lkml.org 
[lkml]   [2020]   [Dec]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v4 4/7] power: supply: max8997_charger: Set CHARGER current limit
On Fri, Dec 25, 2020 at 11:33:21AM +0000, Timon Baetz wrote:
> On Thu, 24 Dec 2020 15:00:38 +0100, Krzysztof Kozlowski wrote:
> > On Thu, Dec 24, 2020 at 02:37:06PM +0100, Krzysztof Kozlowski wrote:
> > > On Thu, Dec 24, 2020 at 01:13:02PM +0000, Timon Baetz wrote:
> > > > On Thu, 24 Dec 2020 10:55:59 +0100, Krzysztof Kozlowski wrote:
> > > > > > @@ -170,6 +237,28 @@ static int max8997_battery_probe(struct platform_device *pdev)
> > > > > > return PTR_ERR(charger->battery);
> > > > > > }
> > > > > >
> > > > > > + charger->reg = devm_regulator_get(&pdev->dev, "charger");
> > > > >
> > > > > Since you do not use get_optional, you will always get a dummy
> > > > > regulator. In case of error, you should either print it or entirely fail
> > > > > the probe. Silently continuing makes it difficult to spot errors.
> > > > >
> > > > > Since the driver could operate in case of extcon/regulator error, just
> > > > > dev_err() so failure will be spotted with dmesg.
> > > >
> > > > I will switch to devm_regulator_get_optional() and print an error on
> > > > failure, thanks.
> > > >
> > > > > It will complain on older DTBs because you are introducing incompatible
> > > > > change, but that's expected. Just correct all other in-tree DTS.
> > > >
> > > > The other 2 in-tree DTS don't have CHARGER regulators. Not sure
> > > > how to correct those. Should I add muic and charger nodes without a
> > > > charger-supply? It will still complain in that case.
> > >
> > > +Cc Marek,
> > >
> > > This is why leaving the code as is - devm_regulator_get(), not optional
> > > - makes sense. Core would provide dummy regulator, so you only have to
> > > provide MUIC node.
> > >
> > > If you change the code to devm_regulator_get_optional(), you need to add
> > > everything: the charger regulator, the charger node and MUIC node.
> > >
> > > For Trats, the configuration should be similar as i9100, although I
> > > don't know the exact values of chargign voltage.
> > >
> > > For Origen, there is no battery, so the power supply should not bind.
> > > Maybe this could be achieved with "status disabled" for charger node? It
> > > depends whether MFD will respect such field... If it disables the
> > > charger, you're done.
> >
> > I just looked at the MFD code and tested it - it nicely skips disabled
> > devices. Therefore, for Origen I propose to add disabled nodes for
> > charger and MUIC because these pins are not connected. No need to add
> > regulators in such case.
>
> With a dummy regulator regulator_set_current_limit() fails with -EINVAL.

Good point.

> Isn't it better to just skip charging control (and dev_info()) when there
> is no extcon or regulator? The charger driver would still probe
> without those 2 properties and work as before.

Yes, makes sense.

>
> Adding disabled nodes for Origen would probably still makes sense.
>
> I also noticed that adding nodes for those MFD cells prints "DMA mask
> not set" which seems to be related to https://lkml.org/lkml/2020/4/23/873.
> Any suggestions on how to handle that?

I don't think it is your problem to solve. It affects other MFD devices
as well.

Best regards,
Krzysztof
\
 
 \ /
  Last update: 2020-12-28 11:34    [W:0.074 / U:0.328 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site