lkml.org 
[lkml]   [2020]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH 1/2] MIPS: Ingenic: Add missing nodes for Ingenic SoCs and boards.
From
Date

On 2020/11/8 下午10:35, H. Nikolaus Schaller wrote:
>> Am 08.11.2020 um 13:46 schrieb Zhou Yanjie <zhouyanjie@wanyeetech.com>:
>>
>> Hello Nikolaus,
>>
>> On 2020/11/8 上午3:03, H. Nikolaus Schaller wrote:
>>>> Am 07.11.2020 um 12:52 schrieb 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>:
>>>>
>>>> 1.Add OTG/OTG PHY/RNG nodes for JZ4780, CGU/OTG nodes for CI20.
>>>> 2.Add OTG/OTG PHY/RNG/OST nodes for X1000, SSI/CGU/OST/OTG/SC16IS752
>>>> nodes for CU1000-Neo.
>>>> 3.Add OTG/OTG PHY/DTRNG/OST nodes for X1830, SSI/CGU/OST/OTG/SC16IS752
>>>> nodes for CU1830-Neo.
>>>>
>>>> Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
>>> Comments below for CI20 / jz4780 only.
>>>
>>> I tried to test on top of my v5.10 working tree but the CI20 does not boot any more.
>>> Maybe the SMP hacks are in the way and I have to remove them first or try on top
>>> of v5.9.y
>>
>> SMP is not available on the mainline now, so the previous SMP patch needs to be removed.
> I have tried with CONFIG_SMP disabled and now I can boot my v5.10-rc2 (plus local patches).
> And can confirm that the OTG port works.


Nice to hear it.


> (BTW: dm9000 defers probing forever but that is an unrelated issue).


On my side , it will work normally after selecting CONFIG_JZ4780_EFUSE.


>> The new SMP patch will take some time because it needs to ensure support for the new X2000 processor.
> Ok, I see. It is a little sad since it works find until 5.9 but now is broken and means we
> have to test v5.10ff with only one processor. Any hints what should be hacked to make it
> work until a final solution becomes available in upstream?


I can try to make a version that supports JZ4780 first, and I will send
it to you when it is completed.


>>
>> Thanks and best regards!
> If you like you can add my
>
> Tested by: H. Nikolaus Schaller <hns@goldelico.com> # CI20/jz4780
>
> to this patch.


Sure, I will add it to the next version.


BTW, have you noticed the problem with the MMC of JZ4780? This was first
discovered by Paul. After he told me, I also tested it. When MMC has a
relatively heavy load, there will indeed be many error messages related
to mmcblk, and it is often accompanied by file system damage.

In addition, when doing some heavy work (such as compiling docker
locally), the following warning message will be accompanied (this
problem also exists on X1830):

