lkml.org 
[lkml]   [2020]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] char: tpm: add i2c driver for cr50
On Fri, Nov 20, 2020 at 07:23:45PM +0200, Adrian Ratiu wrote:
> From: "dlaurie@chromium.org" <dlaurie@chromium.org>
>
> Add TPM 2.0 compatible I2C interface for chips with cr50 firmware.
>
> The firmware running on the currently supported H1 MCU requires a
> special driver to handle its specific protocol, and this makes it
> unsuitable to use tpm_tis_core_* and instead it must implement the
> underlying TPM protocol similar to the other I2C TPM drivers.
>
> - All 4 byes of status register must be read/written at once.
> - FIFO and burst count is limited to 63 and must be drained by AP.
> - Provides an interrupt to indicate when read response data is ready
> and when the TPM is finished processing write data.
>
> This driver is based on the existing infineon I2C TPM driver, which
> most closely matches the cr50 i2c protocol behavior.
>
> Cc: Helen Koike <helen.koike@collabora.com>
> Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
> [swboyd@chromium.org: Depend on i2c even if it's a module, replace
> boilier plate with SPDX tag, drop asm/byteorder.h include, simplify
> return from probe]
> Signed-off-by: Stephen Boyd <swboyd@chromium.org>
> Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
> Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
> ---
> Changes in v2:
> - Various small fixes all over (reorder includes, MAX_BUFSIZE, comments, etc)
> - Reworked return values of i2c_wait_tpm_ready() to fix timeout mis-handling
> so ret == 0 now means success, the wait period jiffies is ignored because that
> number is meaningless and return a proper timeout error in case jiffies == 0.
> - Make i2c default to 1 message per transfer (requested by Helen)
> - Move -EIO error reporting to transfer function to cleanup transfer() itself
> and its R/W callers
> - Remove magic value hardcodings and introduce enum force_release.
>
> v1 posted at https://lkml.org/lkml/2020/2/25/349
>
> Applies on next-20201120, tested on Chromebook EVE.
> ---
> drivers/char/tpm/Kconfig | 10 +
> drivers/char/tpm/Makefile | 2 +
> drivers/char/tpm/tpm_tis_i2c_cr50.c | 768 ++++++++++++++++++++++++++++
> 3 files changed, 780 insertions(+)
> create mode 100644 drivers/char/tpm/tpm_tis_i2c_cr50.c
>
> diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig
> index a18c314da211..4308f9ca7a43 100644
> --- a/drivers/char/tpm/Kconfig
> +++ b/drivers/char/tpm/Kconfig
> @@ -86,6 +86,16 @@ config TCG_TIS_SYNQUACER
> To compile this driver as a module, choose M here;
> the module will be called tpm_tis_synquacer.
>
> +config TCG_TIS_I2C_CR50
> + tristate "TPM Interface Specification 2.0 Interface (I2C - CR50)"
> + depends on I2C
> + select TCG_CR50
> + help
> + This is a driver for the Google cr50 I2C TPM interface which is a
> + custom microcontroller and requires a custom i2c protocol interface
> + to handle the limitations of the hardware. To compile this driver
> + as a module, choose M here; the module will be called tcg_tis_i2c_cr50.
> +
> config TCG_TIS_I2C_ATMEL
> tristate "TPM Interface Specification 1.2 Interface (I2C - Atmel)"
> depends on I2C
> diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile
> index 84db4fb3a9c9..66d39ea6bd10 100644
> --- a/drivers/char/tpm/Makefile
> +++ b/drivers/char/tpm/Makefile
> @@ -27,6 +27,8 @@ obj-$(CONFIG_TCG_TIS_SPI) += tpm_tis_spi.o
> tpm_tis_spi-y := tpm_tis_spi_main.o
> tpm_tis_spi-$(CONFIG_TCG_TIS_SPI_CR50) += tpm_tis_spi_cr50.o
>
> +obj-$(CONFIG_TCG_TIS_I2C_CR50) += tpm_tis_i2c_cr50.o
> +
> obj-$(CONFIG_TCG_TIS_I2C_ATMEL) += tpm_i2c_atmel.o
> obj-$(CONFIG_TCG_TIS_I2C_INFINEON) += tpm_i2c_infineon.o
> obj-$(CONFIG_TCG_TIS_I2C_NUVOTON) += tpm_i2c_nuvoton.o
> diff --git a/drivers/char/tpm/tpm_tis_i2c_cr50.c b/drivers/char/tpm/tpm_tis_i2c_cr50.c
> new file mode 100644
> index 000000000000..37555dafdca0
> --- /dev/null
> +++ b/drivers/char/tpm/tpm_tis_i2c_cr50.c
> @@ -0,0 +1,768 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright 2016 Google Inc.
> + *
> + * Based on Linux Kernel TPM driver by
> + * Peter Huewe <peter.huewe@infineon.com>
> + * Copyright (C) 2011 Infineon Technologies
> + */
> +
> +/*
> + * cr50 is a firmware for H1 secure modules that requires special
> + * handling for the I2C interface.
> + *
> + * - Use an interrupt for transaction status instead of hardcoded delays
> + * - Must use write+wait+read read protocol
> + * - All 4 bytes of status register must be read/written at once
> + * - Burst count max is 63 bytes, and burst count behaves
> + * slightly differently than other I2C TPMs
> + * - When reading from FIFO the full burstcnt must be read
> + * instead of just reading header and determining the remainder
> + */
> +
> +#include <linux/acpi.h>
> +#include <linux/completion.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/pm.h>
> +#include <linux/slab.h>
> +#include <linux/wait.h>
> +
> +#include "tpm_tis_core.h"
> +
> +#define CR50_MAX_BUFSIZE 64
> +#define CR50_TIMEOUT_SHORT_MS 2 /* Short timeout during transactions */
> +#define CR50_TIMEOUT_NOIRQ_MS 20 /* Timeout for TPM ready without IRQ */
> +#define CR50_I2C_DID_VID 0x00281ae0L
> +#define CR50_I2C_MAX_RETRIES 3 /* Max retries due to I2C errors */
> +#define CR50_I2C_RETRY_DELAY_LO 55 /* Min usecs between retries on I2C */
> +#define CR50_I2C_RETRY_DELAY_HI 65 /* Max usecs between retries on I2C */

