lkml.org 
[lkml]   [2020]   [Apr]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH net-next v3] net: phy: micrel: add phy-mode support for the KSZ9031 PHY
Hi Oleksij,

On Wed, Apr 22, 2020 at 9:24 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid.
>
> This PHY has an internal RX delay of 1.2ns and no delay for TX.
>
> The pad skew registers allow to set the total TX delay to max 1.38ns and
> the total RX delay to max of 2.58ns (configurable 1.38ns + build in
> 1.2ns) and a minimal delay of 0ns.
>
> According to the RGMII v1.3 specification the delay provided by PCB traces
> should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this
> delay by MAC or PHY. So, we configure this PHY to the best values we can
> get by this HW: TX delay to 1.38ns (max supported value) and RX delay to
> 1.80ns (best calculated delay)
>
> The phy-modes can still be fine tuned/overwritten by *-skew-ps
> device tree properties described in:
> Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

This is now commit bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY") in net-next/master.

> --- a/drivers/net/phy/micrel.c
> +++ b/drivers/net/phy/micrel.c

> @@ -597,21 +703,33 @@ static int ksz9031_config_init(struct phy_device *phydev)
> } while (!of_node && dev_walker);
>
> if (of_node) {
> + bool update = false;
> +
> + if (phy_interface_is_rgmii(phydev)) {
> + result = ksz9031_config_rgmii_delay(phydev);
> + if (result < 0)
> + return result;
> + }
> +
> ksz9031_of_load_skew_values(phydev, of_node,
> MII_KSZ9031RN_CLK_PAD_SKEW, 5,
> - clk_skews, 2);
> + clk_skews, 2, &update);
>
> ksz9031_of_load_skew_values(phydev, of_node,
> MII_KSZ9031RN_CONTROL_PAD_SKEW, 4,
> - control_skews, 2);
> + control_skews, 2, &update);
>
> ksz9031_of_load_skew_values(phydev, of_node,
> MII_KSZ9031RN_RX_DATA_PAD_SKEW, 4,
> - rx_data_skews, 4);
> + rx_data_skews, 4, &update);
>
> ksz9031_of_load_skew_values(phydev, of_node,
> MII_KSZ9031RN_TX_DATA_PAD_SKEW, 4,
> - tx_data_skews, 4);
> + tx_data_skews, 4, &update);
> +
> + if (update && phydev->interface != PHY_INTERFACE_MODE_RGMII)
> + phydev_warn(phydev,
> + "*-skew-ps values should be used only with phy-mode = \"rgmii\"\n");

This triggers on Renesas Salvator-X(S):

Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00:
*-skew-ps values should be used only with phy-mode = "rgmii"

which uses:

phy-mode = "rgmii-txid";

and:

rxc-skew-ps = <1500>;

If I understand Documentation/devicetree/bindings/net/ethernet-controller.yaml
correctly:

# RX and TX delays are added by the MAC when required
- rgmii

i.e. any *-skew-ps can be specified.

# RGMII with internal RX and TX delays provided by the PHY,
# the MAC should not add the RX or TX delays in this case
- rgmii-id

i.e. *-skew-ps must not be specified.

# RGMII with internal RX delay provided by the PHY, the MAC
# should not add an RX delay in this case
- rgmii-rxid

i.e. it's still OK to specify tx*-skew-ps values here...

# RGMII with internal TX delay provided by the PHY, the MAC
# should not add an TX delay in this case
- rgmii-txid

... and rx*-skew-ps values here?
Is my understanding correct, and should the check be updated to take into
account rxid and txid?

BTW, the example in Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
still specifies *-skew-ps values with phy-mode = "rgmii-id", so I think
that should be updated, too.

Thanks!

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

\
 
 \ /
  Last update: 2020-04-28 17:28    [W:0.183 / U:0.892 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site