lkml.org 
[lkml]   [2020]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [EXT] [PATCH 09/15] qed: use new module_firmware_crashed()
On Tue, May 12, 2020 at 07:23:28PM +0300, Igor Russkikh wrote:
>
> >> So I think its not a good place to insert this call.
> >> Its hard to find exact good place to insert it in qed.
> >
> > Is there a way to check if what happened was indeed a fw crash?
>
> Our driver has two firmwares (slowpath and fastpath).
> For slowpath firmware the way to understand it crashed is to observe command
> response timeout. This is in qed_mcp.c, around "The MFW failed to respond to
> command" traceout.

Ok thanks.

> For fastpath this is tricky, think you may leave the above place as the only
> place to invoke module_firmware_crashed()

So do you mean like the changes below?

diff --git a/drivers/net/ethernet/qlogic/qed/qed_debug.c b/drivers/net/ethernet/qlogic/qed/qed_debug.c
index f4eebaabb6d0..95cb7da2542e 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_debug.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_debug.c
@@ -7906,6 +7906,7 @@ int qed_dbg_all_data(struct qed_dev *cdev, void *buffer)
rc = qed_dbg_grc(cdev, (u8 *)buffer + offset +
REGDUMP_HEADER_SIZE, &feature_size);
if (!rc) {
+ module_firmware_crashed();
*(u32 *)((u8 *)buffer + offset) =
qed_calc_regdump_header(cdev, GRC_DUMP,
cur_engine,
diff --git a/drivers/net/ethernet/qlogic/qed/qed_mcp.c b/drivers/net/ethernet/qlogic/qed/qed_mcp.c
index 280527cc0578..a818cf09dccf 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_mcp.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.c
@@ -566,6 +566,7 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *p_hwfn,
DP_NOTICE(p_hwfn,
"The MFW failed to respond to command 0x%08x [param 0x%08x].\n",
p_mb_params->cmd, p_mb_params->param);
+ module_firmware_crashed();
qed_mcp_print_cpu_info(p_hwfn, p_ptt);

spin_lock_bh(&p_hwfn->mcp_info->cmd_lock);
> >> One more thing is that AFAIU taint flag gets permanent on kernel, but
> > for
> >> example our device can recover itself from some FW crashes, thus it'd be
> >> transparent for user.
> >
> > Similar things are *supposed* to recoverable with other device, however
> > this can also sometimes lead to a situation where devices are not usable
> > anymore, and require a full driver unload / load.
> >
> >> Whats the logical purpose of module_firmware_crashed? Does it mean fatal
> >> unrecoverable error on device?
> >
> > Its just to annotate on the module and kernel that this has happened.
> >
> > I take it you may agree that, firmware crashing *often* is not good
> > design,
> > and these issues should be reported to / fixed by vendors. In cases
> > where driver bugs are reported it is good to see if a firmware crash has
> > happened before, so that during analysis this is ruled out.
>
> Probably, but still I see some misalignment here, in sense that taint is about
> the kernel state, not about a hardware state indication.

The kernel carries the driver though, and the driver / subsystem can
often times act strange when this happens.

> devlink health could really be a much better candidate for such things.

That sounds fantastic, please Cc me on patches! However I still believe
we should register this event in the kernel for support purposes.

Luis

\
 
 \ /
  Last update: 2020-05-12 19:34    [W:0.075 / U:0.588 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site