lkml.org 
[lkml]   [2020]   [Nov]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2 1/1] arm64: dts: marvell: Add a device tree for the IEI Puzzle-M801 board
Date
Luka Kovacic <luka.kovacic@sartura.hr> writes:

> Add initial support for the IEI Puzzle-M801 1U Rackmount Network
> Appliance board.
>
> The board is based on the quad-core Marvell Armada 8040 SoC and supports
> up to 16 GB of DDR4 2400 MHz ECC RAM. It has a PCIe x16 slot (x2 lanes
> only) and an M.2 type B slot.
>
> Main system hardware:
> 2x USB 3.0
> 4x Gigabit Ethernet
> 2x SFP+
> 1x SATA 3.0
> 1x M.2 type B
> 1x RJ45 UART
> 1x SPI flash
> 1x IEI WT61P803 PUZZLE Microcontroller
> 1x EPSON RX8010 RTC (used instead of the integrated Marvell RTC controller)
> 6x SFP+ LED
> 1x HDD LED
>
> All of the hardware listed above is supported and tested in this port.
>
> Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
> Acked-by: Andrew Lunn <andrew@lunn.ch>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> Cc: Robert Marko <robert.marko@sartura.hr>

Applied on mvebu/dt64

Thanks,

Gregory
> ---
> Changes for v2:
> - Use the correct vendor title (IEI instead of iEi)
> - Sync the device tree with dt-bindings
>
> This patch is now sent separately from the IEI WT61P803 PUZZLE MCU
> patchset. Go to the following link for reference:
> https://lore.kernel.org/linux-hwmon/20201025005916.64747-1-luka.kovacic@sartura.hr/
>
> arch/arm64/boot/dts/marvell/Makefile | 1 +
> .../dts/marvell/armada-8040-puzzle-m801.dts | 523 ++++++++++++++++++
> 2 files changed, 524 insertions(+)
> create mode 100644 arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
>
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index 3e5f2e7a040c..e413c3261792 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-puzzle-m801.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
> new file mode 100644
> index 000000000000..dac85fa748de
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
> @@ -0,0 +1,523 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2016 Marvell Technology Group Ltd.
> + * Copyright (C) 2020 Sartura Ltd.
> + *
> + * Device Tree file for IEI Puzzle-M801
> + */
> +
> +#include "armada-8040.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> + model = "IEI-Puzzle-M801";
> + compatible = "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806";
> +
> + aliases {
> + ethernet0 = &cp0_eth0;
> + ethernet1 = &cp1_eth0;
> + ethernet2 = &cp0_eth1;
> + ethernet3 = &cp0_eth2;
> + ethernet4 = &cp1_eth1;
> + ethernet5 = &cp1_eth2;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + /* Regulator labels correspond with schematics */
> + v_3_3: regulator-3-3v {
> + compatible = "regulator-fixed";
> + regulator-name = "v_3_3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + status = "okay";
> + };
> +
> + v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_xhci_vbus_pins>;
> + regulator-name = "v_5v0_usb3_hst_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + status = "okay";
> + };
> +
> + v_vddo_h: regulator-1-8v {
> + compatible = "regulator-fixed";
> + regulator-name = "v_vddo_h";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + status = "okay";
> + };
> +
> + sfp_cp0_eth0: sfp-cp0-eth0 {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfpplus0_i2c>;
> + los-gpio = <&sfpplus_gpio 11 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpio = <&sfpplus_gpio 10 GPIO_ACTIVE_LOW>;
> + tx-disable-gpio = <&sfpplus_gpio 9 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpio = <&sfpplus_gpio 8 GPIO_ACTIVE_HIGH>;
> + maximum-power-milliwatt = <3000>;
> + };
> +
> + sfp_cp1_eth0: sfp-cp1-eth0 {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfpplus1_i2c>;
> + los-gpio = <&sfpplus_gpio 3 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpio = <&sfpplus_gpio 2 GPIO_ACTIVE_LOW>;
> + tx-disable-gpio = <&sfpplus_gpio 1 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpio = <&sfpplus_gpio 0 GPIO_ACTIVE_HIGH>;
> + maximum-power-milliwatt = <3000>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + status = "okay";
> + pinctrl-0 = <&cp0_sfpplus_led_pins &cp1_sfpplus_led_pins>;
> + pinctrl-names = "default";
> +
> + led-0 {
> + /* SFP+ port 2: Activity */
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <0>;
> + gpios = <&cp1_gpio1 6 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-1 {
