lkml.org 
[lkml]   [2020]   [May]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 02/13] arm: dts: s5pv210: fascinate4g: Add sleep GPIO configuration
On Tue, Apr 28, 2020 at 04:49:36PM -0700, Jonathan Bakker wrote:
> Hi Krzysztof,
>
> On 2020-04-28 3:02 a.m., Krzysztof Kozlowski wrote:
> > On Sun, Apr 26, 2020 at 11:35:53AM -0700, Jonathan Bakker wrote:
> >> In order to minimize leakage current during sleep, set a config
> >> for sleep GPIOs.
> >>
> >> Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
> >> ---
> >> arch/arm/boot/dts/s5pv210-fascinate4g.dts | 242 ++++++++++++++++++++++
> >> 1 file changed, 242 insertions(+)
> >>
> >> diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
> >> index 07a8d9bbe5b8..94dcb9b64b9a 100644
> >> --- a/arch/arm/boot/dts/s5pv210-fascinate4g.dts
> >> +++ b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
> >> @@ -36,3 +36,245 @@
> >> };
> >> };
> >> };
> >> +
> >> +&pinctrl0 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&sleep_cfg>;
> >> +
> >> + sleep_cfg: sleep-cfg {
> >> + PIN_SLP(gpa0-0, PREV, NONE);
> >> + PIN_SLP(gpa0-1, PREV, NONE);
> >> + PIN_SLP(gpa0-2, PREV, NONE);
> >> + PIN_SLP(gpa0-3, OUT1, NONE);
> >
> > I would be happy to see some reasoning why certain pins have disabled
> > pull down (e.g. they are not connected or you use the same configuration
> > as running one) and why you set them as output.
> >
>
> Mostly it's copied from the vendor kernel configuration. Without schematics, I can
> only guess what's actually there. I can go through and note what each pin appears
> to be used for if you'd like.

Then please mention that it is based on vendor kernel vx.y for product
ABC. In such case it will be enough.

>
> >> + PIN_SLP(gpa0-4, PREV, NONE);
> >> + PIN_SLP(gpa0-5, PREV, NONE);
> >> + PIN_SLP(gpa0-6, PREV, NONE);
> >> + PIN_SLP(gpa0-7, PREV, NONE);
> >> +
> >> + PIN_SLP(gpa1-0, INPUT, DOWN);
> >> + PIN_SLP(gpa1-1, OUT0, NONE);
> >> + PIN_SLP(gpa1-2, INPUT, DOWN);
> >> + PIN_SLP(gpa1-3, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpb-0, OUT0, NONE);
> >> + PIN_SLP(gpb-1, OUT1, NONE);
> >> + PIN_SLP(gpb-2, OUT0, NONE);
> >> + PIN_SLP(gpb-3, PREV, NONE);
> >> + PIN_SLP(gpb-4, INPUT, NONE);
> >> + PIN_SLP(gpb-5, PREV, NONE);
> >> + PIN_SLP(gpb-6, INPUT, DOWN);
> >> + PIN_SLP(gpb-7, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpc0-0, OUT0, NONE);
> >> + PIN_SLP(gpc0-1, INPUT, DOWN);
> >> + PIN_SLP(gpc0-2, OUT0, NONE);
> >> + PIN_SLP(gpc0-3, INPUT, DOWN);
> >> + PIN_SLP(gpc0-4, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpc1-0, INPUT, DOWN);
> >> + PIN_SLP(gpc1-1, INPUT, DOWN);
> >> + PIN_SLP(gpc1-2, INPUT, DOWN);
> >> + PIN_SLP(gpc1-3, INPUT, DOWN);
> >> + PIN_SLP(gpc1-4, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpd0-0, INPUT, DOWN);
> >> + PIN_SLP(gpd0-1, OUT0, NONE);
> >> + PIN_SLP(gpd0-2, INPUT, DOWN);
> >> + PIN_SLP(gpd0-3, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpd1-0, INPUT, NONE);
> >> + PIN_SLP(gpd1-1, INPUT, NONE);
> >> + PIN_SLP(gpd1-2, INPUT, DOWN);
