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site