lkml.org 
[lkml]   [2020]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] net: phy: fix auto-negotiation in case of 'down-shift'
From
Date
Am 24.11.2020 um 16:17 schrieb Antonio Borneo:
> On Tue, 2020-11-24 at 14:56 +0000, Russell King - ARM Linux admin wrote:
>> On Tue, Nov 24, 2020 at 03:38:48PM +0100, Antonio Borneo wrote:
>>> If the auto-negotiation fails to establish a gigabit link, the phy
>>> can try to 'down-shift': it resets the bits in MII_CTRL1000 to
>>> stop advertising 1Gbps and retries the negotiation at 100Mbps.
>>>
>>> From commit 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode
>>> in genphy_read_status") the content of MII_CTRL1000 is not checked
>>> anymore at the end of the negotiation, preventing the detection of
>>> phy 'down-shift'.
>>> In case of 'down-shift' phydev->advertising gets out-of-sync wrt
>>> MII_CTRL1000 and still includes modes that the phy have already
>>> dropped. The link partner could still advertise higher speeds,
>>> while the link is established at one of the common lower speeds.
>>> The logic 'and' in phy_resolve_aneg_linkmode() between
>>> phydev->advertising and phydev->lp_advertising will report an
>>> incorrect mode.
>>>
>>> Issue detected with a local phy rtl8211f connected with a gigabit
>>> capable router through a two-pairs network cable.
>>>
>>> After auto-negotiation, read back MII_CTRL1000 and mask-out from
>>> phydev->advertising the modes that have been eventually discarded
>>> due to the 'down-shift'.
>>
>> Sorry, but no. While your solution will appear to work, in
>> introduces unexpected changes to the user visible APIs.
>>
>>>   if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) {
>>> + if (phydev->is_gigabit_capable) {
>>> + adv = phy_read(phydev, MII_CTRL1000);
>>> + if (adv < 0)
>>> + return adv;
>>> + /* update advertising in case of 'down-shift' */
>>> + mii_ctrl1000_mod_linkmode_adv_t(phydev->advertising,
>>> + adv);
>>
>> If a down-shift occurs, this will cause the configured advertising
>> mask to lose the 1G speed, which will be visible to userspace.
>
> You are right, it gets propagated to user that 1Gbps is not advertised
>
>> Userspace doesn't expect the advertising mask to change beneath it.
>> Since updates from userspace are done using a read-modify-write of
>> the ksettings, this can have the undesired effect of removing 1G
>> from the configured advertising mask.
>>
>> We've had other PHYs have this behaviour; the correct solution is for
>> the PHY driver to implement reading the resolution from the PHY rather
>> than relying on the generic implementation if it can down-shift
>
> If it's already upstream, could you please point to one of the phy driver
> that already implements this properly?
>

See e.g. aqr107_read_rate(), used by aqr107_read_status().

> Thanks
> Antonio
>

\
 
 \ /
  Last update: 2020-11-24 16:27    [W:0.351 / U:0.240 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site