lkml.org 
[lkml]   [2020]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ARM: dts: imx6qdl-gw5910: add support for bcm4330-bt
Date
The Sterling-LWB has a BCM4330 which has a UART based bluetooth
HCI. Add support for binding to the bcm_hci driver to take care
of handling the shutdown gpio and loading firmware.

Because the shutdown gpio is more of an enable than a regulator
go ahead and replace the regulator with a shutdown-gpio.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
arch/arm/boot/dts/imx6qdl-gw5910.dtsi | 32 ++++++++++++--------------------
1 file changed, 12 insertions(+), 20 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
index 30fe47f..b850f8f 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
@@ -83,19 +83,6 @@
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
-
- reg_bt: regulator-bt {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_bt>;
- compatible = "regulator-fixed";
- regulator-name = "bt";
- gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
- startup-delay-us = <100>;
- enable-active-high;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
};


@@ -231,9 +218,14 @@
/* Sterling-LWB Bluetooth */
&uart4 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
+ pinctrl-0 = <&pinctrl_uart4>,<&pinctrl_bten>;
uart-has-rtscts;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4330-bt";
+ shutdown-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ };
};

/* GPS */
@@ -288,6 +280,12 @@
>;
};

+ pinctrl_bten: btengrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1
+ >;
+ };
+
pinctrl_ecspi3: escpi3grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
@@ -393,12 +391,6 @@
>;
};

- pinctrl_reg_bt: regbtgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1
- >;
- };
-
pinctrl_reg_wl: regwlgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b1
--
2.7.4
\
 
 \ /
  Last update: 2020-05-12 23:54    [W:0.035 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site