lkml.org 
[lkml]   [2020]   [Nov]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] cpuidle: Select polling interval based on a c-state with a longer target residency
On Mon, Nov 30, 2020 at 10:22 AM Mel Gorman <mgorman@techsingularity.net> wrote:
>
> It was noted that a few workloads that idle rapidly regressed when commit
> 36fcb4292473 ("cpuidle: use first valid target residency as poll time")
> was merged. The workloads in question were heavy communicators that idle
> rapidly and were impacted by the c-state exit latency as the active CPUs
> were not polling at the time of wakeup. As they were not particularly
> realistic workloads, it was not considered to be a major problem.
>
> Unfortunately, a bug was reported for a real workload in a production
> environment that relied on large numbers of threads operating in a worker
> pool pattern. These threads would idle for periods of time longer than the
> C1 target residency and so incurred the c-state exit latency penalty. The
> application is very sensitive to wakeup latency and indirectly relying
> on behaviour prior to commit on a37b969a61c1 ("cpuidle: poll_state: Add
> time limit to poll_idle()") to poll for long enough to avoid the exit
> latency cost.
>
> The target residency of C1 is typically very short. On some x86 machines,
> it can be as low as 2 microseconds. In poll_idle(), the clock is checked
> every POLL_IDLE_RELAX_COUNT interations of cpu_relax() and even one
> iteration of that loop can be over 1 microsecond so the polling interval is
> very close to the granularity of what poll_idle() can detect. Furthermore,
> a basic ping pong workload like perf bench pipe has a longer round-trip
> time than the 2 microseconds meaning that the CPU will almost certainly
> not be polling when the ping-pong completes.
>
> This patch selects a polling interval based on an enabled c-state that
> has an target residency longer than 10usec. If there is no enabled-cstate
> then polling will be up to a TICK_NSEC/16 similar to what it was up until
> kernel 4.20.
>
> As an example, consider a CPU with the following c-state information from
> an Intel CPU;
>
> residency exit_latency
> C1 2 2
> C1E 20 10
> C3 100 33
> C6 400 133
>
> The polling interval selected is 20usec. If booted with
> intel_idle.max_cstate=1 then the polling interval is 250usec as the deeper
> c-states were not available.
>
> On an AMD EPYC machine, the c-state information is more limited and looks
> like
>
> residency exit_latency
> C1 2 1
> C2 800 400
>
> The polling interval selected is 250usec. While C2 was considered, the
> polling interval was clamped by CPUIDLE_POLL_MAX.
>
> Note that it is not expected that polling will be a universal win. As
> well as potentially trading power for performance, the performance is not
> guaranteed if the extra polling prevented a turbo state being reached. The
> patch allows the polling interval to be tuned in case a corner-case is
> found and if a bug is filed, the tuning may advise how CPUIDLE_POLL_MIN
> should be adjusted (e.g. optional overrides per architecture) or if a
> different balance point than residency-exit_latency should be used.
>
> tbench4
> vanilla polling
> Hmean 1 497.89 ( 0.00%) 543.15 * 9.09%*
> Hmean 2 975.88 ( 0.00%) 1059.73 * 8.59%*
> Hmean 4 1953.97 ( 0.00%) 2081.37 * 6.52%*
> Hmean 8 3645.76 ( 0.00%) 4052.95 * 11.17%*
> Hmean 16 6882.21 ( 0.00%) 6995.93 * 1.65%*
> Hmean 32 10752.20 ( 0.00%) 10731.53 * -0.19%*
> Hmean 64 12875.08 ( 0.00%) 12478.13 * -3.08%*
> Hmean 128 21500.54 ( 0.00%) 21098.60 * -1.87%*
> Hmean 256 21253.70 ( 0.00%) 21027.18 * -1.07%*
> Hmean 320 20813.50 ( 0.00%) 20580.64 * -1.12%*
>
> Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
> ---
> Documentation/admin-guide/kernel-parameters.txt | 18 +++++++++
> drivers/cpuidle/cpuidle.c | 49 ++++++++++++++++++++++++-
> 2 files changed, 65 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
> index 526d65d8573a..5b8545022564 100644
> --- a/Documentation/admin-guide/kernel-parameters.txt
> +++ b/Documentation/admin-guide/kernel-parameters.txt
> @@ -719,6 +719,24 @@
> policy to use. This governor must be registered in the
> kernel before the cpufreq driver probes.
>
> + cpuidle.poll=
> + [CPU_IDLE]
> + Format: <int>
> + Set the time in microseconds a CPU should poll in
> + cpuidle for a new task before entering a sleep
> + state. The default is determined by either the
> + tick or the enabled c-state latencies. Tuning is
> + not generally recommended but it may be needed
> + for workloads that are both latency-sensitive
> + and idling rapidly for short durations. Limiting
> + c-states can be insufficient if the polling
> + time is still too short, the application has no
> + knowledge of /dev/cpu_dma_latency, there are
> + multiple applications or the environment does
> + not allow the installation of a userspace tool
> + that controls cpu_dma_latency. This value may
> + be ignored by the idle governor (e.g. haltpoll).

