lkml.org 
[lkml]   [2020]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [PATCH] ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Add OV7725 nodes
Hi Prabhakar,

On Fri, Nov 20, 2020 at 4:13 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> Add the ov7725 endpoint nodes to the camera daughter board. The ov7725
> sensors can be populated on I2C{0,1,2,3} buses.
>
> By default the VIN{0,1,2,3} are tied to OV5640{0,1,2,3} endpoints
> respectively in the camera DB dts hence the remote-endpoint property in
> OV7725{0,1,2,3} endpoints is commented out.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>

Thanks for your patch!

The camera definitions look mostly OK to me.

IIUIC, these are 4 plug-in cameras, that can be used instead of the
(currently described) 4 other OV5640-based plug-in cameras?
In addition, the user can mix and match them, in the 4 available
slots (J11-J14), which would require editing the DTS?

Wouldn't it be easier to have separate DTS files for the OV7725 and
OV5640 cameras, and #include them from r8a7742-iwg21d-q7-dbcm-ca.dts?

/* 8bit CMOS Camera 1 (J13) */
#define MCLK_CAM &mclk_cam1
#define ...
/* Comment the below according to connected cameras */
#include "ov5640.dts"
//#include "ov7725.dts"
#undef MCLK_CAM
#undef ...

[...]

> --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts

> @@ -152,6 +198,30 @@
> };
> };
> };
> +
> + ov7725@21 {
> + status = "disabled";

This one is disabled, the three others aren't?

> + compatible = "ovti,ov7725";
> + reg = <0x21>;
> + clocks = <&mclk_cam3>;
> +
> + port {
> + ov7725_2: endpoint {
> + bus-width = <8>;
> + bus-type = <6>;
> + /*
> + * uncomment remote-endpoint property to
> + * tie ov7725_2 to vin2ep also make
> + * sure to comment/remove remote-endpoint
> + * property from ov5640_2 endpoint and
> + * replace remote-endpoint property in
> + * vin2ep node with
> + * remote-endpoint = <&ov7725_2>;
> + */
> + /* remote-endpoint = <&vin2ep>; */
> + };
> + };
> + };
> };

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

\
 
 \ /
  Last update: 2020-11-24 10:06    [W:0.395 / U:0.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site