CR50_ -> TPM_CR50_

> +
> +#define TPM_I2C_ACCESS(l) (0x0000 | ((l) << 4))
> +#define TPM_I2C_STS(l) (0x0001 | ((l) << 4))
> +#define TPM_I2C_DATA_FIFO(l) (0x0005 | ((l) << 4))
> +#define TPM_I2C_DID_VID(l) (0x0006 | ((l) << 4))
> +
> +struct priv_data {
> + int irq;
> + int locality;
> + struct completion tpm_ready;
> + u8 buf[CR50_MAX_BUFSIZE];
> +};

tpm_i2c_cr50_priv_data

> +
> +enum force_release {
> + CR50_NO_FORCE = 0x0,
> + CR50_FORCE = 0x1,
> +};

I'd just

#define TPM_I2C_CR50_NO_FORCE 0
#define TPM_I2C_CR50_FORCE 1

> +
> +/*
> + * The cr50 interrupt handler just signals waiting threads that the
> + * interrupt was asserted. It does not do any processing triggered
> + * by interrupts but is instead used to avoid fixed delays.
> + *
> + * @dummy: unuesed parameter
> + * @dev_id: TPM chip information
> + */

Please review for kdoc:

https://www.kernel.org/doc/Documentation/kernel-doc-nano-HOWTO.txt

> +static irqreturn_t cr50_i2c_int_handler(int dummy, void *dev_id)

cr50 -> tpm_i2c_cr50_

> +{
> + struct tpm_chip *chip = dev_id;
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> +
> + complete(&priv->tpm_ready);
> +
> + return IRQ_HANDLED;
> +}
> +
> +/*
> + * Wait for completion interrupt if available, otherwise use a fixed
> + * delay for the TPM to be ready.
> + *
> + * @chip: TPM chip information
> + *
> + * Returns 0 for success, negative number for timeout
> + */
> +static int cr50_i2c_wait_tpm_ready(struct tpm_chip *chip)

Ditto.

> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> +
> + /* Use a safe fixed delay if interrupt is not supported */
> + if (priv->irq <= 0) {
> + msleep(CR50_TIMEOUT_NOIRQ_MS);
> + return 0;
> + }
> +
> + /* Wait for interrupt to indicate TPM is ready to respond */
> + if (!wait_for_completion_timeout(&priv->tpm_ready,
> + msecs_to_jiffies(chip->timeout_a))) {
> + dev_warn(&chip->dev, "Timeout waiting for TPM ready\n");
> + return -ETIMEDOUT;
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * cr50_i2c_enable_tpm_irq - enable TPM irq
> + *
> + * @chip: TPM chip information
> + */
> +static void cr50_i2c_enable_tpm_irq(struct tpm_chip *chip)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> +
> + if (priv->irq > 0) {
> + reinit_completion(&priv->tpm_ready);
> + enable_irq(priv->irq);
> + }
> +}
> +
> +/*
> + * cr50_i2c_disable_tpm_irq - disable TPM irq
> + *
> + * @chip: TPM chip information
> + */
> +static void cr50_i2c_disable_tpm_irq(struct tpm_chip *chip)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> +
> + if (priv->irq > 0)
> + disable_irq(priv->irq);
> +}
> +
> +/*
> + * cr50_i2c_transfer_message - transfer a message over i2c
> + *
> + * @dev: device information
> + * @adapter: i2c adapter
> + * @msg: message to transfer
> + *
> + * Call unlocked i2c transfer routine with the provided parameters and retry
> + * in case of bus errors. Returns 0 on success, otherwise negative errno.
> + */
> +static int cr50_i2c_transfer_message(struct device *dev,
> + struct i2c_adapter *adapter,
> + struct i2c_msg *msg)
> +{
> + int rc = 0;
> + unsigned int try;
> +
> + for (try = 0; try < CR50_I2C_MAX_RETRIES; try++) {
> + rc = __i2c_transfer(adapter, msg, 1);
> + if (rc == 1)
> + return 0; /* Successfully transferred the message */
> + if (try)
> + dev_warn(dev, "i2c transfer failed (attempt %d/%d): %d\n",
> + try + 1, CR50_I2C_MAX_RETRIES, rc);
> + usleep_range(CR50_I2C_RETRY_DELAY_LO, CR50_I2C_RETRY_DELAY_HI);
> + }
> +
> + return -EIO; /* No i2c message transferred */
> +}
> +
> +/*
> + * cr50_i2c_read() - read from TPM register
> + *

Not only wrong formatting but seems that these kdoc's have differing
formatting (no newline).

> + * @chip: TPM chip information
> + * @addr: register address to read from
> + * @buffer: provided by caller
> + * @len: number of bytes to read
> + *
> + * 1) send register address byte 'addr' to the TPM
> + * 2) wait for TPM to indicate it is ready
> + * 3) read 'len' bytes of TPM response into the provided 'buffer'

Please write proper sentences instead of lower-case (also applies
to parameters as you can see from kernel documentation).

