lkml.org 
[lkml]   [2020]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectAW: [PATCH] drm: imx: Move fbdev setup to before output polling
Date
Hi Thomas and Daniel,

Thank you very much for your feedback. We appreciate it.

> >>> diff --git a/drivers/gpu/drm/imx/imx-drm-core.c
> >>> b/drivers/gpu/drm/imx/imx-drm-core.c
> >>> index 9bf5ad6d18a2..2665040e11c7 100644
> >>> --- a/drivers/gpu/drm/imx/imx-drm-core.c
> >>> +++ b/drivers/gpu/drm/imx/imx-drm-core.c
> >>> @@ -240,14 +240,18 @@ static int imx_drm_bind(struct device *dev)
> >>> legacyfb_depth = 16;
> >>> }
> >>>
> >>> + /*
> >>> + * The generic fbdev has to be setup before enabling output polling.
> >>> + * Otherwise the fbdev client is not ready to handle delayed events.
> >>> + */
> >>> + drm_fbdev_generic_setup(drm, legacyfb_depth);
> >>> +
> >>> drm_kms_helper_poll_init(drm);
> >>>
> >>> ret = drm_dev_register(drm, 0);
> >>> if (ret)
> >>> goto err_poll_fini;
> >>>
> >>> - drm_fbdev_generic_setup(drm, legacyfb_depth);
> >>> -
> >>
> >> This does not work well. fbdev is supposed to be another regular DRM
> >> client. It has to be enabled after registering the DRM device.
> >>
> >> I'd rather improve fbdev or the driver to handle this gracefully.
> >
> > Yeah I'm not understanding the point here. Once fbcon is running, you
> > have a screen. Any fbdev userspace client also should do a modeset
> > first. And if they dont and it's expected uapi for fbdev chardev that
> > the display boots up enabled, then we need to fix that in the fbdev
> > helpers, not through clever reordering in drivers so that a
> > side-effect causes a modeset.
> >
> > Note that this is a bit tricky since fbdev shouldn't take over the
> > screen by default, so we'd need to delay this until first open of
> > /dev/fb0. And we should probably also delay the hotplug handling until
> > the first open. fbcon also fake-opens the fbdev file, so it's the same
> > code path.
>
> As far as I understand the commit message, the problem is that the display
> blanks out after registering the driver. And fbdev somewhat mitigates this by
> doing an early modeset. Users with fbdev disabled (most of them in
> embedded, I guess) would still run into the issue until userspace makes a
> modeset.
>
> Mark, if that's the case, an option might be to pick up the device settings
> instead of calling drm_mode_config_reset(). The driver would then continue
> to display whatever is on the screen.

We are started using fbdev in our embedded application with Linux 3.10, later
updated to 4.14 and are now in the process of updating to 5.4. So far the uapi
appeared to us as if we could rely on an already enabled fbdev. That is, none
of our applications does a modeset.

When switching to 5.4 we noticed that the fbdev uapi changed. That is, the
LCD is switched off until it is explicitly enabled. It could be enabled by
writing to /sys/class/graphics/fb0/blank.

You are right, we are not using fbcon. fbcon will still enable the LCD but in our
embedded domain we have it disabled because we must not show a console.

Do we understand your proposal correctly to replace the call to
drm_mode_config_reset() in imx_drm_bind() [imx-drm-core.c] with picking up
the device settings instead?

https://elixir.bootlin.com/linux/v5.10-rc4/source/drivers/gpu/drm/imx/imx-drm-core.c#L231

We are a little clueless right now: How do we pick up the device settings?

Greetings,
Mark
\
 
 \ /
  Last update: 2020-11-18 10:49    [W:0.070 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site