lkml.org 
[lkml]   [2020]   [Apr]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 1/3] remoteproc: imx_rproc: set pc on start
On Fri, 17 Apr 2020 at 06:12, Nikita Shubin <nikita.shubin@maquefel.me> wrote:
>
> On Tue, 14 Apr 2020 10:45:19 -0600
> Mathieu Poirier <mathieu.poirier@linaro.org> wrote:
>
> > Hi Nikita,
> >
> > On Mon, Apr 06, 2020 at 02:33:08PM +0300, nikita.shubin@maquefel.me
> > wrote:
> > > In case elf file interrupt vector is not supposed to be at OCRAM_S,
> > > it is needed to write elf entry point to OCRAM_S + 0x4, to boot M4
> > > firmware.
> > >
> > > Otherwise firmware located anywhere besides OCRAM_S won't boot.
> > >
> > > The firmware must set stack poiner as first instruction:
> > >
> > > Reset_Handler:
> > > ldr sp, = __stack /* set stack pointer */
> > >
> > > Signed-off-by: Nikita Shubin <NShubin@topcon.com>
> >
> > The address in the SoB has to match what is found in the "From:"
> > field of the email header. Checkpatch is complaining about that,
> > something I would have expected to be fixed before sending this set
> > out.
> >
> > > ---
> > > drivers/remoteproc/imx_rproc.c | 16 +++++++++++++++-
> > > 1 file changed, 15 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/remoteproc/imx_rproc.c
> > > b/drivers/remoteproc/imx_rproc.c index 3e72b6f38d4b..bebc58d0f711
> > > 100644 --- a/drivers/remoteproc/imx_rproc.c
> > > +++ b/drivers/remoteproc/imx_rproc.c
> > > @@ -45,6 +45,8 @@
> > >
> > > #define IMX7D_RPROC_MEM_MAX 8
> > >
> > > +#define IMX_BOOT_PC 0x4
> > > +
> > > /**
> > > * struct imx_rproc_mem - slim internal memory structure
> > > * @cpu_addr: MPU virtual address of the memory region
> > > @@ -85,6 +87,7 @@ struct imx_rproc {
> > > const struct imx_rproc_dcfg *dcfg;
> > > struct imx_rproc_mem
> > > mem[IMX7D_RPROC_MEM_MAX]; struct clk *clk;
> > > + void __iomem *bootreg;
> > > };
> > >
> > > static const struct imx_rproc_att imx_rproc_att_imx7d[] = {
> > > @@ -162,11 +165,16 @@ static int imx_rproc_start(struct rproc
> > > *rproc) struct device *dev = priv->dev;
> > > int ret;
> > >
> > > + /* write entry point to program counter */
> > > + writel(rproc->bootaddr, priv->bootreg);
> >
> > What happens on all the other IMX systems where this fix is not
> > needed? Will they continue to work properly?
>
> Mathieu you are totally correct imx6/imx7 use different addresses they
> boot.
>
> For imx7:
> | On i.MX 7Dual/7Solo, the boot vector for the Cortex-M4 core is located
> | at the start of the OCRAM_S (On Chip RAM - Secure) whose address is
> | 0x0018_0000 from Cortex-A7.
>
> For imx6:
> | The Boot vector for the Cortex-M4 core is located at the start of the
> | TCM_L whose address is 0x007F_8000 from the Cortex-A9. This is a
> | different location than on the i.MX 7Dual/7Solo
>
> But on imx7 0x0 is translated to 0x0018_0000 by imx_rproc_da_to_va, and
> on imx7 0x0 is translated to 0x007F_8000, using imx_rproc_att_imx7d and
> imx_rproc_att_imx6sx respectively.

My point here is that before your patch, this driver was running on
IMX platforms. How does your work impact existing platforms that are
booting properly?

>
> I have no information about IMX8 (i have found none available
> publicity), but should be the same as Cortex-M boots from 0x0.
>
> >
> > > +
> > > ret = regmap_update_bits(priv->regmap, dcfg->src_reg,
> > > dcfg->src_mask, dcfg->src_start);
> > > if (ret)
> > > dev_err(dev, "Failed to enable M4!\n");
> > >
> > > + dev_info(&rproc->dev, "Started from 0x%x\n",
> > > rproc->bootaddr); +
> > > return ret;
> > > }
> > >
> > > @@ -182,6 +190,9 @@ static int imx_rproc_stop(struct rproc *rproc)
> > > if (ret)
> > > dev_err(dev, "Failed to stop M4!\n");
> > >
> > > + /* clear entry points */
> > > + writel(0, priv->bootreg);
> > > +
> > > return ret;
> > > }
> > >
> > > @@ -243,7 +254,8 @@ static void *imx_rproc_da_to_va(struct rproc
> > > *rproc, u64 da, int len) static const struct rproc_ops
> > > imx_rproc_ops = { .start = imx_rproc_start,
> > > .stop = imx_rproc_stop,
> > > - .da_to_va = imx_rproc_da_to_va,
> > > + .da_to_va = imx_rproc_da_to_va,
> > > + .get_boot_addr = rproc_elf_get_boot_addr,
> >
> > How is this useful? Sure it will set rproc->bootaddr in
> > rproc_fw_boot() but what good does that do when it is invariably set
> > again in imx_rproc_start() ?
> >
> > > };
> > >
> > > static int imx_rproc_addr_init(struct imx_rproc *priv,
> > > @@ -360,6 +372,8 @@ static int imx_rproc_probe(struct
> > > platform_device *pdev) goto err_put_rproc;
> > > }
> > >
> > > + priv->bootreg = imx_rproc_da_to_va(rproc, IMX_BOOT_PC,
> > > sizeof(u32)); +
> > > /*
> > > * clk for M4 block including memory. Should be
> > > * enabled before .start for FW transfer.
> > > --
> > > 2.25.1
> > >
>

\
 
 \ /
  Last update: 2020-04-17 17:39    [W:0.128 / U:0.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site