lkml.org 
[lkml]   [2020]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 4/6] dmaengine: dw: Print warning if multi-block is unsupported
Vinod,

Could you join the discussion for a little bit?

In order to properly fix the problem discussed in this topic, we need to
introduce an additional capability exported by DMA channel handlers on per-channel
basis. It must be a number, which would indicate an upper limitation of the SG list
entries amount.
Something like this would do it:
struct dma_slave_caps {
...
unsigned int max_sg_nents;
...
};
As Andy suggested it's value should be interpreted as:
0 - unlimited number of entries,
1:MAX_UINT - actual limit to the number of entries.

In addition to that seeing the dma_get_slave_caps() method provide the caps only
by getting them from the DMA device descriptor, while we need to have an info on
per-channel basis, it would be good to introduce a new DMA-device callback like:
struct dma_device {
...
int (*device_caps)(struct dma_chan *chan,
struct dma_slave_caps *caps);
...
};
So the DMA driver could override the generic DMA device capabilities with the
values specific to the DMA channels. Such functionality will be also helpful for
the max-burst-len parameter introduced by this patchset, since depending on the
IP-core synthesis parameters it may be channel-specific.

Alternatively we could just introduce a new fields to the dma_chan structure and
retrieve the new caps values from them in the dma_get_slave_caps() method.
Though the solution with callback I like better.

What is your opinion about this? What solution you'd prefer?

On Tue, May 12, 2020 at 12:08:00AM +0300, Andy Shevchenko wrote:
> On Tue, May 12, 2020 at 12:07:14AM +0300, Andy Shevchenko wrote:
> > On Mon, May 11, 2020 at 10:32:55PM +0300, Serge Semin wrote:
> > > On Mon, May 11, 2020 at 04:58:53PM +0300, Andy Shevchenko wrote:
> > > > On Mon, May 11, 2020 at 4:48 PM Serge Semin
> > > > <Sergey.Semin@baikalelectronics.ru> wrote:
> > > > >
> > > > > On Mon, May 11, 2020 at 12:58:13PM +0100, Mark Brown wrote:
> > > > > > On Mon, May 11, 2020 at 05:10:16AM +0300, Serge Semin wrote:
> > > > > >
> > > > > > > Alas linearizing the SPI messages won't help in this case because the DW DMA
> > > > > > > driver will split it into the max transaction chunks anyway.
> > > > > >
> > > > > > That sounds like you need to also impose a limit on the maximum message
> > > > > > size as well then, with that you should be able to handle messages up
> > > > > > to whatever that limit is. There's code for that bit already, so long
> > > > > > as the limit is not too low it should be fine for most devices and
> > > > > > client drivers can see the limit so they can be updated to work with it
> > > > > > if needed.
> > > > >
> > > > > Hmm, this might work. The problem will be with imposing such limitation through
> > > > > the DW APB SSI driver. In order to do this I need to know:
> > > > > 1) Whether multi-block LLP is supported by the DW DMA controller.
> > > > > 2) Maximum DW DMA transfer block size.
> > > > > Then I'll be able to use this information in the can_dma() callback to enable
> > > > > the DMA xfers only for the safe transfers. Did you mean something like this when
> > > > > you said "There's code for that bit already" ? If you meant the max_dma_len
> > > > > parameter, then setting it won't work, because it just limits the SG items size
> > > > > not the total length of a single transfer.
> > > > >
> > > > > So the question is of how to export the multi-block LLP flag from DW DMAc
> > > > > driver. Andy?
> > > >
> > > > I'm not sure I understand why do you need this being exported. Just
> > > > always supply SG list out of single entry and define the length
> > > > according to the maximum segment size (it's done IIRC in SPI core).
> > >
> > > Finally I see your point. So you suggest to feed the DMA engine with SG list
> > > entries one-by-one instead of sending all of them at once in a single
> > > dmaengine_prep_slave_sg() -> dmaengine_submit() -> dma_async_issue_pending()
> > > session. Hm, this solution will work, but there is an issue. There is no
> > > guarantee, that Tx and Rx SG lists are symmetric, consisting of the same
> > > number of items with the same sizes. It depends on the Tx/Rx buffers physical
> > > address alignment and their offsets within the memory pages. Though this
> > > problem can be solved by making the Tx and Rx SG lists symmetric. I'll have
> > > to implement a clever DMA IO loop, which would extract the DMA
> > > addresses/lengths from the SG entries and perform the single-buffer DMA
> > > transactions with the DMA buffers of the same length.
> > >
> > > Regarding noLLP being exported. Obviously I intended to solve the problem in a
> > > generic way since the problem is common for noLLP DW APB SSI/DW DMAC combination.
> > > In order to do this we need to know whether the multi-block LLP feature is
> > > unsupported by the DW DMA controller. We either make such info somehow exported
> > > from the DW DMA driver, so the DMA clients (like Dw APB SSI controller driver)
> > > could be ready to work around the problem; or just implement a flag-based quirk
> > > in the DMA client driver, which would be enabled in the platform-specific basis
> > > depending on the platform device actually detected (for instance, a specific
> > > version of the DW APB SSI IP). AFAICS You'd prefer the later option.
> >
> > So, we may extend the struct of DMA parameters to tell the consumer amount of entries (each of which is no longer than maximum segment size) it can afford:
> > - 0: Auto (DMA driver handles any cases itself)
> > - 1: Only single entry
> > - 2: Up to two...
>
> It will left implementation details (or i.o.w. obstacles or limitation) why DMA
> can't do otherwise.

Sounds good. Thanks for assistance.

-Sergey

>
> --
> With Best Regards,
> Andy Shevchenko
>
>

\
 
 \ /
  Last update: 2020-05-12 14:42    [W:0.152 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site