OK, we can do this, but I'd use a shorter different description here
and a more detailed one in the admin-guide documentation.

Also this is about certain drivers only which support the "polling
idle state" (the ACPI one and intel_idle only AFAICS). So I'm not
sure about the framework-level tunable here.

Moreover, to be precise, that value is the maximum time to do the
polling (in one go) in the case when requesting any "physical" idle
states is likely to hurt energy-efficiency or latency. In particular,
it doesn't mean that idle CPUs will do the idle polling every time.

> +
> cpu_init_udelay=N
> [X86] Delay for N microsec between assert and de-assert
> of APIC INIT to start processors. This delay occurs
> diff --git a/drivers/cpuidle/cpuidle.c b/drivers/cpuidle/cpuidle.c
> index 83af15f77f66..3be208e9043a 100644
> --- a/drivers/cpuidle/cpuidle.c
> +++ b/drivers/cpuidle/cpuidle.c
> @@ -368,6 +368,26 @@ void cpuidle_reflect(struct cpuidle_device *dev, int index)
> cpuidle_curr_governor->reflect(dev, index);
> }
>
> +static struct kernel_param_ops poll_param_ops = {
> + .set = param_set_ulong,
> + .get = param_get_ulong,
> +};
> +
> +/*
> + * Min polling interval of 10usec is a guess. It is assuming that
> + * for most users, the time for a single ping-pong workload like
> + * perf bench pipe would generally complete within 10usec but
> + * this is hardware dependant. Actual time can be estimated with
> + *
> + * perf bench sched pipe -l 10000
> + *
> + * Run multiple times to avoid cpufreq effects.
> + */
> +#define CPUIDLE_POLL_MIN 10000

Well, if we consider providing this tunable, we should also make it
possible to set it to 0, because the "no polling" use case is valid
too (at least AFAICS). But in the case of 0, the "polling idle state"
should be effectively disabled, so the governors don't need to bother
looking at it.

> +#define CPUIDLE_POLL_MAX (TICK_NSEC / 16)
> +
> +static unsigned long __read_mostly param_poll;
> +
> /**
> * cpuidle_poll_time - return amount of time to poll for,
> * governors can override dev->poll_limit_ns if necessary
> @@ -382,20 +402,44 @@ u64 cpuidle_poll_time(struct cpuidle_driver *drv,
> int i;
> u64 limit_ns;
>
> + BUILD_BUG_ON(CPUIDLE_POLL_MIN > CPUIDLE_POLL_MAX);
> +
> if (dev->poll_limit_ns)
> return dev->poll_limit_ns;
>
> - limit_ns = TICK_NSEC;
> + /* Use module parameter if specified */
> + if (param_poll) {
> + param_poll *= NSEC_PER_USEC;
> + param_poll = clamp_t(unsigned long, param_poll * NSEC_PER_USEC,
> + CPUIDLE_POLL_MIN, CPUIDLE_POLL_MAX);
> + limit_ns = param_poll;
> + goto out;
> + }
> +
> + limit_ns = CPUIDLE_POLL_MAX;
> for (i = 1; i < drv->state_count; i++) {
> + u64 state_limit;
> +
> if (dev->states_usage[i].disable)
> continue;
>
> - limit_ns = drv->states[i].target_residency_ns;
> + state_limit = drv->states[i].target_residency_ns;
> + if (state_limit < CPUIDLE_POLL_MIN)
> + continue;
> +
> + limit_ns = min_t(u64, state_limit, CPUIDLE_POLL_MAX);
> break;
> }
>
> +out:
> dev->poll_limit_ns = limit_ns;
>
> + /*
> + * Polling parameter reported as usec to match the values reported
> + * for c-cstate exit latencies in sysfs.
> + */
> + param_poll = div64_ul(dev->poll_limit_ns, NSEC_PER_USEC);
> +
> return dev->poll_limit_ns;
> }
>
> @@ -755,4 +799,5 @@ static int __init cpuidle_init(void)
>
> module_param(off, int, 0444);
> module_param_string(governor, param_governor, CPUIDLE_NAME_LEN, 0444);
> +module_param_cb(poll, &poll_param_ops, &param_poll, 0444);
> core_initcall(cpuidle_init);

\
 
 \ /
  Last update: 2020-11-30 20:09    [W:0.105 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site