[ 4361.724410] warn_alloc: 1 callbacks suppressed
[ 4361.724427] go: page allocation failure: order:5,
mode:0x40cc0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
[ 4361.740945] CPU: 0 PID: 6792 Comm: go Tainted: G W         5.10.0-rc1+ #3
[ 4361.748407] Stack : 80960000 801686ec 00000000 80879d2c 00000000
00000001 00000400 801688f8
[ 4361.756845]         00000000 00000000 00000000 810891ca 84405c54
00000001 84405be8 810891ca
[ 4361.765281]         00000000 00000000 8086054c 00000003 00000001
84405abc 00000000 00001cf1
[ 4361.773717]         bff4ffd7 2c29ee2f 84405ab4 2e352020 808f0000
80000000 00000000 80860000
[ 4361.782153]         00000000 00000840 00000027 00000001 00000000
80441e34 017f02df 017f031f
[ 4361.790588]         ...
[ 4361.793064] Call Trace:
[ 4361.795547] [<80108bd4>] show_stack+0x6c/0x12c
[ 4361.800023] [<80677974>] dump_stack+0xa0/0xd0
[ 4361.804406] [<801f9e30>] warn_alloc+0xa8/0x130
[ 4361.808875] [<801fa7ac>] __alloc_pages_nodemask+0x8d4/0x908
[ 4361.814476] [<802076bc>] ____cache_alloc+0x2b4/0x600
[ 4361.819467] [<80207de8>] __kmalloc+0x90/0x120
[ 4361.823854] [<80296c8c>] proc_sys_call_handler+0xe4/0x230
[ 4361.829280] [<8021901c>] vfs_read+0x12c/0x19c
[ 4361.833662] [<802192c0>] ksys_read+0x80/0xe0
[ 4361.837960] [<80110fb8>] syscall_common+0x34/0x58
[ 4361.842687]
[ 4361.854888] Mem-Info:
[ 4361.858734] active_anon:240 inactive_anon:11673 isolated_anon:0
[ 4361.858734]  active_file:104199 inactive_file:53064 isolated_file:0
[ 4361.858734]  unevictable:0 dirty:366 writeback:0
[ 4361.858734]  slab_reclaimable:15980 slab_unreclaimable:2599
[ 4361.858734]  mapped:9755 shmem:3251 pagetables:229 bounce:0
[ 4361.858734]  free:67531 free_pcp:71 free_cma:3073
[ 4361.915078] Node 0 active_anon:960kB inactive_anon:46708kB
active_file:416796kB inactive_file:212268kB unevictable:0kB
isolated(anon):0kB isolated(file):0kB mapped:39024kB dirty:1476kB
writeback:0kB shmem:13004kB writeback_tmp:0kB kernel_stack:600kB
all_unreclaimable? no
[ 4361.940604] Normal free:33244kB min:1956kB low:2444kB high:2932kB
reserved_highatomic:0KB active_anon:0kB inactive_anon:156kB
active_file:82176kB inactive_file:47128kB unevictable:0kB
writepending:1228kB present:262144kB managed:239444kB mlocked:0kB
pagetables:908kB bounce:0kB free_pcp:120kB local_pcp:120kB free_cma:12300kB
[ 4361.940612] lowmem_reserve[]: 0 6144 0
[ 4361.974937] HighMem free:236820kB min:512kB low:2116kB high:3720kB
reserved_highatomic:0KB active_anon:960kB inactive_anon:46552kB
active_file:334620kB inactive_file:165140kB unevictable:0kB
writepending:248kB present:786432kB managed:786432kB mlocked:0kB
pagetables:0kB bounce:0kB free_pcp:240kB local_pcp:240kB free_cma:0kB
[ 4361.974944] lowmem_reserve[]: 0 0 0
[ 4362.008189] Normal: 2127*4kB (UMEC) 1508*8kB (UMEC) 472*16kB (UMEC)
96*32kB (UMC) 12*64kB (C) 4*128kB (C) 1*256kB (C) 1*512kB (C) 0*1024kB
0*2048kB 0*4096kB = 33244kB
[ 4362.024364] HighMem: 1441*4kB (UM) 5376*8kB (UM) 3637*16kB (UM)
1210*32kB (UM) 498*64kB (UM) 225*128kB (UM) 69*256kB (UM) 23*512kB (UM)
1*1024kB (M) 0*2048kB 0*4096kB = 236820kB
[ 4362.041152] 160520 total pagecache pages
[ 4362.045838] 0 pages in swap cache
[ 4362.049187] Swap cache stats: add 0, delete 0, find 0/0
[ 4362.055501] Free swap  = 0kB
[ 4362.058413] Total swap = 0kB
[ 4362.061315] 262144 pages RAM
[ 4362.065588] 196608 pages HighMem/MovableOnly
[ 4362.069889] 5675 pages reserved
[ 4362.074159] 8192 pages cma reserved

Do you have any idea?


Thanks and best regards!