> + /* SFP+ port 1: Activity */
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <1>;
> + gpios = <&cp1_gpio1 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-2 {
> + /* SFP+ port 2: 10 Gbps indicator */
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <2>;
> + gpios = <&cp1_gpio1 7 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-3 {
> + /* SFP+ port 2: 1 Gbps indicator */
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <3>;
> + gpios = <&cp1_gpio1 8 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-4 {
> + /* SFP+ port 1: 10 Gbps indicator */
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <4>;
> + gpios = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-5 {
> + /* SFP+ port 1: 1 Gbps indicator */
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <5>;
> + gpios = <&cp1_gpio1 31 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-6 {
> + function = LED_FUNCTION_DISK;
> + linux,default-trigger = "disk-activity";
> + gpios = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>;
> + };
> +
> + };
> +};
> +
> +&ap_sdhci0 {
> + bus-width = <8>;
> + /*
> + * Not stable in HS modes - phy needs "more calibration", so add
> + * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes.
> + */
> + marvell,xenon-phy-slow-mode;
> + no-1-8-v;
> + no-sd;
> + no-sdio;
> + non-removable;
> + status = "okay";
> + vqmmc-supply = <&v_vddo_h>;
> +};
> +
> +&ap_thermal_cpu1 {
> + trips {
> + cpu_active: cpu-active {
> + temperature = <44000>;
> + hysteresis = <2000>;
> + type = "active";
> + };
> + };
> + cooling-maps {
> + fan-map {
> + trip = <&cpu_active>;
> + cooling-device = <&chassis_fan_group0 64 THERMAL_NO_LIMIT>,
> + <&chassis_fan_group1 64 THERMAL_NO_LIMIT>;
> + };
> + };
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + rtc@32 {
> + compatible = "epson,rx8010";
> + reg = <0x32>;
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> + spi-flash@0 {
> + #address-cells = <0x1>;
> + #size-cells = <0x1>;
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-max-frequency = <20000000>;
> + partition@u-boot {
> + label = "u-boot";
> + reg = <0x00000000 0x001f0000>;
> + };
> + partition@u-boot-env {
> + label = "u-boot-env";
> + reg = <0x001f0000 0x00010000>;
> + };
> + partition@ubi1 {
> + label = "ubi1";
> + reg = <0x00200000 0x03f00000>;
> + };
> + partition@ubi2 {
> + label = "ubi2";
> + reg = <0x04100000 0x03f00000>;
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> + pinctrl-0 = <&uart0_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&uart1 {
> + status = "okay";
> + /* IEI WT61P803 PUZZLE MCU Controller */
> + mcu {
> + compatible = "iei,wt61p803-puzzle";
> + current-speed = <115200>;
> + enable-beep;
> +
> + leds {
> + compatible = "iei,wt61p803-puzzle-leds";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + led@0 {
> + reg = <0>;
> + function = LED_FUNCTION_POWER;
> + color = <LED_COLOR_ID_BLUE>;
> + };
> + };
> +
> + hwmon {
> + compatible = "iei,wt61p803-puzzle-hwmon";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + chassis_fan_group0:fan-group@0 {
> + #cooling-cells = <2>;
> + reg = <0x00>;
> + cooling-levels = <64 102 170 230 250>;
> + };
> +
> + chassis_fan_group1:fan-group@1 {
> + #cooling-cells = <2>;
> + reg = <0x01>;
> + cooling-levels = <64 102 170 230 250>;
> + };
> + };
> + };
> +};
> +
> +&cp0_rtc {
> + status = "disabled";
> +};
> +
> +&cp0_i2c0 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_i2c0_pins>;
> + status = "okay";
> +
> + sfpplus_gpio: gpio@21 {
> + compatible = "nxp,pca9555";
> + reg = <0x21>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + eeprom@54 {
> + compatible = "atmel,24c04";
> + reg = <0x54>;
> + };
> +};
> +
> +&cp0_i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_i2c1_pins>;
> + status = "okay";
> +
> + i2c-switch@70 {
> + compatible = "nxp,pca9544";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> +
> + sfpplus0_i2c: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + sfpplus1_i2c: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> + };
> +};
> +
> +&cp0_uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_uart1_pins>;
> + status = "okay";
> +};
> +
> +&cp0_mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + status = "okay";
> +
> + ge_phy2: ethernet-phy@0 {
> + reg = <0>;
