lkml.org 
[lkml]   [2020]   [Nov]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next v3 12/12] net: dsa: microchip: ksz9477: add periodic output support
On Wed, Nov 18, 2020 at 09:30:13PM +0100, Christian Eggers wrote:
> The KSZ9563 has a Trigger Output Unit (TOU) which can be used to
> generate periodic signals.
>
> The pulse length can be altered via a device attribute.
>
> Tested on a Microchip KSZ9563 switch.
>
> Signed-off-by: Christian Eggers <ceggers@arri.de>
> ---
> drivers/net/dsa/microchip/ksz9477_ptp.c | 197 +++++++++++++++++++++++-
> drivers/net/dsa/microchip/ksz_common.h | 5 +
> 2 files changed, 201 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/dsa/microchip/ksz9477_ptp.c b/drivers/net/dsa/microchip/ksz9477_ptp.c
> index ce3fdc9a1f9e..3174574d52f6 100644
> --- a/drivers/net/dsa/microchip/ksz9477_ptp.c
> +++ b/drivers/net/dsa/microchip/ksz9477_ptp.c
> @@ -90,6 +90,20 @@ static int ksz9477_ptp_tou_cycle_count_set(struct ksz_device *dev, u16 count)
> return 0;
> }
>
> +static int ksz9477_ptp_tou_pulse_verify(u64 pulse_ns)
> +{
> + u32 data;
> +
> + if (pulse_ns & 0x3)
> + return -EINVAL;
> +
> + data = (pulse_ns / 8);
> + if (data != (data & TRIG_PULSE_WIDTH_M))
> + return -ERANGE;
> +
> + return 0;
> +}
> +
> static int ksz9477_ptp_tou_pulse_set(struct ksz_device *dev, u32 pulse_ns)
> {
> u32 data;
> @@ -196,6 +210,7 @@ static int ksz9477_ptp_adjfine(struct ptp_clock_info *ptp, long scaled_ppm)
> return ret;
> }
>
> +static int ksz9477_ptp_restart_perout(struct ksz_device *dev);
> static int ksz9477_ptp_enable_pps(struct ksz_device *dev, int on);
>
> static int ksz9477_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
> @@ -241,6 +256,15 @@ static int ksz9477_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
> case KSZ_PTP_TOU_IDLE:
> break;
>
> + case KSZ_PTP_TOU_PEROUT:
> + dev_info(dev->dev, "Restarting periodic output signal\n");

Isn't this a bit too verbose, or is there something for the user to be
concerned about?

> +
> + ret = ksz9477_ptp_restart_perout(dev);
> + if (ret)
> + goto error_return;
> +
> + break;
> +
> case KSZ_PTP_TOU_PPS:
> dev_info(dev->dev, "Restarting PPS\n");
>
> @@ -358,6 +382,15 @@ static int ksz9477_ptp_settime(struct ptp_clock_info *ptp,
> case KSZ_PTP_TOU_IDLE:
> break;
>
> + case KSZ_PTP_TOU_PEROUT:
> + dev_info(dev->dev, "Restarting periodic output signal\n");
> +
> + ret = ksz9477_ptp_restart_perout(dev);
> + if (ret)
> + goto error_return;
> +
> + break;
> +
> case KSZ_PTP_TOU_PPS:
> dev_info(dev->dev, "Restarting PPS\n");
>
> @@ -377,6 +410,159 @@ static int ksz9477_ptp_settime(struct ptp_clock_info *ptp,
> return ret;
> }
>
> +static int ksz9477_ptp_configure_perout(struct ksz_device *dev, u32 cycle_width_ns,

Watch out for 80 characters, please!

> + u16 cycle_count, u32 pulse_width_ns,
> + struct timespec64 const *target_time)
> +{
> + int ret;
> + u32 trig_ctrl;

Reverse Christmas tree.