>>
>>>> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>>>> ---
>>>> arch/mips/boot/dts/ingenic/ci20.dts | 16 +++++++++
>>>> arch/mips/boot/dts/ingenic/cu1000-neo.dts | 60 +++++++++++++++++++++++++++----
>>>> arch/mips/boot/dts/ingenic/cu1830-neo.dts | 60 +++++++++++++++++++++++++++----
>>>> arch/mips/boot/dts/ingenic/jz4780.dtsi | 41 +++++++++++++++++++--
>>>> arch/mips/boot/dts/ingenic/x1000.dtsi | 52 ++++++++++++++++++++++++++-
>>>> arch/mips/boot/dts/ingenic/x1830.dtsi | 54 +++++++++++++++++++++++++++-
>>>> 6 files changed, 267 insertions(+), 16 deletions(-)
>>>>
>>>> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
>>>> index 75f5bfbf2c37..b31054a41754 100644
>>>> --- a/arch/mips/boot/dts/ingenic/ci20.dts
>>>> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
>>>> @@ -93,6 +93,15 @@
>>>> clock-frequency = <48000000>;
>>>> };
>>>>
>>>> +&cgu {
>>>> + /*
>>>> + * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
>>>> + * precision.
>>>> + */
>>>> + assigned-clocks = <&cgu JZ4780_CLK_RTC>;
>>>> + assigned-clock-parents = <&cgu JZ4780_CLK_RTCLK>;
>>>> +};
>>>> +
>>> ok
>>>
>>>> &mmc0 {
>>>> status = "okay";
>>>>
>>>> @@ -396,6 +405,13 @@
>>>> status = "okay";
>>>> };
>>>>
>>>> +&otg {
>>>> + status = "okay";
>>>> +
>>>> + assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>;
>>>> + assigned-clock-rates = <48000000>;
>>>> +};
>>>> +
>>> ok
>>>
>>>> &pinctrl {
>>>> pins_uart0: uart0 {
>>>> function = "uart0";
>>>> diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
>>>> index 22a1066d637b..44d47d12db12 100644
>>>> --- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
>>>> +++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
>>>> @@ -3,7 +3,7 @@
>>>>
>>>> #include "x1000.dtsi"
>>>> #include <dt-bindings/gpio/gpio.h>
>>>> -#include <dt-bindings/clock/ingenic,tcu.h>
>>>> +#include <dt-bindings/clock/ingenic,sysost.h>
>>>> #include <dt-bindings/interrupt-controller/irq.h>
>>>>
>>>> / {
>>>> @@ -31,6 +31,18 @@
>>>> };
>>>> };
>>>>
>>>> + ssi: spi-gpio {
>>>> + compatible = "spi-gpio";
>>>> + #address-cells = <1>;
>>>> + #size-cells = <0>;
>>>> + num-chipselects = <1>;
>>>> +
>>>> + mosi-gpios = <&gpd 2 GPIO_ACTIVE_HIGH>;
>>>> + miso-gpios = <&gpd 3 GPIO_ACTIVE_HIGH>;
>>>> + sck-gpios = <&gpd 0 GPIO_ACTIVE_HIGH>;
>>>> + cs-gpios = <&gpd 1 GPIO_ACTIVE_HIGH>;
>>>> + };
>>>> +
>>>> wlan_pwrseq: msc1-pwrseq {
>>>> compatible = "mmc-pwrseq-simple";
>>>>
>>>> @@ -43,13 +55,19 @@
>>>> clock-frequency = <24000000>;
>>>> };
>>>>
>>>> -&tcu {
>>>> +&cgu {
>>>> + /*
>>>> + * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
>>>> + * precision.
>>>> + */
>>>> + assigned-clocks = <&cgu X1000_CLK_RTC>;
>>>> + assigned-clock-parents = <&cgu X1000_CLK_RTCLK>;
>>>> +};
>>>> +
>>>> +&ost {
>>>> /* 1500 kHz for the system timer and clocksource */
>>>> - assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
>>>> + assigned-clocks = <&ost OST_CLK_PERCPU_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
>>>> assigned-clock-rates = <1500000>, <1500000>;
>>>> -
>>>> - /* Use channel #0 for the system timer channel #2 for the clocksource */