> >> + PIN_SLP(gpd1-3, INPUT, DOWN);
> >> + PIN_SLP(gpd1-4, INPUT, DOWN);
> >> + PIN_SLP(gpd1-5, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpe0-0, INPUT, DOWN);
> >> + PIN_SLP(gpe0-1, INPUT, DOWN);
> >> + PIN_SLP(gpe0-2, INPUT, DOWN);
> >> + PIN_SLP(gpe0-3, INPUT, DOWN);
> >> + PIN_SLP(gpe0-4, INPUT, DOWN);
> >> + PIN_SLP(gpe0-5, INPUT, DOWN);
> >> + PIN_SLP(gpe0-6, INPUT, DOWN);
> >> + PIN_SLP(gpe0-7, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpe1-0, INPUT, DOWN);
> >> + PIN_SLP(gpe1-1, INPUT, DOWN);
> >> + PIN_SLP(gpe1-2, INPUT, DOWN);
> >> + PIN_SLP(gpe1-3, OUT0, NONE);
> >> + PIN_SLP(gpe1-4, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpf0-0, OUT0, NONE);
> >> + PIN_SLP(gpf0-1, OUT0, NONE);
> >> + PIN_SLP(gpf0-2, OUT0, NONE);
> >> + PIN_SLP(gpf0-3, OUT0, NONE);
> >> + PIN_SLP(gpf0-4, OUT0, NONE);
> >> + PIN_SLP(gpf0-5, OUT0, NONE);
> >> + PIN_SLP(gpf0-6, OUT0, NONE);
> >> + PIN_SLP(gpf0-7, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpf1-0, OUT0, NONE);
> >> + PIN_SLP(gpf1-1, OUT0, NONE);
> >> + PIN_SLP(gpf1-2, OUT0, NONE);
> >> + PIN_SLP(gpf1-3, OUT0, NONE);
> >> + PIN_SLP(gpf1-4, OUT0, NONE);
> >> + PIN_SLP(gpf1-5, OUT0, NONE);
> >> + PIN_SLP(gpf1-6, OUT0, NONE);
> >> + PIN_SLP(gpf1-7, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpf2-0, OUT0, NONE);
> >> + PIN_SLP(gpf2-1, OUT0, NONE);
> >> + PIN_SLP(gpf2-2, OUT0, NONE);
> >> + PIN_SLP(gpf2-3, OUT0, NONE);
> >> + PIN_SLP(gpf2-4, OUT0, NONE);
> >> + PIN_SLP(gpf2-5, OUT0, NONE);
> >> + PIN_SLP(gpf2-6, OUT0, NONE);
> >> + PIN_SLP(gpf2-7, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpf3-0, OUT0, NONE);
> >> + PIN_SLP(gpf3-1, OUT0, NONE);
> >> + PIN_SLP(gpf3-2, OUT0, NONE);
> >> + PIN_SLP(gpf3-3, OUT0, NONE);
> >> + PIN_SLP(gpf3-4, PREV, NONE);
> >> + PIN_SLP(gpf3-5, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpg0-0, INPUT, DOWN);
> >> + PIN_SLP(gpg0-1, INPUT, DOWN);
> >> + PIN_SLP(gpg0-2, INPUT, NONE);
> >> + PIN_SLP(gpg0-3, INPUT, DOWN);
> >> + PIN_SLP(gpg0-4, INPUT, DOWN);
> >> + PIN_SLP(gpg0-5, INPUT, DOWN);
> >> + PIN_SLP(gpg0-6, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpg1-0, OUT0, NONE);
> >> + PIN_SLP(gpg1-1, OUT1, NONE);
> >> + PIN_SLP(gpg1-2, PREV, NONE);
> >> + PIN_SLP(gpg1-3, OUT1, NONE);
> >> + PIN_SLP(gpg1-4, OUT1, NONE);
> >> + PIN_SLP(gpg1-5, OUT1, NONE);
> >> + PIN_SLP(gpg1-6, OUT1, NONE);
> >> +
> >> + PIN_SLP(gpg2-0, OUT0, NONE);
> >> + PIN_SLP(gpg2-1, OUT0, NONE);
> >> + PIN_SLP(gpg2-2, INPUT, NONE);
> >> + PIN_SLP(gpg2-3, OUT0, NONE);
> >> + PIN_SLP(gpg2-4, OUT0, NONE);
> >> + PIN_SLP(gpg2-5, OUT0, NONE);
> >> + PIN_SLP(gpg2-6, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpg3-0, PREV, UP);
> >> + PIN_SLP(gpg3-1, PREV, UP);
> >> + PIN_SLP(gpg3-2, INPUT, NONE);
> >> + PIN_SLP(gpg3-3, INPUT, DOWN);
> >> + PIN_SLP(gpg3-4, OUT0, NONE);
> >> + PIN_SLP(gpg3-5, OUT0, NONE);
> >> + PIN_SLP(gpg3-6, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpi-0, PREV, NONE);
> >
> > No such name. Did you mean gpgi?