> + *
> + * Returns negative number for error, 0 for success.
> + */
> +static int cr50_i2c_read(struct tpm_chip *chip, u8 addr, u8 *buffer, size_t len)
> +{
> + struct i2c_client *client = to_i2c_client(chip->dev.parent);
> + struct i2c_msg msg1 = {
> + .addr = client->addr,
> + .len = 1,
> + .buf = &addr
> + };
> + struct i2c_msg msg2 = {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = len,
> + .buf = buffer
> + };
> + int rc;
> +
> + i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT);
> +
> + /* Prepare for completion interrupt */
> + cr50_i2c_enable_tpm_irq(chip);
> +
> + /* Send the register address byte to the TPM */
> + rc = cr50_i2c_transfer_message(&chip->dev, client->adapter, &msg1);
> + if (rc < 0)
> + goto out;
> +
> + /* Wait for TPM to be ready with response data */
> + rc = cr50_i2c_wait_tpm_ready(chip);
> + if (rc < 0)
> + goto out;
> +
> + /* Read response data from the TPM */
> + rc = cr50_i2c_transfer_message(&chip->dev, client->adapter, &msg2);
> +
> +out:
> + cr50_i2c_disable_tpm_irq(chip);
> + i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT);
> +
> + if (rc < 0)
> + return rc;
> +
> + return 0;
> +}
> +
> +/*
> + * cr50_i2c_write() - write to TPM register
> + *
> + * @chip: TPM chip information
> + * @addr: register address to write to
> + * @buffer: data to write
> + * @len: number of bytes to write
> + *
> + * 1) prepend the provided address to the provided data
> + * 2) send the address+data to the TPM
> + * 3) wait for TPM to indicate it is done writing
> + *
> + * Returns negative number for error, 0 for success.
> + */
> +static int cr50_i2c_write(struct tpm_chip *chip, u8 addr, u8 *buffer,
> + size_t len)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + struct i2c_client *client = to_i2c_client(chip->dev.parent);
> + struct i2c_msg msg1 = {
> + .addr = client->addr,
> + .len = len + 1,
> + .buf = priv->buf
> + };
> + int rc;
> +
> + if (len > CR50_MAX_BUFSIZE - 1)
> + return -EINVAL;
> +
> + i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT);
> +
> + /* Prepend the 'register address' to the buffer */
> + priv->buf[0] = addr;
> + memcpy(priv->buf + 1, buffer, len);
> +
> + /* Prepare for completion interrupt */
> + cr50_i2c_enable_tpm_irq(chip);
> +
> + /* Send write request buffer with address */
> + rc = cr50_i2c_transfer_message(&chip->dev, client->adapter, &msg1);
> + if (rc < 0)
> + goto out;
> +
> + /* Wait for TPM to be ready, ignore timeout */
> + cr50_i2c_wait_tpm_ready(chip);
> +
> +out:
> + cr50_i2c_disable_tpm_irq(chip);
> + i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT);
> +
> + if (rc < 0)
> + return rc;
> +
> + return 0;
> +}
> +
> +/*
> + * cr50_check_locality - verify TPM locality
> + *
> + * @chip: TPM chip information
> + *
> + * Returns negative number for error, 0 for success.
> + */
> +static int cr50_check_locality(struct tpm_chip *chip)
> +{
> + u8 mask = TPM_ACCESS_VALID | TPM_ACCESS_ACTIVE_LOCALITY;
> + u8 buf;
> + int rc;
> +
> + rc = cr50_i2c_read(chip, TPM_I2C_ACCESS(0), &buf, sizeof(buf));
> + if (rc < 0)
> + return rc;
> +
> + if ((buf & mask) == mask)
> + return 0;
> +
> + return -EIO;
> +}
> +
