lkml.org 
[lkml]   [2020]   [May]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 05/16] mfd: Add support for Kontron sl28cpld management controller
Am 2020-05-11 23:13, schrieb Rob Herring:
> On Thu, Apr 23, 2020 at 07:45:32PM +0200, Michael Walle wrote:
>> This patch adds core support for the board management controller found
>> on the SMARC-sAL28 board. It consists of the following functions:
>> - watchdog
>> - GPIO controller
>> - PWM controller
>> - fan sensor
>> - interrupt controller
>>
>> At the moment, this controller is used on the Kontron SMARC-sAL28
>> board.
>>
>> Please note that the MFD driver is defined as bool in the Kconfig
>> because the next patch will add interrupt support.
>>
>> Signed-off-by: Michael Walle <michael@walle.cc>
>> ---
>> drivers/mfd/Kconfig | 19 +++++
>> drivers/mfd/Makefile | 2 +
>> drivers/mfd/sl28cpld.c | 153
>> +++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 174 insertions(+)
>> create mode 100644 drivers/mfd/sl28cpld.c
>>
>> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
>> index 0a59249198d3..be0c8d93c526 100644
>> --- a/drivers/mfd/Kconfig
>> +++ b/drivers/mfd/Kconfig
>> @@ -2060,5 +2060,24 @@ config SGI_MFD_IOC3
>> If you have an SGI Origin, Octane, or a PCI IOC3 card,
>> then say Y. Otherwise say N.
>>
>> +config MFD_SL28CPLD
>> + bool "Kontron sl28 core driver"
>> + depends on I2C=y
>> + depends on OF
>> + select REGMAP_I2C
>> + select MFD_CORE
>> + help
>> + This option enables support for the board management controller
>> + found on the Kontron sl28 CPLD. You have to select individual
>> + functions, such as watchdog, GPIO, etc, under the corresponding
>> menus
>> + in order to enable them.
>> +
>> + Currently supported boards are:
>> +
>> + Kontron SMARC-sAL28
>> +
>> + To compile this driver as a module, choose M here: the module will
>> be
>> + called sl28cpld.
>> +
>> endmenu
>> endif
>> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
>> index f935d10cbf0f..9bc38863b9c7 100644
>> --- a/drivers/mfd/Makefile
>> +++ b/drivers/mfd/Makefile
>> @@ -259,3 +259,5 @@ obj-$(CONFIG_MFD_ROHM_BD718XX) += rohm-bd718x7.o
>> obj-$(CONFIG_MFD_STMFX) += stmfx.o
>>
>> obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o
>> +
>> +obj-$(CONFIG_MFD_SL28CPLD) += sl28cpld.o
>> diff --git a/drivers/mfd/sl28cpld.c b/drivers/mfd/sl28cpld.c
>> new file mode 100644
>> index 000000000000..1e5860cc7ffc
>> --- /dev/null
>> +++ b/drivers/mfd/sl28cpld.c
>> @@ -0,0 +1,153 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * MFD core for the sl28cpld.
>> + *
>> + * Copyright 2019 Kontron Europe GmbH
>> + */
>> +
>> +#include <linux/i2c.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/kernel.h>
>> +#include <linux/mfd/core.h>
>> +#include <linux/module.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/regmap.h>
>> +
>> +#define SL28CPLD_VERSION 0x03
>> +#define SL28CPLD_WATCHDOG_BASE 0x04
>> +#define SL28CPLD_HWMON_FAN_BASE 0x0b
>> +#define SL28CPLD_PWM0_BASE 0x0c
>> +#define SL28CPLD_PWM1_BASE 0x0e
>> +#define SL28CPLD_GPIO0_BASE 0x10
>> +#define SL28CPLD_GPIO1_BASE 0x15
>> +#define SL28CPLD_GPO_BASE 0x1a
>> +#define SL28CPLD_GPI_BASE 0x1b
>> +#define SL28CPLD_INTC_BASE 0x1c
>
> If you want to use 'reg' in the binding, these are the numbers you
> should be using rather than making up numbering!

My motivation is that I don't want to hardcode the internal addresses
of the management controller in the device tree. For example if they
will move around with a later update of the controller, so a driver can
be compatible with both the old and the new version. If they are in the
device tree, only one register layout is possible.

> However, I still don't think you need any child nodes. All the data in
> the DT binding is right here in the driver already. There's no
> advantage
> to putting child nodes in DT, because this driver still has to be
> updated if you add more nodes.

But then any phandle will reference the mfd device. And for example
there
are two different interrupt controllers, that is the INTC and the
GPIO[01],
which will then be combined into one device tree node, right?

So the mfd node would be

cpld: sl28cpld@4a {
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
[..]
};

and then depending on the mapping one could use:

interrupts-extended = <&cpld 0 FLAGS>; /* gpio0 line 0 */
interrupts-extended = <&cpld 8 FLAGS>; /* gpio1 line 0 */
interrupts-extended = <&cpld 12 FLAGS>; /* irq0 */

gpios = <&cpld 0> /* gpio0 line 0 */

But there is also offset 12, but then it is the GPI controller:

gpios = <&cpld 12> /* gpi line 0, nothing to do with irq0 */

I don't know if this is good practice, I guess you have to tell me. And
is it possible to combine any sub device into the mfd node in that way?

-michael

\
 
 \ /
  Last update: 2020-05-11 23:45    [W:0.137 / U:1.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site