lkml.org 
[lkml]   [2020]   [Apr]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 4/4] drm/mediatek: config mipitx impedance with calibration data
From
Date

On Sat, 2020-04-04 at 22:26 +0800, Chun-Kuang Hu wrote:
> Hi, Jitao:
>
> Jitao Shi <jitao.shi@mediatek.com> 於 2020年3月31日 週二 下午4:28寫道:
> >
> > Read calibration data from nvmem, and config mipitx impedance with
> > calibration data to make sure their impedance are 100ohm.
> >
> > Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> > ---
> > drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c | 57 +++++++++++++++++++
> > 1 file changed, 57 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
> > index e4cc967750cb..0f87cd3d1d7d 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
> > @@ -5,6 +5,8 @@
> > */
> >
> > #include "mtk_mipi_tx.h"
> > +#include <linux/nvmem-consumer.h>
> > +#include <linux/slab.h>
> >
> > #define MIPITX_LANE_CON 0x000c
> > #define RG_DSI_CPHY_T1DRV_EN BIT(0)
> > @@ -28,6 +30,7 @@
> > #define MIPITX_PLL_CON4 0x003c
> > #define RG_DSI_PLL_IBIAS (3 << 10)
> >
> > +#define MIPITX_D2P_RTCODE 0x0100
> > #define MIPITX_D2_SW_CTL_EN 0x0144
> > #define MIPITX_D0_SW_CTL_EN 0x0244
> > #define MIPITX_CK_CKMODE_EN 0x0328
> > @@ -108,6 +111,58 @@ static const struct clk_ops mtk_mipi_tx_pll_ops = {
> > .recalc_rate = mtk_mipi_tx_pll_recalc_rate,
> > };
> >
> > +static void mtk_mipi_tx_config_calibration_data(struct mtk_mipi_tx *mipi_tx)
> > +{
> > + u32 *buf;
> > + u32 rt_code[5];
> > + int i, j;
> > + struct nvmem_cell *cell;
> > + struct device *dev = mipi_tx->dev;
> > + size_t len;
> > +
> > + cell = nvmem_cell_get(dev, "calibration-data");
> > + if (IS_ERR(cell)) {
> > + dev_info(dev, "nvmem_cell_get fail\n");
> > + return;
> > + }
> > +
> > + buf = (u32 *)nvmem_cell_read(cell, &len);
> > +
> > + nvmem_cell_put(cell);
> > +
> > + if (IS_ERR(buf)) {
> > + dev_info(dev, "can't get data\n");
> > + return;
> > + }
> > +
> > + if (len < 3 * sizeof(u32)) {
> > + dev_info(dev, "invalid calibration data\n");
> > + kfree(buf);
> > + return;
> > + }
> > +
> > + rt_code[0] = ((buf[0] >> 6 & 0x1f) << 5) | (buf[0] >> 11 & 0x1f);
> > + rt_code[1] = ((buf[1] >> 27 & 0x1f) << 5) | (buf[0] >> 1 & 0x1f);
> > + rt_code[2] = ((buf[1] >> 17 & 0x1f) << 5) | (buf[1] >> 22 & 0x1f);
> > + rt_code[3] = ((buf[1] >> 7 & 0x1f) << 5) | (buf[1] >> 12 & 0x1f);
> > + rt_code[4] = ((buf[2] >> 27 & 0x1f) << 5) | (buf[1] >> 2 & 0x1f);
>
> Why not just save rt_code in nvmem and you don't need to translate here?
> If you need to do so, please add description for this.
>
> Regards,
> Chun-Kuang.
>

Hi Chun-Kuang,

The calibration data is flashed in rom when the IC FT test
And the data struct can't be stored again

Best Regards
JItao
>
> > +
> > + for (i = 0; i < 5; i++) {
> > + if ((rt_code[i] & 0x1f) == 0)
> > + rt_code[i] |= 0x10;
> > +
> > + if ((rt_code[i] >> 5 & 0x1f) == 0)
> > + rt_code[i] |= 0x10 << 5;
> > +
> > + for (j = 0; j < 10; j++)
> > + mtk_mipi_tx_update_bits(mipi_tx,
> > + MIPITX_D2P_RTCODE * (i + 1) + j * 4,
> > + 1, rt_code[i] >> j & 1);
> > + }
> > +
> > + kfree(buf);
> > +}
> > +
> > static void mtk_mipi_tx_power_on_signal(struct phy *phy)
> > {
> > struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
> > @@ -130,6 +185,8 @@ static void mtk_mipi_tx_power_on_signal(struct phy *phy)
> > RG_DSI_HSTX_LDO_REF_SEL,
> > (mipi_tx->mipitx_drive - 3000) / 200 << 6);
> >
> > + mtk_mipi_tx_config_calibration_data(mipi_tx);
> > +
> > mtk_mipi_tx_set_bits(mipi_tx, MIPITX_CK_CKMODE_EN, DSI_CK_CKMODE_EN);
> > }
> >
> > --
> > 2.21.0
> > _______________________________________________
> > dri-devel mailing list
> > dri-devel@lists.freedesktop.org
> > https://lists.freedesktop.org/mailman/listinfo/dri-devel


\
 
 \ /
  Last update: 2020-04-05 15:39    [W:0.049 / U:0.728 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site