> +/*
> + * cr50_release_locality - release TPM locality
> + *
> + * @chip: TPM chip information
> + * @force: flag to force release if set
> + */
> +static void cr50_release_locality(struct tpm_chip *chip,
> + enum force_release force)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + u8 mask = TPM_ACCESS_VALID | TPM_ACCESS_REQUEST_PENDING;
> + u8 addr = TPM_I2C_ACCESS(priv->locality);
> + u8 buf;
> +
> + if (cr50_i2c_read(chip, addr, &buf, sizeof(buf)) < 0)
> + return;
> +
> + if (force || (buf & mask) == mask) {
> + buf = TPM_ACCESS_ACTIVE_LOCALITY;
> + cr50_i2c_write(chip, addr, &buf, sizeof(buf));
> + }
> +
> + priv->locality = 0;
> +}
> +
> +/*
> + * request_locality - request TPM locality
> + *
> + * @chip: TPM chip information
> + */
> +static int request_locality(struct tpm_chip *chip)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + u8 buf = TPM_ACCESS_REQUEST_USE;
> + unsigned long stop;
> + int rc;
> +
> + if (!cr50_check_locality(chip))
> + return 0;
> +
> + rc = cr50_i2c_write(chip, TPM_I2C_ACCESS(0), &buf, sizeof(buf));
> + if (rc < 0)
> + return rc;
> +
> + stop = jiffies + chip->timeout_a;
> + do {
> + if (!cr50_check_locality(chip)) {
> + priv->locality = 0;
> + return 0;
> + }
> + msleep(CR50_TIMEOUT_SHORT_MS);
> + } while (time_before(jiffies, stop));
> +
> + return -ETIMEDOUT;
> +}
> +
> +/*
> + * cr50 requires all 4 bytes of status register to be read
> + *
> + * @chip: TPM chip information
> + *
> + * Returns TPM status
> + */
> +static u8 cr50_i2c_tis_status(struct tpm_chip *chip)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + u8 buf[4];
> +
> + if (cr50_i2c_read(chip, TPM_I2C_STS(priv->locality),
> + buf, sizeof(buf)) < 0)
> + return 0;
> + return buf[0];
> +}
> +
> +/*
> + * cr50 requires all 4 bytes of status register to be written
> + *
> + * @chip: TPM chip information
> + */
> +static void cr50_i2c_tis_ready(struct tpm_chip *chip)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + u8 buf[4] = { TPM_STS_COMMAND_READY };
> +
> + cr50_i2c_write(chip, TPM_I2C_STS(priv->locality), buf, sizeof(buf));
> + msleep(CR50_TIMEOUT_SHORT_MS);
> +}
> +
> +/*
> + * cr50 uses bytes 3:2 of status register for burst count and
> + * all 4 bytes must be read
> + *
> + * @chip: TPM chip information
> + * @mask: status mask
> + * @burst: return value for burst
> + * @status: return value for statis
> + *
> + * Returns negative number for error, 0 for success.
> + */
> +static int cr50_i2c_wait_burststs(struct tpm_chip *chip, u8 mask,
> + size_t *burst, int *status)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + unsigned long stop;
> + u8 buf[4];
> +
> + /* wait for burstcount */
> + stop = jiffies + chip->timeout_b;
> + do {
> + if (cr50_i2c_read(chip, TPM_I2C_STS(priv->locality),
> + buf, sizeof(buf)) < 0) {
> + msleep(CR50_TIMEOUT_SHORT_MS);
> + continue;
> + }
> +
> + *status = *buf;
> + *burst = le16_to_cpup((__le16 *)(buf + 1));
> +
> + if ((*status & mask) == mask &&
> + *burst > 0 && *burst <= CR50_MAX_BUFSIZE - 1)
> + return 0;
> +
> + msleep(CR50_TIMEOUT_SHORT_MS);
> + } while (time_before(jiffies, stop));
> +
> + dev_err(&chip->dev, "Timeout reading burst and status\n");
