Messages in this thread | | | Date | Thu, 6 Feb 2020 10:43:58 -0700 | From | Jerry Snitselaar <> | Subject | Re: warning from domain_get_iommu |
| |
On Tue Feb 04 20, Jerry Snitselaar wrote: >I'm working on getting a system to reproduce this, and verify it also occurs >with 5.5, but I have a report of a case where the kdump kernel gives >warnings like the following on a hp dl360 gen9: > >[ 2.830589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >[ 2.832615] ehci-pci: EHCI PCI platform driver >[ 2.834190] ehci-pci 0000:00:1a.0: EHCI Host Controller >[ 2.835974] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1 >[ 2.838276] ehci-pci 0000:00:1a.0: debug port 2 >[ 2.839700] WARNING: CPU: 0 PID: 1 at drivers/iommu/intel-iommu.c:598 domain_get_iommu+0x55/0x60 >[ 2.840671] Modules linked in: >[ 2.840671] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.0-170.el8.kdump2.x86_64 #1 >[ 2.840671] Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9, BIOS P89 07/21/2019 >[ 2.840671] RIP: 0010:domain_get_iommu+0x55/0x60 >[ 2.840671] Code: c2 01 eb 0b 48 83 c0 01 8b 34 87 85 f6 75 0b 48 63 c8 48 39 c2 75 ed 31 c0 c3 48 c1 e1 03 48 8b 05 70 f3 91 01 48 8b 04 08 c3 <0f> 0b 31 c0 c3 31 c9 eb eb 66 90 0f 1f 44 00 00 41 55 40 0f b6 f6 >[ 2.840671] RSP: 0018:ffffc900000dfab8 EFLAGS: 00010202 >[ 2.840671] RAX: ffff88ec7f1c8000 RBX: 0000006c7c867000 RCX: 0000000000000000 >[ 2.840671] RDX: 00000000fffffff0 RSI: 0000000000000000 RDI: ffff88ec7f1c8000 >[ 2.840671] RBP: ffff88ec6f7000b0 R08: ffff88ec7f19d000 R09: ffff88ec7cbfcd00 >[ 2.840671] R10: 0000000000000095 R11: ffffc900000df928 R12: 0000000000000000 >[ 2.840671] R13: ffff88ec7f1c8000 R14: 0000000000001000 R15: 00000000ffffffff >[ 2.840671] FS: 0000000000000000(0000) GS:ffff88ec7f600000(0000) knlGS:0000000000000000 >[ 2.840671] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 >[ 2.840671] CR2: 00007ff3e1713000 CR3: 0000006c7de0a004 CR4: 00000000001606b0 >[ 2.840671] Call Trace: >[ 2.840671] __intel_map_single+0x62/0x140 >[ 2.840671] intel_alloc_coherent+0xa6/0x130 >[ 2.840671] dma_pool_alloc+0xd8/0x1e0 >[ 2.840671] e_qh_alloc+0x55/0x130 >[ 2.840671] ehci_setup+0x284/0x7b0 >[ 2.840671] ehci_pci_setup+0xa3/0x530 >[ 2.840671] usb_add_hcd+0x2b6/0x800 >[ 2.840671] usb_hcd_pci_probe+0x375/0x460 >[ 2.840671] local_pci_probe+0x41/0x90 >[ 2.840671] pci_device_probe+0x105/0x1b0 >[ 2.840671] driver_probe_device+0x12d/0x460 >[ 2.840671] device_driver_attach+0x50/0x60 >[ 2.840671] __driver_attach+0x61/0x130 >[ 2.840671] ? device_driver_attach+0x60/0x60 >[ 2.840671] bus_for_each_dev+0x77/0xc0 >[ 2.840671] ? klist_add_tail+0x3b/0x70 >[ 2.840671] bus_add_driver+0x14d/0x1e0 >[ 2.840671] ? ehci_hcd_init+0xaa/0xaa >[ 2.840671] ? do_early_param+0x91/0x91 >[ 2.840671] driver_register+0x6b/0xb0 >[ 2.840671] ? ehci_hcd_init+0xaa/0xaa >[ 2.840671] do_one_initcall+0x46/0x1c3 >[ 2.840671] ? do_early_param+0x91/0x91 >[ 2.840671] kernel_init_freeable+0x1af/0x258 >[ 2.840671] ? rest_init+0xaa/0xaa >[ 2.840671] kernel_init+0xa/0xf9 >[ 2.840671] ret_from_fork+0x35/0x40 >[ 2.840671] ---[ end trace e87b0d9a1c8135c4 ]--- >[ 3.010848] ehci-pci 0000:00:1a.0: Using iommu dma mapping >[ 3.012551] ehci-pci 0000:00:1a.0: 32bit DMA uses non-identity mapping >[ 3.018537] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported >[ 3.021188] ehci-pci 0000:00:1a.0: irq 18, io mem 0x93002000 >[ 3.029006] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 >[ 3.030918] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18 >[ 3.033491] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 >[ 3.035900] usb usb1: Product: EHCI Host Controller >[ 3.037423] usb usb1: Manufacturer: Linux 4.18.0-170.el8.kdump2.x86_64 ehci_hcd >[ 3.039691] usb usb1: SerialNumber: 0000:00:1a.0 > >It looks like the device finishes initializing once it figures out it >needs dma mapping instead of the default >passthrough. intel_alloc_coherent calls iommu_need_mapping, before it >calls __intel_map_single, so I'm not sure why it is tripping over the >WARN_ON in domain_get_iommu. > >one thing I noticed while looking at this is that domain_get_iommu can >return NULL. So should there be something like the following in >__intel_map_single after the domain_get_iommu call? > >if (!iommu) > goto error; > >It is possible to deref the null pointer later otherwise. > >Regards, >Jerry
I reproduced the warning with a 5.5 kernel on an Intel NUC5i5MYBE.
| |