> >
> >
>
> The node in s5pv210-pinctrl.dtsi is called "gpgi", but the i2s0_bus config
> in that file uses just "gpi". drivers/pinctrl/samsung/pinctrl-exynos-arm.c also
> notes it just as "gpi". I think the node should probably be renamed.
>

Good point. Will you send a fix for gpgi->gpi?

> >> + PIN_SLP(gpi-1, INPUT, DOWN);
> >> + PIN_SLP(gpi-2, PREV, NONE);
> >> + PIN_SLP(gpi-3, PREV, NONE);
> >> + PIN_SLP(gpi-4, PREV, NONE);
> >> + PIN_SLP(gpi-5, INPUT, DOWN);
> >> + PIN_SLP(gpi-6, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpj0-0, INPUT, NONE);
> >> + PIN_SLP(gpj0-1, INPUT, NONE);
> >> + PIN_SLP(gpj0-2, INPUT, NONE);
> >> + PIN_SLP(gpj0-3, INPUT, NONE);
> >> + PIN_SLP(gpj0-4, INPUT, NONE);
> >> + PIN_SLP(gpj0-5, INPUT, DOWN);
> >> + PIN_SLP(gpj0-6, OUT0, NONE);
> >> + PIN_SLP(gpj0-7, INPUT, NONE);
> >> +
> >> + PIN_SLP(gpj1-0, OUT1, NONE);
> >> + PIN_SLP(gpj1-1, OUT0, NONE);
> >> + PIN_SLP(gpj1-2, INPUT, DOWN);
> >> + PIN_SLP(gpj1-3, PREV, NONE);
> >> + PIN_SLP(gpj1-4, PREV, NONE);
> >> + PIN_SLP(gpj1-5, OUT0, NONE);
> >> +
> >> + PIN_SLP(gpj2-0, INPUT, DOWN);
> >> + PIN_SLP(gpj2-1, INPUT, DOWN);
> >> + PIN_SLP(gpj2-2, OUT0, NONE);
> >> + PIN_SLP(gpj2-3, INPUT, DOWN);
> >> + PIN_SLP(gpj2-4, INPUT, DOWN);
> >> + PIN_SLP(gpj2-5, PREV, NONE);
> >> + PIN_SLP(gpj2-6, PREV, NONE);
> >> + PIN_SLP(gpj2-7, INPUT, DOWN);
> >> +
> >> + PIN_SLP(gpj3-0, INPUT, NONE);
> >> + PIN_SLP(gpj3-1, INPUT, NONE);
> >> + PIN_SLP(gpj3-2, OUT0, NONE);
> >> + PIN_SLP(gpj3-3, INPUT, DOWN);
> >> + PIN_SLP(gpj3-4, INPUT, NONE);
> >> + PIN_SLP(gpj3-5, INPUT, NONE);
> >> + PIN_SLP(gpj3-6, INPUT, NONE);
> >> + PIN_SLP(gpj3-7, INPUT, NONE);
> >> +
> >> + PIN_SLP(gpj4-0, INPUT, NONE);
> >> + PIN_SLP(gpj4-1, INPUT, DOWN);
> >> + PIN_SLP(gpj4-2, PREV, NONE);
> >> + PIN_SLP(gpj4-3, INPUT, NONE);
> >> + PIN_SLP(gpj4-4, INPUT, DOWN);
> >> +
> >> + PIN_SLP(mp01-0, OUT1, NONE);
> >> + PIN_SLP(mp01-1, OUT0, NONE);
> >> + PIN_SLP(mp01-2, INPUT, DOWN);
> >> + PIN_SLP(mp01-3, INPUT, DOWN);
> >> + PIN_SLP(mp01-4, OUT1, NONE);
> >> + PIN_SLP(mp01-5, INPUT, DOWN);
> >> + PIN_SLP(mp01-6, INPUT, DOWN);
> >> + PIN_SLP(mp01-7, INPUT, DOWN);