> + return -ETIMEDOUT;
> +}
> +
> +/*
> + * cr50_i2c_tis_recv - TPM reception callback
> + *
> + * @chip: TPM chip information
> + * @buf: reception buffer
> + * @buf_len: buffer length to read
> + *
> + * Returns negative number for error, number of bytes read for success.
> + */
> +static int cr50_i2c_tis_recv(struct tpm_chip *chip, u8 *buf, size_t buf_len)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + int status, rc;
> + size_t burstcnt, cur, len, expected;
> + u8 addr = TPM_I2C_DATA_FIFO(priv->locality);
> + u8 mask = TPM_STS_VALID | TPM_STS_DATA_AVAIL;
> +
> + if (buf_len < TPM_HEADER_SIZE)
> + return -EINVAL;
> +
> + rc = cr50_i2c_wait_burststs(chip, mask, &burstcnt, &status);
> + if (rc < 0)
> + goto out_err;
> +
> + if (burstcnt > buf_len || burstcnt < TPM_HEADER_SIZE) {
> + dev_err(&chip->dev,
> + "Unexpected burstcnt: %zu (max=%zu, min=%d)\n",
> + burstcnt, buf_len, TPM_HEADER_SIZE);
> + rc = -EIO;
> + goto out_err;
> + }
> +
> + /* Read first chunk of burstcnt bytes */
> + rc = cr50_i2c_read(chip, addr, buf, burstcnt);
> + if (rc < 0) {
> + dev_err(&chip->dev, "Read of first chunk failed\n");
> + goto out_err;
> + }
> +
> + /* Determine expected data in the return buffer */
> + expected = be32_to_cpup((__be32 *)(buf + 2));
> + if (expected > buf_len) {
> + dev_err(&chip->dev, "Buffer too small to receive i2c data\n");
> + goto out_err;
> + }
> +
> + /* Now read the rest of the data */
> + cur = burstcnt;
> + while (cur < expected) {
> + /* Read updated burst count and check status */
> + rc = cr50_i2c_wait_burststs(chip, mask, &burstcnt, &status);
> + if (rc < 0)
> + goto out_err;
> +
> + len = min_t(size_t, burstcnt, expected - cur);
> + rc = cr50_i2c_read(chip, addr, buf + cur, len);
> + if (rc < 0) {
> + dev_err(&chip->dev, "Read failed\n");
> + goto out_err;
> + }
> +
> + cur += len;
> + }
> +
> + /* Ensure TPM is done reading data */
> + rc = cr50_i2c_wait_burststs(chip, TPM_STS_VALID, &burstcnt, &status);
> + if (rc < 0)
> + goto out_err;
> + if (status & TPM_STS_DATA_AVAIL) {
> + dev_err(&chip->dev, "Data still available\n");
> + rc = -EIO;
> + goto out_err;
> + }
> +
> + cr50_release_locality(chip, CR50_NO_FORCE);
> + return cur;
> +
> +out_err:
> + /* Abort current transaction if still pending */
> + if (cr50_i2c_tis_status(chip) & TPM_STS_COMMAND_READY)
> + cr50_i2c_tis_ready(chip);
> +
> + cr50_release_locality(chip, CR50_NO_FORCE);
> + return rc;
> +}
> +
> +/*
> + * cr50_i2c_tis_send - TPM emission callback
> + *
> + * @chip: TPM chip information
> + * @buf: buffer to send
> + * @len: buffer length
> + *
> + * Returns negative number for error, 0 for success.
> + */
> +static int cr50_i2c_tis_send(struct tpm_chip *chip, u8 *buf, size_t len)
> +{
> + struct priv_data *priv = dev_get_drvdata(&chip->dev);
> + int rc, status;
> + size_t burstcnt, limit, sent = 0;
> + u8 tpm_go[4] = { TPM_STS_GO };
> + unsigned long stop;
> +
> + rc = request_locality(chip);
> + if (rc < 0)
> + return rc;
> +
> + /* Wait until TPM is ready for a command */
> + stop = jiffies + chip->timeout_b;
> + while (!(cr50_i2c_tis_status(chip) & TPM_STS_COMMAND_READY)) {
