lkml.org 
[lkml]   [2020]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6 5/6] dt-bindings: spi: Convert cadence-quadspi.txt to cadence-quadspi.yaml
From
Date
Hi Rob,

On 5/11/2020 6:02 am, Rob Herring wrote:
> On Mon, Nov 02, 2020 at 01:59:41PM +0800, Ramuthevar, Vadivel MuruganX wrote:
>> Hi Rob,
>>
>> Thank you for the review comments...
>>
>> On 30/10/2020 11:18 pm, Rob Herring wrote:
>>> On Fri, Oct 30, 2020 at 01:31:52PM +0800, Ramuthevar,Vadivel MuruganX wrote:
>>>> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>>>>
>>>> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
>>>> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
>>>>
>>>> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>>>> ---
>>>> .../devicetree/bindings/spi/cadence-quadspi.txt | 67 ---------
>>>> .../devicetree/bindings/spi/cadence-quadspi.yaml | 149 +++++++++++++++++++++
>>>> 2 files changed, 149 insertions(+), 67 deletions(-)
>>>> delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>>>> create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>>>> deleted file mode 100644
>>>> index 945be7d5b236..000000000000
>>>> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>>>> +++ /dev/null
>>>> @@ -1,67 +0,0 @@
>>>> -* Cadence Quad SPI controller
>>>> -
>>>> -Required properties:
>>>> -- compatible : should be one of the following:
>>>> - Generic default - "cdns,qspi-nor".
>>>> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
>>>> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
>>>> -- reg : Contains two entries, each of which is a tuple consisting of a
>>>> - physical address and length. The first entry is the address and
>>>> - length of the controller register set. The second entry is the
>>>> - address and length of the QSPI Controller data area.
>>>> -- interrupts : Unit interrupt specifier for the controller interrupt.
>>>> -- clocks : phandle to the Quad SPI clock.
>>>> -- cdns,fifo-depth : Size of the data FIFO in words.
>>>> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
>>>> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
>>>> -
>>>> -Optional properties:
>>>> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
>>>> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
>>>> - the read data rather than the QSPI clock. Make sure that QSPI return
>>>> - clock is populated on the board before using this property.
>>>> -
>>>> -Optional subnodes:
>>>> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
>>>> -custom properties:
>>>> -- cdns,read-delay : Delay for read capture logic, in clock cycles
>>>> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
>>>> - mode chip select outputs are de-asserted between
>>>> - transactions.
>>>> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
>>>> - de-activated and the activation of another.
>>>> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
>>>> - transaction and deasserting the device chip select
>>>> - (qspi_n_ss_out).
>>>> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
>>>> - and first bit transfer.
>>>> -- resets : Must contain an entry for each entry in reset-names.
>>>> - See ../reset/reset.txt for details.
>>>> -- reset-names : Must include either "qspi" and/or "qspi-ocp".
>>>> -
>>>> -Example:
>>>> -
>>>> - qspi: spi@ff705000 {
>>>> - compatible = "cdns,qspi-nor";
>>>> - #address-cells = <1>;
>>>> - #size-cells = <0>;
>>>> - reg = <0xff705000 0x1000>,
>>>> - <0xffa00000 0x1000>;
>>>> - interrupts = <0 151 4>;
>>>> - clocks = <&qspi_clk>;
>>>> - cdns,is-decoded-cs;
>>>> - cdns,fifo-depth = <128>;
>>>> - cdns,fifo-width = <4>;
>>>> - cdns,trigger-address = <0x00000000>;
>>>> - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
>>>> - reset-names = "qspi", "qspi-ocp";
>>>> -
>>>> - flash0: n25q00@0 {
>>>> - ...
>>>> - cdns,read-delay = <4>;
>>>> - cdns,tshsl-ns = <50>;
>>>> - cdns,tsd2d-ns = <50>;
>>>> - cdns,tchsh-ns = <4>;
>>>> - cdns,tslch-ns = <4>;
>>>> - };
>>>> - };
>>>> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>>>> new file mode 100644
>>>> index 000000000000..ec22b040d804
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>>>> @@ -0,0 +1,149 @@
>>>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>>>> +%YAML 1.2
>>>> +---
>>>> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>>> +
>>>> +title: Cadence Quad SPI controller
>>>> +
>>>> +maintainers:
>>>> + - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com>
>>>> +
>>>> +allOf:
>>>> + - $ref: "spi-controller.yaml#"
>>>> +
>>>> +properties:
>>>> + compatible:
>>>> + oneOf:
>>>> + - items:
>>>
>>> You don't need 'oneOf' if there is only one entry...
>>>
>>> So you've dropped 'cdns,qspi-nor' alone being valid. Granted, the txt
>>> file was fuzzy as to whether or not that was valid. So you have to look
>>> at all the dts files and see. I prefer we don't allow that and require a
>>> more specific compatible, but if there's a bunch then we should allow
>>> for it. The commit message should summarize what you decide.
>> we need bunch of compatibles as below, TI, Altera and Intel uses different
>> compatible's so we added 'oneOf'.
>
> Then you add oneOf when you need it. You don't for what you wrote,
> but once it is correct you will as Altera uses 'cdns,qspi-nor' alone.
Yes, yo're right , we need oneOf in the case of adding 'cadence,qspi'
and 'cdns,qspi-nor' two different group of items.
>
>> cdns,qspi-nor can be dropped instead I can add cadence,qspi ,because this
>> driver suuports qspi-nor and qspi-nand as well.
>
> No, you can't change it because it is an ABI.
Ok, Got it, thanks!

Regards
Vadivel
>
>>
>> Sure, let me go through other documentation files for reference.
>>
>>>
>>>> + - enum:
>>>> + - ti,k2g-qspi
>>>> + - ti,am654-ospi
>>>> + - const: cdns,qspi-nor
>>>
>>>> +examples:
>>>> + - |
>>>> + qspi: spi@ff705000 {
>>>> + compatible = "cadence,qspi","cdns,qpsi-nor";
>>>
>>> And you missed fixing this.
>> Yes, fixed by "cadence,qspi" keeping alone, need to remove cdns,qspi-nor,
>> thanks!
>
> Nope!
>
> Rob
>

\
 
 \ /
  Last update: 2020-11-09 02:41    [W:0.073 / U:0.832 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site