lkml.org 
[lkml]   [2020]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/3] spi: convert to BIT() all spi_device flags
Date
This change converts all bit flags for the 'struct spi_device' mode to the
BIT() macro. The change is mostly for readability. Since adding more bit
fields, might as well convert it now.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
---

Changelog v1 -> v2:
* https://lore.kernel.org/linux-spi/20201111141529.98147-1-alexandru.ardelean@analog.com/
* add patch 'spi: convert to BIT() all spi_device flags'
* for patch 'spi: Add SPI_NO_TX/RX support'
convert comment to new multi-line format
* add patch 'spi: dt-bindings: document zero value for spi-{rx,tx}-bus-width properties'

include/linux/spi/spi.h | 32 ++++++++++++++++----------------
1 file changed, 16 insertions(+), 16 deletions(-)

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index aa09fdc8042d..66c7d8e45563 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -165,27 +165,27 @@ struct spi_device {
u8 bits_per_word;
bool rt;
u32 mode;
-#define SPI_CPHA 0x01 /* clock phase */
-#define SPI_CPOL 0x02 /* clock polarity */
+#define SPI_CPHA BIT(0) /* clock phase */
+#define SPI_CPOL BIT(1) /* clock polarity */
#define SPI_MODE_0 (0|0) /* (original MicroWire) */
#define SPI_MODE_1 (0|SPI_CPHA)
#define SPI_MODE_2 (SPI_CPOL|0)
#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA)
#define SPI_MODE_X_MASK (SPI_CPOL|SPI_CPHA)
-#define SPI_CS_HIGH 0x04 /* chipselect active high? */
-#define SPI_LSB_FIRST 0x08 /* per-word bits-on-wire */
-#define SPI_3WIRE 0x10 /* SI/SO signals shared */
-#define SPI_LOOP 0x20 /* loopback mode */
-#define SPI_NO_CS 0x40 /* 1 dev/bus, no chipselect */
-#define SPI_READY 0x80 /* slave pulls low to pause */
-#define SPI_TX_DUAL 0x100 /* transmit with 2 wires */
-#define SPI_TX_QUAD 0x200 /* transmit with 4 wires */
-#define SPI_RX_DUAL 0x400 /* receive with 2 wires */
-#define SPI_RX_QUAD 0x800 /* receive with 4 wires */
-#define SPI_CS_WORD 0x1000 /* toggle cs after each word */
-#define SPI_TX_OCTAL 0x2000 /* transmit with 8 wires */
-#define SPI_RX_OCTAL 0x4000 /* receive with 8 wires */
-#define SPI_3WIRE_HIZ 0x8000 /* high impedance turnaround */
+#define SPI_CS_HIGH BIT(2) /* chipselect active high? */
+#define SPI_LSB_FIRST BIT(3) /* per-word bits-on-wire */
+#define SPI_3WIRE BIT(4) /* SI/SO signals shared */
+#define SPI_LOOP BIT(5) /* loopback mode */
+#define SPI_NO_CS BIT(6) /* 1 dev/bus, no chipselect */
+#define SPI_READY BIT(7) /* slave pulls low to pause */
+#define SPI_TX_DUAL BIT(8) /* transmit with 2 wires */
+#define SPI_TX_QUAD BIT(9) /* transmit with 4 wires */
+#define SPI_RX_DUAL BIT(10) /* receive with 2 wires */
+#define SPI_RX_QUAD BIT(11) /* receive with 4 wires */
+#define SPI_CS_WORD BIT(12) /* toggle cs after each word */
+#define SPI_TX_OCTAL BIT(13) /* transmit with 8 wires */
+#define SPI_RX_OCTAL BIT(14) /* receive with 8 wires */
+#define SPI_3WIRE_HIZ BIT(15) /* high impedance turnaround */
int irq;
void *controller_state;
void *controller_data;
--
2.17.1
\
 
 \ /
  Last update: 2020-11-24 11:17    [W:0.047 / U:0.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site