> + };
> +
> + ge_phy3: ethernet-phy@1 {
> + reg = <1>;
> + };
> +};
> +
> +&cp0_pcie0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_pcie_pins>;
> + num-lanes = <1>;
> + num-viewport = <8>;
> + reset-gpios = <&cp0_gpio2 20 GPIO_ACTIVE_LOW>;
> + ranges = <0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
> + phys = <&cp0_comphy0 0>;
> + phy-names = "cp0-pcie0-x1-phy";
> + status = "okay";
> +};
> +
> +&cp0_pinctrl {
> + cp0_ge_mdio_pins: ge-mdio-pins {
> + marvell,pins = "mpp32", "mpp34";
> + marvell,function = "ge";
> + };
> + cp0_i2c1_pins: i2c1-pins {
> + marvell,pins = "mpp35", "mpp36";
> + marvell,function = "i2c1";
> + };
> + cp0_i2c0_pins: i2c0-pins {
> + marvell,pins = "mpp37", "mpp38";
> + marvell,function = "i2c0";
> + };
> + cp0_uart1_pins: uart1-pins {
> + marvell,pins = "mpp40", "mpp41";
> + marvell,function = "uart1";
> + };
> + cp0_xhci_vbus_pins: xhci0-vbus-pins {
> + marvell,pins = "mpp47";
> + marvell,function = "gpio";
> + };
> + cp0_pcie_pins: pcie-pins {
> + marvell,pins = "mpp52";
> + marvell,function = "gpio";
> + };
> + cp0_sdhci_pins: sdhci-pins {
> + marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59",
> + "mpp60", "mpp61";
> + marvell,function = "sdio";
> + };
> + cp0_sfpplus_led_pins: sfpplus-led-pins {
> + marvell,pins = "mpp54";
> + marvell,function = "gpio";
> + };
> +};
> +
> +&cp0_ethernet {
> + status = "okay";
> +};
> +
> +&cp0_eth0 {
> + status = "okay";
> + phy-mode = "10gbase-r";
> + phys = <&cp0_comphy4 0>;
> + local-mac-address = [ae 00 00 00 ff 00];
> + sfp = <&sfp_cp0_eth0>;
> + managed = "in-band-status";
> +};
> +
> +&cp0_eth1 {
> + status = "okay";
> + phy = <&ge_phy2>;
> + phy-mode = "sgmii";
> + local-mac-address = [ae 00 00 00 ff 01];
> + phys = <&cp0_comphy3 1>;
> +};
> +
> +&cp0_eth2 {
> + status = "okay";
> + phy-mode = "sgmii";
> + phys = <&cp0_comphy1 2>;
> + local-mac-address = [ae 00 00 00 ff 02];
> + phy = <&ge_phy3>;
> +};
> +
> +&cp0_sata0 {
> + status = "okay";
> +
> + sata-port@0 {
> + phys = <&cp0_comphy2 0>;
> + phy-names = "cp0-sata0-0-phy";
> + };
> +
> + sata-port@1 {
> + phys = <&cp0_comphy5 1>;
> + phy-names = "cp0-sata0-1-phy";
> + };
> +};
> +
> +&cp0_sdhci0 {
> + broken-cd;
> + bus-width = <4>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_sdhci_pins>;
> + status = "okay";
> + vqmmc-supply = <&v_3_3>;
> +};
> +
> +&cp0_usb3_0 {
> + status = "okay";
> +};
> +
> +&cp0_usb3_1 {
> + status = "okay";
> +};
> +
> +&cp1_i2c0 {
> + clock-frequency = <100000>;
> + status = "disabled";
> +};
> +
> +&cp1_i2c1 {
> + clock-frequency = <100000>;
> + status = "disabled";
> +};
> +
> +&cp1_rtc {
> + status = "disabled";
> +};
> +
> +&cp1_ethernet {
> + status = "okay";
> +};
> +
> +&cp1_eth0 {
> + status = "okay";
> + phy-mode = "10gbase-r";
> + phys = <&cp1_comphy4 0>;
> + local-mac-address = [ae 00 00 00 ff 03];
> + sfp = <&sfp_cp1_eth0>;
> + managed = "in-band-status";
> +};
> +
> +&cp1_eth1 {
> + status = "okay";
> + phy = <&ge_phy4>;
> + phy-mode = "sgmii";
> + local-mac-address = [ae 00 00 00 ff 04];
> + phys = <&cp1_comphy3 1>;
> +};
> +
> +&cp1_eth2 {
> + status = "okay";
> + phy-mode = "sgmii";
> + local-mac-address = [ae 00 00 00 ff 05];
> + phys = <&cp1_comphy5 2>;
> + phy = <&ge_phy5>;
> +};
> +
> +&cp1_pinctrl {
> + cp1_sfpplus_led_pins: sfpplus-led-pins {
> + marvell,pins = "mpp6", "mpp7", "mpp8", "mpp10", "mpp14", "mpp31";
> + marvell,function = "gpio";
> + };
> +};
> +
> +&cp1_uart0 {
> + status = "disabled";
> +};
> +
> +&cp1_comphy2 {
> + cp1_usbh0_con: connector {
> + compatible = "usb-a-connector";
> + phy-supply = <&v_5v0_usb3_hst_vbus>;
> + };
> +};
> +
> +&cp1_usb3_0 {
> + phys = <&cp1_comphy2 0>;
> + phy-names = "cp1-usb3h0-comphy";
> + status = "okay";
> +};
> +
> +&cp1_mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + status = "okay";
> +
> + ge_phy4: ethernet-phy@1 {
> + reg = <1>;
> + };
> + ge_phy5: ethernet-phy@0 {
> + reg = <0>;
> + };
> +};
> +
> +&cp1_pcie0 {
> + num-lanes = <2>;
> + phys = <&cp1_comphy0 0>, <&cp1_comphy1 0>;
> + phy-names = "cp1-pcie0-x2-lane0-phy", "cp1-pcie0-x2-lane1-phy";
> + status = "okay";
> +};
> --
> 2.26.2
>

--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com

\
 
 \ /
  Last update: 2020-11-29 12:08    [W:0.155 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site