lkml.org 
[lkml]   [2020]   [Nov]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 5/6] dt-bindings: spi: Convert cadence-quadspi.txt to cadence-quadspi.yaml
On Mon, Nov 02, 2020 at 01:59:41PM +0800, Ramuthevar, Vadivel MuruganX wrote:
> Hi Rob,
>
> Thank you for the review comments...
>
> On 30/10/2020 11:18 pm, Rob Herring wrote:
> > On Fri, Oct 30, 2020 at 01:31:52PM +0800, Ramuthevar,Vadivel MuruganX wrote:
> > > From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> > >
> > > Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
> > > remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
> > >
> > > Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> > > ---
> > > .../devicetree/bindings/spi/cadence-quadspi.txt | 67 ---------
> > > .../devicetree/bindings/spi/cadence-quadspi.yaml | 149 +++++++++++++++++++++
> > > 2 files changed, 149 insertions(+), 67 deletions(-)
> > > delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> > > create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> > > deleted file mode 100644
> > > index 945be7d5b236..000000000000
> > > --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> > > +++ /dev/null
> > > @@ -1,67 +0,0 @@
> > > -* Cadence Quad SPI controller
> > > -
> > > -Required properties:
> > > -- compatible : should be one of the following:
> > > - Generic default - "cdns,qspi-nor".
> > > - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> > > - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
> > > -- reg : Contains two entries, each of which is a tuple consisting of a
> > > - physical address and length. The first entry is the address and
> > > - length of the controller register set. The second entry is the
> > > - address and length of the QSPI Controller data area.
> > > -- interrupts : Unit interrupt specifier for the controller interrupt.
> > > -- clocks : phandle to the Quad SPI clock.
> > > -- cdns,fifo-depth : Size of the data FIFO in words.
> > > -- cdns,fifo-width : Bus width of the data FIFO in bytes.
> > > -- cdns,trigger-address : 32-bit indirect AHB trigger address.
> > > -
> > > -Optional properties:
> > > -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
> > > -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
> > > - the read data rather than the QSPI clock. Make sure that QSPI return
> > > - clock is populated on the board before using this property.
> > > -
> > > -Optional subnodes:
> > > -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
> > > -custom properties:
> > > -- cdns,read-delay : Delay for read capture logic, in clock cycles
> > > -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
> > > - mode chip select outputs are de-asserted between
> > > - transactions.
> > > -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
> > > - de-activated and the activation of another.
> > > -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
> > > - transaction and deasserting the device chip select
> > > - (qspi_n_ss_out).
> > > -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
> > > - and first bit transfer.
> > > -- resets : Must contain an entry for each entry in reset-names.
> > > - See ../reset/reset.txt for details.
> > > -- reset-names : Must include either "qspi" and/or "qspi-ocp".
> > > -
> > > -Example:
> > > -
> > > - qspi: spi@ff705000 {
> > > - compatible = "cdns,qspi-nor";
> > > - #address-cells = <1>;
> > > - #size-cells = <0>;
> > > - reg = <0xff705000 0x1000>,
> > > - <0xffa00000 0x1000>;
> > > - interrupts = <0 151 4>;
> > > - clocks = <&qspi_clk>;
> > > - cdns,is-decoded-cs;
> > > - cdns,fifo-depth = <128>;
> > > - cdns,fifo-width = <4>;
> > > - cdns,trigger-address = <0x00000000>;
> > > - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> > > - reset-names = "qspi", "qspi-ocp";
> > > -
> > > - flash0: n25q00@0 {
> > > - ...
> > > - cdns,read-delay = <4>;
> > > - cdns,tshsl-ns = <50>;
> > > - cdns,tsd2d-ns = <50>;
> > > - cdns,tchsh-ns = <4>;
> > > - cdns,tslch-ns = <4>;
> > > - };
> > > - };
> > > diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> > > new file mode 100644
> > > index 000000000000..ec22b040d804
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> > > @@ -0,0 +1,149 @@
> > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Cadence Quad SPI controller
> > > +
> > > +maintainers:
> > > + - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com>
> > > +
> > > +allOf:
> > > + - $ref: "spi-controller.yaml#"
> > > +
> > > +properties:
> > > + compatible:
> > > + oneOf:
> > > + - items:
> >
> > You don't need 'oneOf' if there is only one entry...
> >
> > So you've dropped 'cdns,qspi-nor' alone being valid. Granted, the txt
> > file was fuzzy as to whether or not that was valid. So you have to look
> > at all the dts files and see. I prefer we don't allow that and require a
> > more specific compatible, but if there's a bunch then we should allow
> > for it. The commit message should summarize what you decide.
> we need bunch of compatibles as below, TI, Altera and Intel uses different
> compatible's so we added 'oneOf'.

Then you add oneOf when you need it. You don't for what you wrote,
but once it is correct you will as Altera uses 'cdns,qspi-nor' alone.

> cdns,qspi-nor can be dropped instead I can add cadence,qspi ,because this
> driver suuports qspi-nor and qspi-nand as well.

No, you can't change it because it is an ABI.

>
> Sure, let me go through other documentation files for reference.
>
> >
> > > + - enum:
> > > + - ti,k2g-qspi
> > > + - ti,am654-ospi
> > > + - const: cdns,qspi-nor
> >
> > > +examples:
> > > + - |
> > > + qspi: spi@ff705000 {
> > > + compatible = "cadence,qspi","cdns,qpsi-nor";
> >
> > And you missed fixing this.
> Yes, fixed by "cadence,qspi" keeping alone, need to remove cdns,qspi-nor,
> thanks!

Nope!

Rob

\
 
 \ /
  Last update: 2020-11-04 23:03    [W:0.069 / U:0.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site