lkml.org 
[lkml]   [2020]   [May]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4.4 35/70] USB: hub: Fix handling of connect changes during sleep
Date
From: Alan Stern <stern@rowland.harvard.edu>

commit 9f952e26295d977dbfc6fedeaf8c4f112c818d37 upstream.

Commit 8099f58f1ecd ("USB: hub: Don't record a connect-change event
during reset-resume") wasn't very well conceived. The problem it
tried to fix was that if a connect-change event occurred while the
system was asleep (such as a device disconnecting itself from the bus
when it is suspended and then reconnecting when it resumes)
requiring a reset-resume during the system wakeup transition, the hub
port's change_bit entry would remain set afterward. This would cause
the hub driver to believe another connect-change event had occurred
after the reset-resume, which was wrong and would lead the driver to
send unnecessary requests to the device (which could interfere with a
firmware update).

The commit tried to fix this by not setting the change_bit during the
wakeup. But this was the wrong thing to do; it means that when a
device is unplugged while the system is asleep, the hub driver doesn't
realize anything has happened: The change_bit flag which would tell it
to handle the disconnect event is clear.

The commit needs to be reverted and the problem fixed in a different
way. Fortunately an alternative solution was noted in the commit's
Changelog: We can continue to set the change_bit entry in
hub_activate() but then clear it when a reset-resume occurs. That way
the the hub driver will see the change_bit when a device is
disconnected but won't see it when the device is still present.

That's what this patch does.

Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8099f58f1ecd ("USB: hub: Don't record a connect-change event during reset-resume")
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221602480.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
drivers/usb/core/hub.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)

--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1175,6 +1175,11 @@ static void hub_activate(struct usb_hub
#ifdef CONFIG_PM
udev->reset_resume = 1;
#endif
+ /* Don't set the change_bits when the device
+ * was powered off.
+ */
+ if (test_bit(port1, hub->power_bits))
+ set_bit(port1, hub->change_bits);

} else {
/* The power session is gone; tell hub_wq */
@@ -2939,6 +2944,15 @@ static int check_port_resume_type(struct
if (portchange & USB_PORT_STAT_C_ENABLE)
usb_clear_port_feature(hub->hdev, port1,
USB_PORT_FEAT_C_ENABLE);
+
+ /*
+ * Whatever made this reset-resume necessary may have
+ * turned on the port1 bit in hub->change_bits. But after
+ * a successful reset-resume we want the bit to be clear;
+ * if it was on it would indicate that something happened
+ * following the reset-resume.
+ */
+ clear_bit(port1, hub->change_bits);
}

return status;

\
 
 \ /
  Last update: 2020-05-01 15:26    [W:0.288 / U:0.396 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site