lkml.org 
[lkml]   [2020]   [Mar]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] media: i2c: ov5695: Fix power on and off sequences
Hi Tomasz,

On Wed, Mar 11, 2020 at 07:39:15PM +0900, Tomasz Figa wrote:
> Hi Sakari,
>
> On Sat, Dec 21, 2019 at 12:19 AM Sakari Ailus
> <sakari.ailus@linux.intel.com> wrote:
> >
> > Hi Tomasz,
> >
> > On Fri, Dec 20, 2019 at 10:08:00PM +0900, Tomasz Figa wrote:
> > > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > >
> > > From the measured hardware signal, OV5695 reset pin goes high for a
> > > short period of time during boot-up. From the sensor specification, the
> > > reset pin is active low and the DT binding defines the pin as active
> > > low, which means that the values set by the driver are inverted and thus
> > > the value requested in probe ends up high.
> > >
> > > Fix it by changing probe to request the reset GPIO initialized to high,
> > > which makes the initial state of the physical signal low.
> > >
> > > In addition, DOVDD rising must occur before DVDD rising from spec., but
> > > regulator_bulk_enable() API enables all the regulators asynchronously.
> > > Use an explicit loops of regulator_enable() instead.
> > >
> > > For power off sequence, it is required that DVDD falls first. Given the
> > > bulk API does not give any guarantee about the order of regulators,
> > > change the driver to use regulator_disable() instead.
> > >
> > > The sensor also requires a delay between reset high and first I2C
> > > transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
> > > recommended by the vendor. Fix this as well.
> > >
> > > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > > Signed-off-by: Tomasz Figa <tfiga@chromium.org>
> > > ---
> > > drivers/media/i2c/ov5695.c | 41 +++++++++++++++++++++-----------------
> > > 1 file changed, 23 insertions(+), 18 deletions(-)
> > >
> > > diff --git a/drivers/media/i2c/ov5695.c b/drivers/media/i2c/ov5695.c
> > > index d6cd15bb699ac..8d0cc3893fcfc 100644
> > > --- a/drivers/media/i2c/ov5695.c
> > > +++ b/drivers/media/i2c/ov5695.c
> > > @@ -971,16 +971,9 @@ static int ov5695_s_stream(struct v4l2_subdev *sd, int on)
> > > return ret;
> > > }
> > >
> > > -/* Calculate the delay in us by clock rate and clock cycles */
> > > -static inline u32 ov5695_cal_delay(u32 cycles)
> > > -{
> > > - return DIV_ROUND_UP(cycles, OV5695_XVCLK_FREQ / 1000 / 1000);
> > > -}
> > > -
> > > static int __ov5695_power_on(struct ov5695 *ov5695)
> > > {
> > > - int ret;
> > > - u32 delay_us;
> > > + int i, ret;
> > > struct device *dev = &ov5695->client->dev;
> > >
> > > ret = clk_prepare_enable(ov5695->xvclk);
> > > @@ -991,21 +984,24 @@ static int __ov5695_power_on(struct ov5695 *ov5695)
> > >
> > > gpiod_set_value_cansleep(ov5695->reset_gpio, 1);
> > >
> > > - ret = regulator_bulk_enable(OV5695_NUM_SUPPLIES, ov5695->supplies);
> > > - if (ret < 0) {
> > > - dev_err(dev, "Failed to enable regulators\n");
> > > - goto disable_clk;
> > > + for (i = 0; i < OV5695_NUM_SUPPLIES; i++) {
> > > + ret = regulator_enable(ov5695->supplies[i].consumer);
> >
> > The regulator voltage takes some time before it settles. If the hardware
> > requires a particular order, then presumably there should be a small delay
> > to ensure that. 1 ms should be plenty.
>
> The regulator API guarantees that when regulator_enable() returns, the
> voltage is stable. Regulator ramp up delays can be also configured via
> DT to take care for per-platform variability.

Ack. In practice not many drivers do that still. But that should probably
be seen as a driver bug indeed.

--
Regards,

Sakari Ailus

\
 
 \ /
  Last update: 2020-03-11 11:46    [W:0.051 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site