>>>> - ingenic,pwm-channels-mask = <0xfa>;
>>>> };
>>>>
>>>> &uart2 {
>>>> @@ -59,6 +77,32 @@
>>>> pinctrl-0 = <&pins_uart2>;
>>>> };
>>>>
>>>> +&ssi {
>>>> + status = "okay";
>>>> +
>>>> + spi-max-frequency = <50000000>;
>>>> +
>>>> + sc16is752: expander@0 {
>>>> + compatible = "nxp,sc16is752";
>>>> + reg = <0>; /* CE0 */
>>>> + spi-max-frequency = <4000000>;
>>>> +
>>>> + clocks = <&exclk_sc16is752>;
>>>> +
>>>> + interrupt-parent = <&gpc>;
>>>> + interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
>>>> +
>>>> + gpio-controller;
>>>> + #gpio-cells = <2>;
>>>> +
>>>> + exclk_sc16is752: sc16is752 {
>>>> + compatible = "fixed-clock";
>>>> + #clock-cells = <0>;
>>>> + clock-frequency = <48000000>;
>>>> + };
>>>> + };
>>>> +};
>>>> +
>>>> &i2c0 {
>>>> status = "okay";
>>>>
>>>> @@ -135,6 +179,10 @@
>>>> };
>>>> };
>>>>
>>>> +&otg {
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> &pinctrl {
>>>> pins_uart2: uart2 {
>>>> function = "uart2";
>>>> diff --git a/arch/mips/boot/dts/ingenic/cu1830-neo.dts b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
>>>> index 640f96c00d63..7a56e344e429 100644
>>>> --- a/arch/mips/boot/dts/ingenic/cu1830-neo.dts
>>>> +++ b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
>>>> @@ -3,7 +3,7 @@
>>>>
>>>> #include "x1830.dtsi"
>>>> #include <dt-bindings/gpio/gpio.h>
>>>> -#include <dt-bindings/clock/ingenic,tcu.h>
>>>> +#include <dt-bindings/clock/ingenic,sysost.h>
>>>> #include <dt-bindings/interrupt-controller/irq.h>
>>>>
>>>> / {
>>>> @@ -31,6 +31,18 @@
>>>> };
>>>> };
>>>>
>>>> + ssi0: spi-gpio {
>>>> + compatible = "spi-gpio";
>>>> + #address-cells = <1>;
>>>> + #size-cells = <0>;
>>>> + num-chipselects = <1>;
>>>> +
>>>> + mosi-gpios = <&gpc 12 GPIO_ACTIVE_HIGH>;
>>>> + miso-gpios = <&gpc 11 GPIO_ACTIVE_HIGH>;
>>>> + sck-gpios = <&gpc 15 GPIO_ACTIVE_HIGH>;
>>>> + cs-gpios = <&gpc 16 GPIO_ACTIVE_HIGH>;
>>>> + };
>>>> +
>>>> wlan_pwrseq: msc1-pwrseq {
>>>> compatible = "mmc-pwrseq-simple";
>>>>
>>>> @@ -43,13 +55,19 @@
>>>> clock-frequency = <24000000>;
>>>> };
>>>>
>>>> -&tcu {
>>>> +&cgu {
>>>> + /*
>>>> + * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
>>>> + * precision.
>>>> + */
>>>> + assigned-clocks = <&cgu X1830_CLK_RTC>;
>>>> + assigned-clock-parents = <&cgu X1830_CLK_RTCLK>;
>>>> +};
>>>> +
>>>> +&ost {
>>>> /* 1500 kHz for the system timer and clocksource */
>>>> - assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
>>>> + assigned-clocks = <&ost OST_CLK_PERCPU_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
>>>> assigned-clock-rates = <1500000>, <1500000>;
>>>> -
>>>> - /* Use channel #0 for the system timer channel #2 for the clocksource */
>>>> - ingenic,pwm-channels-mask = <0xfa>;
>>>> };
>>>>
>>>> &uart1 {
>>>> @@ -59,6 +77,32 @@
>>>> pinctrl-0 = <&pins_uart1>;
>>>> };
>>>>
>>>> +&ssi0 {
>>>> + status = "okay";
>>>> +
>>>> + spi-max-frequency = <50000000>;
>>>> +
>>>> + sc16is752: expander@0 {
>>>> + compatible = "nxp,sc16is752";
>>>> + reg = <0>; /* CE0 */
>>>> + spi-max-frequency = <4000000>;
>>>> +
>>>> + clocks = <&exclk_sc16is752>;
>>>> +
>>>> + interrupt-parent = <&gpb>;
