lkml.org 
[lkml]   [2020]   [Nov]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [RFC PATCH 2/3] RISC-V: Initial DTS for Microchip ICICLE board
On Tue, Nov 3, 2020 at 10:39 AM Ben Dooks <ben.dooks@codethink.co.uk> wrote:
>
> On 03/11/2020 18:36, Atish Patra wrote:
> > On Tue, Nov 3, 2020 at 10:28 AM Ben Dooks <ben.dooks@codethink.co.uk> wrote:
> >>
> >> On 03/11/2020 18:10, Cyril.Jean@microchip.com wrote:
> >>> On 11/3/20 3:07 PM, Atish Patra wrote:
> >>>> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> >>>>
> >>>> On Fri, Oct 30, 2020 at 2:20 PM Ben Dooks <ben.dooks@codethink.co.uk> wrote:
> >>
> >> ,snip[
> >>
> >>>>>> @Cyril : Can we enable both eMMC & sdcard at the same time ?
> >>>>> I would put /both/ in but only enable the one in use for the moment.
> >>>>> Our boards are booting of eMMC as supplied, so this isn't going to work
> >>>>> as well. The eMMC is 8bit wide, and thus is only delivering 11MB/sec
> >>>>> instead of 22MB/sec. This performance is still not great, but losing
> >>>>> half the data-rate is just not good.
> >>>>>
> >>>> I am not sure what should be enabled by default. Updating sdcard is much
> >>>> easier than eMMC card and we use that approach.
> >>>>
> >>>> @Cyril: Is there a way that we can enable both ?
> >>>>
> >>> Yes, we can enable both but this requires a modification to the FPGA
> >>> design. One of the guys prototyped this while I was away. We will move
> >>> this along. This will require reprogramming the FPGA with a new design
> >>> and HSS version.
> >>>
> >>> Regards,
> >>>
> >>> Cyril.
> >>
> >> I either missed or couldn't find a way of forcing the boot mode to be
> >> from the SD slot. Have I missed something? At the moment we'd like to
> >> have more storage available as the ~7G free on the eMMC is not enough.
> >>
> >
> > I use tftpboot to load the kernel & DT from the network. SD card is
> > enabled in this DT and Linux
> > kernel uses SD slot instead of eMMC.
> >
> > To summarize, eMMC is used for HSS & U-Boot while SD card is used for
> > Linux which makes
> > more storage available to Linux.
> >
> > IMO, we should enable the sdcard for Linux DT until updated FPGA
> > design & HSS is available.
>
> Interesting as for me the default is for Linux to use the eMMC as
> well. I can't see any way for forcing the selection lines in the
> DT to say eMMC vs SD.
>

because you are probably loading the DT passed by U-boot. I load the DTB
built from the Linux source (the one present in this patch) by
stopping the autoboot in U-Boot.

The DT in U-Boot disables the SD card.


> If there is a way of controlling the selection lines then it might
> be possible to have both cards enabled with a bus selection MUX in
> software.
>
>
> --
> Ben Dooks http://www.codethink.co.uk/
> Senior Engineer Codethink - Providing Genius
>
> https://www.codethink.co.uk/privacy.html



--
Regards,
Atish

\
 
 \ /
  Last update: 2020-11-03 19:46    [W:0.140 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site