lkml.org 
[lkml]   [2020]   [Mar]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] [RFC] rcar-vin: rcar-csi2: Correct the selection of hsfreqrange
Hi Suresh,

Thanks for your work.

On 2020-03-17 16:08:25 +0900, Suresh Udipi wrote:
> hsfreqrange should be chosen based on the calculated mbps which
> is closer to the default bit rate and within the range as per
> table[1]. But current calculation always selects first value which
> is greater than or equal to the calculated mbps which may lead
> to chosing a wrong range in some cases.
>
> For example for 360 mbps for H3/M3N
> Existing logic selects
> Calculated value 360Mbps : Default 400Mbps Range [368.125 -433.125 mbps]
>
> This hsfreqrange is out of range.
>
> The logic is changed to get the default value which is closest to the
> calculated value [1]
>
> Calculated value 360Mbps : Default 350Mbps Range [320.625 -380.625 mpbs]
>
> [1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]
>
> There is one exectpion value 227Mbps, which may cause out of
> range.

Then something else is needed I think :-)

I liked v1 of this RFC more, where you added a u16 min and max to struct
rcsi2_mbps_reg. I think that is the right solution.

What I tried to express in my review of v1 was

- You should remove the mbps member from struct rcsi2_mbps_reg.
- Update the walk of the array in rcsi2_set_phypll() so that it finds
the first entry where the calculated target value is between min and
max and use the reg setting for that entry.

Would that solution make sens too you? Sorry if I expressed myself a but
muddy in v1 about this.

>
> Fixes: 769afd212b16 ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
>
> Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
> Signed-off-by: Kazuyoshi Akiyama <akiyama@nds-osk.co.jp>
> ---
> Changes in v2:
> - Added the boundary check for the maximum bit rate.
>
> - Simplified the logic by remmoving range check
> as only the closest default value covers most
> of the use cases.
>
> - Aligning the commit message based on the above change
>
> drivers/media/platform/rcar-vin/rcar-csi2.c | 18 +++++++++++++-----
> 1 file changed, 13 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/media/platform/rcar-vin/rcar-csi2.c b/drivers/media/platform/rcar-vin/rcar-csi2.c
> index faa9fb2..6573625 100644
> --- a/drivers/media/platform/rcar-vin/rcar-csi2.c
> +++ b/drivers/media/platform/rcar-vin/rcar-csi2.c
> @@ -199,6 +199,7 @@ static const struct rcsi2_mbps_reg phtw_mbps_v3m_e3[] = {
> /* PHY Frequency Control */
> #define PHYPLL_REG 0x68
> #define PHYPLL_HSFREQRANGE(n) ((n) << 16)
> +#define PHYPLL_HSFREQRANGE_MAX 1500
>
> static const struct rcsi2_mbps_reg hsfreqrange_h3_v3h_m3n[] = {
> { .mbps = 80, .reg = 0x00 },
> @@ -431,16 +432,23 @@ static int rcsi2_wait_phy_start(struct rcar_csi2 *priv)
> static int rcsi2_set_phypll(struct rcar_csi2 *priv, unsigned int mbps)
> {
> const struct rcsi2_mbps_reg *hsfreq;
> + const struct rcsi2_mbps_reg *hsfreq_prev = NULL;
>
> - for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++)
> - if (hsfreq->mbps >= mbps)
> - break;
> -
> - if (!hsfreq->mbps) {
> + if (mbps > PHYPLL_HSFREQRANGE_MAX) {
> dev_err(priv->dev, "Unsupported PHY speed (%u Mbps)", mbps);
> return -ERANGE;
> }
>
> + for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++) {
> + if (hsfreq->mbps >= mbps)
> + break;
> + hsfreq_prev = hsfreq;
> + }
> +
> + if (hsfreq_prev &&
> + ((mbps - hsfreq_prev->mbps) <= (hsfreq->mbps - mbps)))
> + hsfreq = hsfreq_prev;
> +
> rcsi2_write(priv, PHYPLL_REG, PHYPLL_HSFREQRANGE(hsfreq->reg));
>
> return 0;
> --
> 2.7.4
>

--
Regards,
Niklas Söderlund

\
 
 \ /
  Last update: 2020-03-17 11:39    [W:0.233 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site