lkml.org 
[lkml]   [2020]   [May]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 0/5] mtd: spi-nor: Add support for Octal 8D-8D-8D mode
From
Date

Hi Vignesh,

> >>>
> >>> Our mx25uw51245g supports BFPT DWORD-18,19 and 20 data and xSPI
> > profile
> >>> 1.0,
> >>> and it comply with BFPT DWORD-19, octal mode enable sequences by
write
> > CFG
> >>> Reg2
> >>> with instruction 0x72. Therefore, I can't apply your patches.
> >>
> >> I didn't mean apply my patches directly. I meant more along the lines
of
> >
> >> edit your patches to work on top of my series. It should be as easy
as
> >> adding your flash's fixup hooks and its octal DTR enable hook, but if
my
> >
> >> series is missing something you need (like complete Profile 1.0
parsing,
> >
> >> which I left out because I wanted to be conservative and didn't see
any
> >> immediate use-case for us), let me know, and we can work together to
> >> address it.
> >
> > yes,sure!
> > let's work together to upstream the Octal 8D-8D-8D driver to mainline.
> >
> > The main concern is where and how to enable xSPI octal mode?
> >
> > Vignesh don't agree to enable it in fixup hooks and that's why I
patched
> > it to spi_nor_late_init_params() and confirmed the device support xSPI

> > Octal mode after BFPT DWORD-19 and xSPI pf 1.0 have been parsed.
> >
>
> My suggestion was to use SFDP wherever possible.. E.g: it is possible to
> get opcode extension type from BFPT...
>
> But using BFPT DWORD-19 is not correct for switching to 8D-8D-8D mode:
>
> Per JESD216D.01 Bits 22:20 of 19th DWORD of BFPT:
>
> Octal Enable Requirements:
>
> This field describes whether the device contains a Octal Enable bit used
> to enable 1-1-8 and 1-
> 8-8 octal read or octal program operations.
>
> So, this cannot be used for enabling 8D-8D-8D mode... Flashes that only
> support 1S-1S-1S and 8D-8D-8D will set this field to 0.

yes, you are right, the bits 22~20 your mentioned are for 1-1-8 and 1-8-8
mode enable requirements and they are zero if Flash only supports
1S-1S-1S,
8S-8S-8S and 8D-8D-8D, just like mx25xx series.

There are bits 8~4 for 8S-8S-8S and 8D-8D-8D mode enable sequences and
I have patched these in this patches.

By bits 8~4 in 19 th DWORD of BFPT, driver will know enable 8S-8S-8S or
8D-8D-8D by either issue two instruction (06h and E8h) or
by Write CFG Reg 2.

mx25xx series supports enable Octal 8S-8S-8S/8D-8D-8D mode by Write CFG
Reg 2.


>
> There is a separate table to enable 8D mode called
> "Command Sequences to Change to Octal DDR (8D-8D-8D) mode". But if flash
> does not have the table or has bad data, fixup hook is the only way...
>
> If mx25* supports above table, please build on top of Pratyush's series
> to add support for parsing this table. Otherwise, macronix would have to
> use a fixup hook too...

mx25xx series also supports "Command Sequences to Change to Octal DDR
(8D-8D-8D) mode" for sure. I will patch them in next version.

For mx25* series, a fixup hook will only setup specific dummy cycles to
device for various frequency after xSPI 1.0 table has been parsed.


thanks for your time & comments.
Mason


CONFIDENTIALITY NOTE:

This e-mail and any attachments may contain confidential information
and/or personal data, which is protected by applicable laws. Please be
reminded that duplication, disclosure, distribution, or use of this e-mail
(and/or its attachments) or any part thereof is prohibited. If you receive
this e-mail in error, please notify us immediately and delete this mail as
well as its attachment(s) from your system. In addition, please be
informed that collection, processing, and/or use of personal data is
prohibited unless expressly permitted by personal data protection laws.
Thank you for your attention and cooperation.

Macronix International Co., Ltd.

=====================================================================



============================================================================

CONFIDENTIALITY NOTE:

This e-mail and any attachments may contain confidential information and/or personal data, which is protected by applicable laws. Please be reminded that duplication, disclosure, distribution, or use of this e-mail (and/or its attachments) or any part thereof is prohibited. If you receive this e-mail in error, please notify us immediately and delete this mail as well as its attachment(s) from your system. In addition, please be informed that collection, processing, and/or use of personal data is prohibited unless expressly permitted by personal data protection laws. Thank you for your attention and cooperation.

Macronix International Co., Ltd.

=====================================================================

\
 
 \ /
  Last update: 2020-05-11 05:24    [W:0.129 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site