> + if (time_after(jiffies, stop)) {
> + rc = -ETIMEDOUT;
> + goto out_err;
> + }
> +
> + cr50_i2c_tis_ready(chip);
> + }
> +
> + while (len > 0) {
> + u8 mask = TPM_STS_VALID;
> +
> + /* Wait for data if this is not the first chunk */
> + if (sent > 0)
> + mask |= TPM_STS_DATA_EXPECT;
> +
> + /* Read burst count and check status */
> + rc = cr50_i2c_wait_burststs(chip, mask, &burstcnt, &status);
> + if (rc < 0)
> + goto out_err;
> +
> + /*
> + * Use burstcnt - 1 to account for the address byte
> + * that is inserted by cr50_i2c_write()
> + */
> + limit = min_t(size_t, burstcnt - 1, len);
> + rc = cr50_i2c_write(chip, TPM_I2C_DATA_FIFO(priv->locality),
> + &buf[sent], limit);
> + if (rc < 0) {
> + dev_err(&chip->dev, "Write failed\n");
> + goto out_err;
> + }
> +
> + sent += limit;
> + len -= limit;
> + }
> +
> + /* Ensure TPM is not expecting more data */
> + rc = cr50_i2c_wait_burststs(chip, TPM_STS_VALID, &burstcnt, &status);
> + if (rc < 0)
> + goto out_err;
> + if (status & TPM_STS_DATA_EXPECT) {
> + dev_err(&chip->dev, "Data still expected\n");
> + rc = -EIO;
> + goto out_err;
> + }
> +
> + /* Start the TPM command */
> + rc = cr50_i2c_write(chip, TPM_I2C_STS(priv->locality), tpm_go,
> + sizeof(tpm_go));
> + if (rc < 0) {
> + dev_err(&chip->dev, "Start command failed\n");
> + goto out_err;
> + }
> + return 0;
> +
> +out_err:
> + /* Abort current transaction if still pending */
> + if (cr50_i2c_tis_status(chip) & TPM_STS_COMMAND_READY)
> + cr50_i2c_tis_ready(chip);
> +
> + cr50_release_locality(chip, CR50_NO_FORCE);
> + return rc;
> +}
> +
> +/*
> + * cr50_i2c_req_canceled - callback to notify a request cancel
> + *
> + * @chip: TPM chip information
> + * @status: status given by the cancel callback
> + *
> + * Return if command is ready or not
> + */
> +static bool cr50_i2c_req_canceled(struct tpm_chip *chip, u8 status)
> +{
> + return (status == TPM_STS_COMMAND_READY);
> +}
> +
> +static const struct tpm_class_ops cr50_i2c = {
> + .flags = TPM_OPS_AUTO_STARTUP,
> + .status = &cr50_i2c_tis_status,
> + .recv = &cr50_i2c_tis_recv,
> + .send = &cr50_i2c_tis_send,
> + .cancel = &cr50_i2c_tis_ready,
> + .req_complete_mask = TPM_STS_DATA_AVAIL | TPM_STS_VALID,
> + .req_complete_val = TPM_STS_DATA_AVAIL | TPM_STS_VALID,
> + .req_canceled = &cr50_i2c_req_canceled,
> +};
> +
> +static const struct i2c_device_id cr50_i2c_table[] = {
> + {"cr50_i2c", 0},
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, cr50_i2c_table);
> +
> +#ifdef CONFIG_ACPI
> +static const struct acpi_device_id cr50_i2c_acpi_id[] = {
> + { "GOOG0005", 0 },
> + {}
> +};
> +MODULE_DEVICE_TABLE(acpi, cr50_i2c_acpi_id);
> +#endif
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id of_cr50_i2c_match[] = {
> + { .compatible = "google,cr50", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, of_cr50_i2c_match);
> +#endif
> +
> +/*
> + * cr50_i2c_probe - driver prbe function
> + *
> + * @client: i2x client information
> + * @id: i2c device id
> + *
> + * Returns negative number for error, 0 for success.
> + */
> +static int cr50_i2c_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &client->dev;
> + struct tpm_chip *chip;