> >> +
> >> + PIN_SLP(mp02-0, INPUT, DOWN);
> >> + PIN_SLP(mp02-1, INPUT, DOWN);
> >> + PIN_SLP(mp02-2, INPUT, NONE);
> >> + PIN_SLP(mp02-3, INPUT, DOWN);
> >> +
> >> + PIN_SLP(mp03-0, INPUT, DOWN);
> >> + PIN_SLP(mp03-1, INPUT, DOWN);
> >> + PIN_SLP(mp03-2, OUT1, NONE);
> >> + PIN_SLP(mp03-3, OUT0, NONE);
> >> + PIN_SLP(mp03-4, INPUT, NONE);
> >> + PIN_SLP(mp03-5, OUT0, NONE);
> >> + PIN_SLP(mp03-6, INPUT, DOWN);
> >> + PIN_SLP(mp03-7, INPUT, DOWN);
> >> +
> >> + PIN_SLP(mp04-0, INPUT, DOWN);
> >> + PIN_SLP(mp04-1, OUT0, NONE);
> >> + PIN_SLP(mp04-2, INPUT, DOWN);
> >> + PIN_SLP(mp04-3, OUT0, NONE);
> >> + PIN_SLP(mp04-4, INPUT, DOWN);
> >> + PIN_SLP(mp04-5, INPUT, DOWN);
> >> + PIN_SLP(mp04-6, OUT0, NONE);
> >> + PIN_SLP(mp04-7, INPUT, DOWN);
> >> +
> >> + PIN_SLP(mp05-0, INPUT, NONE);
> >> + PIN_SLP(mp05-1, INPUT, NONE);
> >> + PIN_SLP(mp05-2, INPUT, NONE);
> >> + PIN_SLP(mp05-3, INPUT, NONE);
> >> + PIN_SLP(mp05-4, INPUT, DOWN);
> >> + PIN_SLP(mp05-5, OUT0, NONE);
> >> + PIN_SLP(mp05-6, INPUT, DOWN);
> >> + PIN_SLP(mp05-7, PREV, NONE);
> >> +
> >> + PIN_SLP(mp06-0, INPUT, DOWN);
> >> + PIN_SLP(mp06-1, INPUT, DOWN);
> >> + PIN_SLP(mp06-2, INPUT, DOWN);
> >> + PIN_SLP(mp06-3, INPUT, DOWN);
> >> + PIN_SLP(mp06-4, INPUT, DOWN);
> >> + PIN_SLP(mp06-5, INPUT, DOWN);
> >> + PIN_SLP(mp06-6, INPUT, DOWN);
> >> + PIN_SLP(mp06-7, INPUT, DOWN);
> >> +
> >> + PIN_SLP(mp07-0, INPUT, DOWN);
> >> + PIN_SLP(mp07-1, INPUT, DOWN);
> >> + PIN_SLP(mp07-2, INPUT, DOWN);
> >> + PIN_SLP(mp07-3, INPUT, DOWN);
> >> + PIN_SLP(mp07-4, INPUT, DOWN);
> >> + PIN_SLP(mp07-5, INPUT, DOWN);
> >> + PIN_SLP(mp07-6, INPUT, DOWN);
> >> + PIN_SLP(mp07-7, INPUT, DOWN);
> >> + };
> >
> > What about gphX?
>
> The gphX pins are in the alive area and don't have power down configs, they retain their
> state over suspend. Therefore the samsung,pin-con-pdn and samsung,pin-pud-pdn properties
> have no effect (they're analogous to the gpxX pins in later Samsung SoCs).

Ah, good, thanks.

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2020-05-01 15:10    [W:0.077 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site