> +
> + /* Enable notify, set rising edge, set periodic pattern */
> + trig_ctrl = TRIG_NOTIFY | (TRIG_POS_PERIOD << TRIG_PATTERN_S);
> + ret = ksz_write32(dev, REG_TRIG_CTRL__4, trig_ctrl);
> + if (ret)
> + return ret;
> +
> + ret = ksz9477_ptp_tou_cycle_width_set(dev, cycle_width_ns);
> + if (ret)
> + return ret;
> +
> + ksz9477_ptp_tou_cycle_count_set(dev, cycle_count);
> + if (ret)
> + return ret;
> +
> + ret = ksz9477_ptp_tou_pulse_set(dev, pulse_width_ns);
> + if (ret)
> + return ret;
> +
> + ret = ksz9477_ptp_tou_target_time_set(dev, target_time);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int ksz9477_ptp_enable_perout(struct ksz_device *dev,
> + struct ptp_perout_request const *perout_request, int on)
> +{
> + u32 gpio_stat0;
> + u64 cycle_width_ns;
> + int ret;
> +
> + if (dev->ptp_tou_mode != KSZ_PTP_TOU_PEROUT && dev->ptp_tou_mode != KSZ_PTP_TOU_IDLE)
> + return -EBUSY;
> +
> + ret = ksz9477_ptp_tou_reset(dev, 0);
> + if (ret)
> + return ret;
> +
> + if (!on) {
> + dev->ptp_tou_mode = KSZ_PTP_TOU_IDLE;
> + return 0; /* success */
> + }
> +
> + dev->ptp_perout_target_time_first.tv_sec = perout_request->start.sec;
> + dev->ptp_perout_target_time_first.tv_nsec = perout_request->start.nsec;
> +
> + dev->ptp_perout_period.tv_sec = perout_request->period.sec;
> + dev->ptp_perout_period.tv_nsec = perout_request->period.nsec;
> +
> + cycle_width_ns = timespec64_to_ns(&dev->ptp_perout_period);
> + if ((cycle_width_ns & GENMASK(31, 0)) != cycle_width_ns)
> + return -EINVAL;
> +
> + if (perout_request->flags & PTP_PEROUT_DUTY_CYCLE) {
> + u64 value = perout_request->on.sec * NSEC_PER_SEC +
> + perout_request->on.nsec;
> +
> + ret = ksz9477_ptp_tou_pulse_verify(value);
> + if (ret)
> + return ret;
> +
> + dev->ptp_perout_pulse_width_ns = value;
> + }

It is not guaranteed that user space will set this flag. Shouldn't you
assign a default value for the pulse width? I don't know, half the
period should be a good default.

Also, please reject PTP_PEROUT_ONE_SHOT and PTP_PEROUT_PHASE, since you
don't do anything with them, but user space might be led into believing
otherwise.

> +
> + ret = ksz9477_ptp_configure_perout(dev, cycle_width_ns,
> + dev->ptp_perout_cycle_count,
> + dev->ptp_perout_pulse_width_ns,
> + &dev->ptp_perout_target_time_first);
> + if (ret)
> + return ret;
> +
> + /* Activate trigger unit */
> + ret = ksz9477_ptp_tou_start(dev, NULL);
> + if (ret)
> + return ret;
> +
> + /* Check error flag:
> + * - the ACTIVE flag is NOT cleared an error!
> + */
> + ret = ksz_read32(dev, REG_PTP_TRIG_STATUS__4, &gpio_stat0);
> + if (ret)
> + return ret;
> +
> + if (gpio_stat0 & (1 << (0 + TRIG_ERROR_S))) {

What is the role of this "0 +" term here?

> + dev_err(dev->dev, "%s: Trigger unit0 error!\n", __func__);
> + ret = -EIO;
> + /* Unit will be reset on next access */
> + return ret;
> + }
> +
> + dev->ptp_tou_mode = KSZ_PTP_TOU_PEROUT;
> + return 0;
> +}

\
 
 \ /
  Last update: 2020-11-21 00:50    [W:0.150 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site