lkml.org 
[lkml]   [2020]   [Nov]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] bus: fsl-mc: make sure MC firmware is up and running
Date
Some bootloaders might pause the MC firmware before starting the
kernel to ensure that MC will not cause faults as soon as SMMU
probes due to no configuration being in place for the firmware.
Make sure that MC is resumed at probe time as its SMMU setup should
be done by now.
Also included, a comment fix on how PL and BMT bits are packed in
the StreamID.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 42 +++++++++++++++++++++++----------
1 file changed, 30 insertions(+), 12 deletions(-)

diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index 806766b1b45f..b8e6acdf932e 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -60,6 +60,9 @@ struct fsl_mc_addr_translation_range {
phys_addr_t start_phys_addr;
};

+#define FSL_MC_GCR1 0x0
+#define GCR1_P1_STOP BIT(31)
+
#define FSL_MC_FAPR 0x28
#define MC_FAPR_PL BIT(18)
#define MC_FAPR_BMT BIT(17)
@@ -973,21 +976,36 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
return PTR_ERR(mc->fsl_mc_regs);
}

- if (mc->fsl_mc_regs && IS_ENABLED(CONFIG_ACPI) &&
- !dev_of_node(&pdev->dev)) {
- mc_stream_id = readl(mc->fsl_mc_regs + FSL_MC_FAPR);
+ if (mc->fsl_mc_regs) {
/*
- * HW ORs the PL and BMT bit, places the result in bit 15 of
- * the StreamID and ORs in the ICID. Calculate it accordingly.
+ * Some bootloaders pause the MC firmware before booting the
+ * kernel so that MC will not cause faults as soon as the
+ * SMMU probes due to the fact that there's no configuration
+ * in place for MC.
+ * At this point MC should have all its SMMU setup done so make
+ * sure it is resumed.
*/
- mc_stream_id = (mc_stream_id & 0xffff) |
+ writel(readl(mc->fsl_mc_regs + FSL_MC_GCR1) & (~GCR1_P1_STOP),
+ mc->fsl_mc_regs + FSL_MC_GCR1);
+
+ if (IS_ENABLED(CONFIG_ACPI) && !dev_of_node(&pdev->dev)) {
+ mc_stream_id = readl(mc->fsl_mc_regs + FSL_MC_FAPR);
+ /*
+ * HW ORs the PL and BMT bit, places the result in bit
+ * 14 of the StreamID and ORs in the ICID. Calculate it
+ * accordingly.
+ */
+ mc_stream_id = (mc_stream_id & 0xffff) |
((mc_stream_id & (MC_FAPR_PL | MC_FAPR_BMT)) ?
- 0x4000 : 0);
- error = acpi_dma_configure_id(&pdev->dev, DEV_DMA_COHERENT,
- &mc_stream_id);
- if (error)
- dev_warn(&pdev->dev, "failed to configure dma: %d.\n",
- error);
+ BIT(14) : 0);
+ error = acpi_dma_configure_id(&pdev->dev,
+ DEV_DMA_COHERENT,
+ &mc_stream_id);
+ if (error)
+ dev_warn(&pdev->dev,
+ "failed to configure dma: %d.\n",
+ error);
+ }
}

/*
--
2.17.1
\
 
 \ /
  Last update: 2020-11-05 16:32    [W:0.042 / U:1.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site