lkml.org 
[lkml]   [2020]   [Apr]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 1/2] dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings
From
Date
Hi Rob,

On 4/4/2020 10:47 PM, Rob Herring wrote:
> On Thu, Mar 26, 2020 at 12:36:07PM +0530, Sandeep Maheswaram wrote:
>> Convert USB DWC3 bindings to DT schema format using json-schema.
>>
>> Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
>> ---
>> .../devicetree/bindings/usb/qcom,dwc3.txt | 104 --------------
>> .../devicetree/bindings/usb/qcom,dwc3.yaml | 158 +++++++++++++++++++++
>> 2 files changed, 158 insertions(+), 104 deletions(-)
>> delete mode 100644 Documentation/devicetree/bindings/usb/qcom,dwc3.txt
>> create mode 100644 Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
>
>> diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
>> new file mode 100644
>> index 0000000..0f69475
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
>> @@ -0,0 +1,158 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm SuperSpeed DWC3 USB SoC controller
>> +
>> +maintainers:
>> + - Manu Gautam <mgautam@codeaurora.org>
>> +
>> +properties:
>> + compatible:
>> + items:
>> + - enum:
>> + - qcom,msm8996-dwc3
>> + - qcom,msm8998-dwc3
>> + - qcom,sdm845-dwc3
>> + - const: qcom,dwc3
>> +
>> + reg:
>> + description: Offset and length of register set for QSCRATCH wrapper
>> + maxItems: 1
>> +
>> + "#address-cells":
>> + enum: [ 1, 2 ]
>> +
>> + "#size-cells":
>> + enum: [ 1, 2 ]
>> +
>> + power-domains:
>> + description: specifies a phandle to PM domain provider node
>> + maxItems: 1
>> +
>> + clocks:
>> + description:
>> + A list of phandle and clock-specifier pairs for the clocks
>> + listed in clock-names.
>> + items:
>> + - description: System Config NOC clock.
>> + - description: Master/Core clock, has to be >= 125 MHz
>> + for SS operation and >= 60MHz for HS operation.
>> + - description: System bus AXI clock.
>> + - description: Mock utmi clock needed for ITP/SOF generation
>> + in host mode. Its frequency should be 19.2MHz.
>> + - description: Sleep clock, used for wakeup when
>> + USB3 core goes into low power mode (U3).
>> +
>> + clock-names:
>> + items:
>> + - const: cfg_noc
>> + - const: core
>> + - const: iface
>> + - const: mock_utmi
>> + - const: sleep
>> +
>> + assigned-clocks:
>> + items:
>> + - description: Phandle and clock specifier of MOCK_UTMI_CLK.
>> + - description: Phandle and clock specifoer of MASTER_CLK.
>> +
>> + assigned-clock-rates:
>> + maxItems: 2
> Need to drop this as it is redundant. Soon this will generate an error.
Will do in next version.
>> + items:
>> + - description: Must be 19.2MHz (19200000).
> Sounds like a constraint:
>
> - const: 19200000
>
>> + - description: Must be >= 60 MHz in HS mode, >= 125 MHz in SS mode.
> - minimum: 60000000
> maximum: ?

Tried  as below but facing errors

assigned-clock-rates:
    items:
      - const: 19200000
      - minimum: 60000000
        maximum: 150000000

Errors

linux-next/Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml:
usb@a6f8800: assigned-clock-rates: Additional items are not allowed
([150000000] was unexpected)
linux-next/Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml:
usb@a6f8800: assigned-clock-rates:0: [19200000] is too short
linux-next/Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml:
usb@a6f8800: assigned-clock-rates: [[19200000], [150000000]] is too long

>> +
>> + resets:
>> + maxItems: 1
>> +
>> + interrupts:
>> + items:
>> + - description: The interrupt that is asserted
>> + when a wakeup event is received on USB2 bus.
>> + - description: The interrupt that is asserted
>> + when a wakeup event is received on USB3 bus.
>> + - description: Wakeup event on DM line.
>> + - description: Wakeup event on DP line.
>> +
>> + interrupt-names:
>> + items:
>> + - const: hs_phy_irq
>> + - const: ss_phy_irq
>> + - const: dm_hs_phy_irq
>> + - const: dp_hs_phy_irq
>> +
>> + qcom,select-utmi-as-pipe-clk:
>> + description:
>> + If present, disable USB3 pipe_clk requirement.
>> + Used when dwc3 operates without SSPHY and only
>> + HS/FS/LS modes are supported.
>> + type: boolean
>> +
>> +# Required child node:
>> +
>> +patternProperties:
>> + "^dwc3@[0-9a-f]+$":
>> + type: object
>> + description:
>> + A child node must exist to represent the core DWC3 IP block
>> + The content of the node is defined in dwc3.txt.
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - "#address-cells"
>> + - "#size-cells"
>> + - power-domains
>> + - clocks
>> + - clock-names
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
>> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>> + #include <dt-bindings/interrupt-controller/irq.h>
>> + usb@a6f8800 {
>> + compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
>> + reg = <0 0x0a6f8800 0 0x400>;
>> +
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
>> + <&gcc GCC_USB30_PRIM_MASTER_CLK>,
>> + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
>> + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
>> + <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
>> + clock-names = "cfg_noc", "core", "iface", "mock_utmi",
>> + "sleep";
>> +
>> + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
>> + <&gcc GCC_USB30_PRIM_MASTER_CLK>;
>> + assigned-clock-rates = <19200000>, <150000000>;
>> +
>> + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "hs_phy_irq", "ss_phy_irq",
>> + "dm_hs_phy_irq", "dp_hs_phy_irq";
>> +
>> + power-domains = <&gcc USB30_PRIM_GDSC>;
>> +
>> + resets = <&gcc GCC_USB30_PRIM_BCR>;
>> +
>> + dwc3@a600000 {
>> + compatible = "snps,dwc3";
>> + reg = <0 0x0a600000 0 0xcd00>;
> You need 'ranges' in the parent for this address to be translatable.
Will add in next version.
>
>> + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
>> + iommus = <&apps_smmu 0x740 0>;
>> + snps,dis_u2_susphy_quirk;
>> + snps,dis_enblslpm_quirk;
>> + phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
>> + phy-names = "usb2-phy", "usb3-phy";
>> + };
>> + };
>> --
>> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
>> of Code Aurora Forum, hosted by The Linux Foundation
>>
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

\
 
 \ /
  Last update: 2020-04-06 18:40    [W:0.138 / U:0.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site