lkml.org 
[lkml]   [2020]   [Mar]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 26/42] docs: scsi: convert qlogicfas.txt to ReST
    Date
    Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
    ---
    Documentation/scsi/index.rst | 1 +
    .../scsi/{qlogicfas.txt => qlogicfas.rst} | 17 +++++++++++++----
    drivers/scsi/Kconfig | 2 +-
    3 files changed, 15 insertions(+), 5 deletions(-)
    rename Documentation/scsi/{qlogicfas.txt => qlogicfas.rst} (92%)

    diff --git a/Documentation/scsi/index.rst b/Documentation/scsi/index.rst
    index 17327f67af68..29e211ee9145 100644
    --- a/Documentation/scsi/index.rst
    +++ b/Documentation/scsi/index.rst
    @@ -30,5 +30,6 @@ Linux SCSI Subsystem
    ncr53c8xx
    NinjaSCSI
    ppa
    + qlogicfas

    scsi_transport_srp/figures
    diff --git a/Documentation/scsi/qlogicfas.txt b/Documentation/scsi/qlogicfas.rst
    similarity index 92%
    rename from Documentation/scsi/qlogicfas.txt
    rename to Documentation/scsi/qlogicfas.rst
    index c211d827fef2..b17f1b3676c3 100644
    --- a/Documentation/scsi/qlogicfas.txt
    +++ b/Documentation/scsi/qlogicfas.rst
    @@ -1,3 +1,8 @@
    +.. SPDX-License-Identifier: GPL-2.0
    +
    +=================================
    +Qlogic FASXXX Family Driver Notes
    +=================================

    This driver supports the Qlogic FASXXX family of chips. This driver
    only works with the ISA, VLB, and PCMCIA versions of the Qlogic
    @@ -16,7 +21,8 @@ is provided by the qla1280 driver.
    Nor does it support the PCI-Basic, which is supported by the
    'am53c974' driver.

    -PCMCIA SUPPORT
    +PCMCIA Support
    +==============

    This currently only works if the card is enabled first from DOS. This
    means you will have to load your socket and card services, and
    @@ -31,7 +37,8 @@ it from configuring the card.
    I am working with the PCMCIA group to make it more flexible, but that
    may take a while.

    -ALL CARDS
    +All Cards
    +=========

    The top of the qlogic.c file has a number of defines that controls
    configuration. As shipped, it provides a balance between speed and
    @@ -46,7 +53,8 @@ command or something. It comes up faster if this is set to zero, and
    if you have reliable hardware and connections it may be more useful to
    not reset things.

    -SOME TROUBLESHOOTING TIPS
    +Some Troubleshooting Tips
    +=========================

    Make sure it works properly under DOS. You should also do an initial FDISK
    on a new drive if you want partitions.
    @@ -54,7 +62,8 @@ on a new drive if you want partitions.
    Don't enable all the speedups first. If anything is wrong, they will make
    any problem worse.

    -IMPORTANT
    +Important
    +=========

    The best way to test if your cables, termination, etc. are good is to
    copy a very big file (e.g. a doublespace container file, or a very
    diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
    index 82462d6a4ce5..d34c682e94cf 100644
    --- a/drivers/scsi/Kconfig
    +++ b/drivers/scsi/Kconfig
    @@ -1117,7 +1117,7 @@ config SCSI_QLOGIC_FAS
    SCSI support"), below.

    Information about this driver is contained in
    - <file:Documentation/scsi/qlogicfas.txt>. You should also read the
    + <file:Documentation/scsi/qlogicfas.rst>. You should also read the
    SCSI-HOWTO, available from
    <http://www.tldp.org/docs.html#howto>.

    --
    2.21.1
    \
     
     \ /
      Last update: 2020-03-02 09:18    [W:2.524 / U:0.008 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site