>>>> + interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
>>>> +
>>>> + gpio-controller;
>>>> + #gpio-cells = <2>;
>>>> +
>>>> + exclk_sc16is752: sc16is752 {
>>>> + compatible = "fixed-clock";
>>>> + #clock-cells = <0>;
>>>> + clock-frequency = <48000000>;
>>>> + };
>>>> + };
>>>> +};
>>>> +
>>>> &i2c0 {
>>>> status = "okay";
>>>>
>>>> @@ -135,6 +179,10 @@
>>>> };
>>>> };
>>>>
>>>> +&otg {
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> &pinctrl {
>>>> pins_uart1: uart1 {
>>>> function = "uart1";
>>>> diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
>>>> index dfb5a7e1bb21..8837147e5a84 100644
>>>> --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
>>>> +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
>>>> @@ -61,13 +61,30 @@
>>>> };
>>>>
>>>> cgu: jz4780-cgu@10000000 {
>>>> - compatible = "ingenic,jz4780-cgu";
>>>> + compatible = "ingenic,jz4780-cgu", "simple-mfd";
>>>> reg = <0x10000000 0x100>;
>>>> + #address-cells = <1>;
>>>> + #size-cells = <1>;
>>>> + ranges = <0x0 0x10000000 0x100>;
>>>> +
>>>> + #clock-cells = <1>;
>>>>
>>>> clocks = <&ext>, <&rtc>;
>>>> clock-names = "ext", "rtc";
>>>>
>>>> - #clock-cells = <1>;
>>>> + otg_phy: usb-phy@3c {
>>>> + compatible = "ingenic,jz4780-phy";
>>>> + reg = <0x3c 0x10>;
>>>> +
>>>> + clocks = <&cgu JZ4780_CLK_OTG1>;
>>>> +
>>>> + #phy-cells = <0>;
>>>> + };
>>>> +
>>>> + rng: rng@d8 {
>>>> + compatible = "ingenic,jz4780-rng";
>>>> + reg = <0xd8 0x8>;
>>>> + };
>>>> };
>>>>
>>>> tcu: timer@10002000 {
>>>> @@ -494,4 +511,24 @@
>>>>
>>>> status = "disabled";
>>>> };
>>>> +
>>>> + otg: usb@13500000 {
>>>> + compatible = "ingenic,jz4780-otg", "snps,dwc2";
>>>> + reg = <0x13500000 0x40000>;
>>>> +
>>>> + interrupt-parent = <&intc>;
>>>> + interrupts = <21>;
>>>> +
>>>> + clocks = <&cgu JZ4780_CLK_UHC>;
>>>> + clock-names = "otg";
>>>> +
>>>> + phys = <&otg_phy>;
>>>> + phy-names = "usb2-phy";
>>>> +
>>>> + g-rx-fifo-size = <768>;
>>> I had tested with 256 before and do not see a reason why 768 should not work as well.
>>>
>>>> + g-np-tx-fifo-size = <256>;
>>>> + g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
>>>> +
>>>> + status = "disabled";
>>>> + };
>>>> };
>>>> diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
>>>> index 1f1f896dd1f7..854fac58f45e 100644
>>>> --- a/arch/mips/boot/dts/ingenic/x1000.dtsi
>>>> +++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
>>>> @@ -52,13 +52,43 @@
>>>> };
>>>>
>>>> cgu: x1000-cgu@10000000 {
>>>> - compatible = "ingenic,x1000-cgu";
>>>> + compatible = "ingenic,x1000-cgu", "simple-mfd";
>>>> reg = <0x10000000 0x100>;
>>>> + #address-cells = <1>;
>>>> + #size-cells = <1>;
>>>> + ranges = <0x0 0x10000000 0x100>;
>>>>
>>>> #clock-cells = <1>;
>>>>
>>>> clocks = <&exclk>, <&rtclk>;
>>>> clock-names = "ext", "rtc";
>>>> +
>>>> + otg_phy: usb-phy@3c {
>>>> + compatible = "ingenic,x1000-phy";
>>>> + reg = <0x3c 0x10>;
>>>> +
>>>> + clocks = <&cgu X1000_CLK_OTGPHY>;
>>>> +
>>>> + #phy-cells = <0>;
>>>> + };
>>>> +
>>>> + rng: rng@d8 {
>>>> + compatible = "ingenic,x1000-rng";
>>>> + reg = <0xd8 0x8>;
>>>> + };
>>>> + };
>>>> +
>>>> + ost: timer@12000000 {