> + struct priv_data *priv;
> + u8 buf[4];
> + u32 vendor;
> + int rc;
> +
> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
> + return -ENODEV;
> +
> + chip = tpmm_chip_alloc(dev, &cr50_i2c);
> + if (IS_ERR(chip))
> + return PTR_ERR(chip);
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + /* cr50 is a TPM 2.0 chip */
> + chip->flags |= TPM_CHIP_FLAG_TPM2;
> + chip->flags |= TPM_CHIP_FLAG_FIRMWARE_POWER_MANAGED;
> +
> + /* Default timeouts */
> + chip->timeout_a = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->timeout_b = msecs_to_jiffies(TIS_LONG_TIMEOUT);
> + chip->timeout_c = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->timeout_d = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> +
> + dev_set_drvdata(&chip->dev, priv);
> + init_completion(&priv->tpm_ready);
> +
> + if (client->irq > 0) {
> + rc = devm_request_irq(dev, client->irq, cr50_i2c_int_handler,
> + IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> + dev->driver->name, chip);
> + if (rc < 0) {
> + dev_err(dev, "Failed to probe IRQ %d\n", client->irq);
> + return rc;
> + }
> +
> + disable_irq(client->irq);
> + priv->irq = client->irq;
> + } else {
> + dev_warn(dev, "No IRQ, will use %ums delay for TPM ready\n",
> + CR50_TIMEOUT_NOIRQ_MS);
> + }
> +
> + rc = request_locality(chip);
> + if (rc < 0) {
> + dev_err(dev, "Could not request locality\n");
> + return rc;
> + }
> +
> + /* Read four bytes from DID_VID register */
> + rc = cr50_i2c_read(chip, TPM_I2C_DID_VID(0), buf, sizeof(buf));
> + if (rc < 0) {
> + dev_err(dev, "Could not read vendor id\n");
> + cr50_release_locality(chip, CR50_FORCE);
> + return rc;
> + }
> +
> + vendor = le32_to_cpup((__le32 *)buf);
> + if (vendor != CR50_I2C_DID_VID) {
> + dev_err(dev, "Vendor ID did not match! ID was %08x\n", vendor);
> + cr50_release_locality(chip, CR50_FORCE);
> + return -ENODEV;
> + }
> +
> + dev_info(dev, "cr50 TPM 2.0 (i2c 0x%02x irq %d id 0x%x)\n",
> + client->addr, client->irq, vendor >> 16);
> +
> + return tpm_chip_register(chip);
> +}
> +
> +/*
> + * cr50_i2c_probe - driver prbe function
> + *
> + * @client: i2x client information
> + *
> + * Returns 0
> + */
> +static int cr50_i2c_remove(struct i2c_client *client)
> +{
> + struct tpm_chip *chip = i2c_get_clientdata(client);
> +
> + tpm_chip_unregister(chip);
> + cr50_release_locality(chip, CR50_FORCE);
> +
> + return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(cr50_i2c_pm, tpm_pm_suspend, tpm_pm_resume);
> +
> +static struct i2c_driver cr50_i2c_driver = {
> + .id_table = cr50_i2c_table,
> + .probe = cr50_i2c_probe,
> + .remove = cr50_i2c_remove,
> + .driver = {
> + .name = "cr50_i2c",
> + .pm = &cr50_i2c_pm,
> + .acpi_match_table = ACPI_PTR(cr50_i2c_acpi_id),
> + .of_match_table = of_match_ptr(of_cr50_i2c_match),
> + },
> +};
> +
> +module_i2c_driver(cr50_i2c_driver);
> +
> +MODULE_DESCRIPTION("cr50 TPM I2C Driver");
> +MODULE_LICENSE("GPL");
> --
> 2.29.2
>
>

I did not enumerate every possible style error but instead showed some
examples, because there were so many.

/Jarkko

\
 
 \ /
  Last update: 2020-11-23 23:09    [W:0.321 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site