>>>> + compatible = "ingenic,x1000-ost";
>>>> + reg = <0x12000000 0x3c>;
>>>> +
>>>> + #clock-cells = <1>;
>>>> +
>>>> + clocks = <&cgu X1000_CLK_OST>;
>>>> + clock-names = "ost";
>>>> +
>>>> + interrupt-parent = <&cpuintc>;
>>>> + interrupts = <3>;
>>>> };
>>>>
>>>> tcu: timer@10002000 {
>>>> @@ -323,4 +353,24 @@
>>>> status = "disabled";
>>>> };
>>>> };
>>>> +
>>>> + otg: usb@13500000 {
>>>> + compatible = "ingenic,x1000-otg", "snps,dwc2";
>>>> + reg = <0x13500000 0x40000>;
>>>> +
>>>> + interrupt-parent = <&intc>;
>>>> + interrupts = <21>;
>>>> +
>>>> + clocks = <&cgu X1000_CLK_OTG>;
>>>> + clock-names = "otg";
>>>> +
>>>> + phys = <&otg_phy>;
>>>> + phy-names = "usb2-phy";
>>>> +
>>>> + g-rx-fifo-size = <768>;
>>>> + g-np-tx-fifo-size = <256>;
>>>> + g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
>>>> +
>>>> + status = "disabled";
>>>> + };
>>>> };
>>>> diff --git a/arch/mips/boot/dts/ingenic/x1830.dtsi b/arch/mips/boot/dts/ingenic/x1830.dtsi
>>>> index b05dac3ae308..4831350efdf2 100644
>>>> --- a/arch/mips/boot/dts/ingenic/x1830.dtsi
>>>> +++ b/arch/mips/boot/dts/ingenic/x1830.dtsi
>>>> @@ -52,13 +52,38 @@
>>>> };
>>>>
>>>> cgu: x1830-cgu@10000000 {
>>>> - compatible = "ingenic,x1830-cgu";
>>>> + compatible = "ingenic,x1830-cgu", "simple-mfd";
>>>> reg = <0x10000000 0x100>;
>>>> + #address-cells = <1>;
>>>> + #size-cells = <1>;
>>>> + ranges = <0x0 0x10000000 0x100>;
>>>>
>>>> #clock-cells = <1>;
>>>>
>>>> clocks = <&exclk>, <&rtclk>;
>>>> clock-names = "ext", "rtc";
>>>> +
>>>> + otg_phy: usb-phy@3c {
>>>> + compatible = "ingenic,x1830-phy";
>>>> + reg = <0x3c 0x10>;
>>>> +
>>>> + clocks = <&cgu X1830_CLK_OTGPHY>;
>>>> +
>>>> + #phy-cells = <0>;
>>>> + };
>>>> + };
>>>> +
>>>> + ost: timer@12000000 {
>>>> + compatible = "ingenic,x1830-ost", "ingenic,x1000-ost";
>>>> + reg = <0x12000000 0x3c>;
>>>> +
>>>> + #clock-cells = <1>;
>>>> +
>>>> + clocks = <&cgu X1830_CLK_OST>;
>>>> + clock-names = "ost";
>>>> +
>>>> + interrupt-parent = <&cpuintc>;
>>>> + interrupts = <4>;
>>>> };
>>>>
>>>> tcu: timer@10002000 {
>>>> @@ -236,6 +261,13 @@
>>>> status = "disabled";
>>>> };
>>>>
>>>> + dtrng: trng@10072000 {
>>>> + compatible = "ingenic,x1830-dtrng";
>>>> + reg = <0x10072000 0xc>;
>>>> +
>>>> + clocks = <&cgu X1830_CLK_DTRNG>;
>>>> + };
>>>> +
>>>> pdma: dma-controller@13420000 {
>>>> compatible = "ingenic,x1830-dma";
>>>> reg = <0x13420000 0x400
>>>> @@ -311,4 +343,24 @@
>>>> status = "disabled";
>>>> };
>>>> };
>>>> +
>>>> + otg: usb@13500000 {
>>>> + compatible = "ingenic,x1830-otg", "snps,dwc2";
>>>> + reg = <0x13500000 0x40000>;
>>>> +
>>>> + interrupt-parent = <&intc>;
>>>> + interrupts = <21>;
>>>> +
>>>> + clocks = <&cgu X1830_CLK_OTG>;
>>>> + clock-names = "otg";
>>>> +
>>>> + phys = <&otg_phy>;
>>>> + phy-names = "usb2-phy";
>>>> +
>>>> + g-rx-fifo-size = <768>;
>>>> + g-np-tx-fifo-size = <256>;
>>>> + g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
>>>> +
>>>> + status = "disabled";
>>>> + };
>>>> };
>>>> --
>>>> 2.11.0
>>>>

\
 
 \ /
  Last update: 2020-11-08 16:14    [W:0.070 / U:1.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site