lkml.org 
[lkml]   [2020]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 3/6] remoteproc/pru: Add support for PRU specific interrupt configuration
From
Date
Hi Greg,

On 11/14/20 2:46 AM, Grzegorz Jaszczyk wrote:
> The firmware blob can contain optional ELF sections: .resource_table
> section and .pru_irq_map one. The second one contains the PRUSS
> interrupt mapping description, which needs to be setup before powering
> on the PRU core. To avoid RAM wastage this ELF section is not mapped to
> any ELF segment (by the firmware linker) and therefore is not loaded to
> PRU memory.
>
> The PRU interrupt configuration is handled within the PRUSS INTC irqchip
> driver and leverages the system events to interrupt channels and host
> interrupts mapping configuration. Relevant irq routing information is
> passed through a special .pru_irq_map ELF section (for interrupts routed
> to and used by PRU cores) or via the PRU application's device tree node
> (for interrupts routed to and used by the main CPU). The mappings are
> currently programmed during the booting/shutdown of the PRU.
>
> The interrupt configuration passed through .pru_irq_map ELF section is
> optional. It varies on specific firmware functionality and therefore
> have to be unwinded during PRU stop and performed again during
> PRU start.
>
> Co-developed-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
> ---
> drivers/remoteproc/pru_rproc.c | 191 ++++++++++++++++++++++++++++++++-
> drivers/remoteproc/pru_rproc.h | 46 ++++++++
> 2 files changed, 236 insertions(+), 1 deletion(-)
> create mode 100644 drivers/remoteproc/pru_rproc.h
>
> diff --git a/drivers/remoteproc/pru_rproc.c b/drivers/remoteproc/pru_rproc.c
> index c94c8e965c21..825e9c7e081b 100644
> --- a/drivers/remoteproc/pru_rproc.c
> +++ b/drivers/remoteproc/pru_rproc.c
> @@ -11,13 +11,16 @@
> */
>
> #include <linux/bitops.h>
> +#include <linux/irqdomain.h>
> #include <linux/module.h>
> #include <linux/of_device.h>
> +#include <linux/of_irq.h>
> #include <linux/pruss_driver.h>
> #include <linux/remoteproc.h>
>
> #include "remoteproc_internal.h"
> #include "remoteproc_elf_helpers.h"
> +#include "pru_rproc.h"
>
> /* PRU_ICSS_PRU_CTRL registers */
> #define PRU_CTRL_CTRL 0x0000
> @@ -41,6 +44,8 @@
> #define PRU_SDRAM_DA 0x2000 /* Secondary Data RAM */
> #define PRU_SHRDRAM_DA 0x10000 /* Shared Data RAM */
>
> +#define MAX_PRU_SYS_EVENTS 160
> +
> /**
> * enum pru_iomem - PRU core memory/register range identifiers
> *
> @@ -64,6 +69,10 @@ enum pru_iomem {
> * @rproc: remoteproc pointer for this PRU core
> * @mem_regions: data for each of the PRU memory regions
> * @fw_name: name of firmware image used during loading
> + * @mapped_irq: virtual interrupt numbers of created fw specific mapping
> + * @pru_interrupt_map: pointer to interrupt mapping description (firmware)
> + * @pru_interrupt_map_sz: pru_interrupt_map size
> + * @evt_count: number of mapped events
> */
> struct pru_rproc {
> int id;
> @@ -72,6 +81,10 @@ struct pru_rproc {
> struct rproc *rproc;
> struct pruss_mem_region mem_regions[PRU_IOMEM_MAX];
> const char *fw_name;
> + int *mapped_irq;
> + struct pru_irq_rsc *pru_interrupt_map;
> + size_t pru_interrupt_map_sz;
> + ssize_t evt_count;

Do you really need this to be ssize_t type?

> };
>
> static inline u32 pru_control_read_reg(struct pru_rproc *pru, unsigned int reg)
> @@ -85,15 +98,107 @@ void pru_control_write_reg(struct pru_rproc *pru, unsigned int reg, u32 val)
> writel_relaxed(val, pru->mem_regions[PRU_IOMEM_CTRL].va + reg);
> }
>
> +static void pru_dispose_irq_mapping(struct pru_rproc *pru)
> +{
> + while (--pru->evt_count >= 0) {
> + if (pru->mapped_irq[pru->evt_count] > 0)
> + irq_dispose_mapping(pru->mapped_irq[pru->evt_count]);
> + }
> +
> + kfree(pru->mapped_irq);
> +}
> +
> +/*
> + * Parse the custom PRU interrupt map resource and configure the INTC
> + * appropriately.
> + */
> +static int pru_handle_intrmap(struct rproc *rproc)
> +{
> + struct device *dev = rproc->dev.parent;
> + struct pru_rproc *pru = rproc->priv;
> + struct pru_irq_rsc *rsc = pru->pru_interrupt_map;
> + struct irq_fwspec fwspec;
> + struct device_node *irq_parent;
> + int i, ret = 0;
> +
> + /* not having pru_interrupt_map is not an error */
> + if (!rsc)
> + return 0;
> +
> + /* currently supporting only type 0 */
> + if (rsc->type != 0) {
> + dev_err(dev, "unsupported rsc type: %d\n", rsc->type);
> + return -EINVAL;
> + }
> +
> + if (rsc->num_evts < 0 || rsc->num_evts > MAX_PRU_SYS_EVENTS)
> + return -EINVAL;
> +
> + if (sizeof(*rsc) + rsc->num_evts * sizeof(struct pruss_int_map) !=
> + pru->pru_interrupt_map_sz)
> + return -EINVAL;
> +
> + pru->evt_count = rsc->num_evts;
> + pru->mapped_irq = kcalloc(pru->evt_count, sizeof(int), GFP_KERNEL);
> + if (!pru->mapped_irq)
> + return -ENOMEM;
> +
> + /*
> + * parse and fill in system event to interrupt channel and
> + * channel-to-host mapping
> + */
> + irq_parent = of_irq_find_parent(pru->dev->of_node);
> + if (!irq_parent) {
> + kfree(pru->mapped_irq);
> + return -ENODEV;
> + }
> +
> + fwspec.fwnode = of_node_to_fwnode(irq_parent);
> + fwspec.param_count = 3;
> + for (i = 0; i < pru->evt_count; i++) {
> + fwspec.param[0] = rsc->pru_intc_map[i].event;
> + fwspec.param[1] = rsc->pru_intc_map[i].chnl;
> + fwspec.param[2] = rsc->pru_intc_map[i].host;
> +
> + dev_dbg(dev, "mapping%d: event %d, chnl %d, host %d\n",
> + i, fwspec.param[0], fwspec.param[1], fwspec.param[2]);
> +
> + pru->mapped_irq[i] = irq_create_fwspec_mapping(&fwspec);
> + if (pru->mapped_irq[i] < 0) {
> + dev_err(dev, "failed to get virq\n");
> + ret = pru->mapped_irq[i];
> + goto map_fail;
> + }
> + }
> +
> + return ret;
> +
> +map_fail:
> + pru_dispose_irq_mapping(pru);
> +
> + return ret;
> +}
> +
> static int pru_rproc_start(struct rproc *rproc)
> {
> struct device *dev = &rproc->dev;
> struct pru_rproc *pru = rproc->priv;
> u32 val;
> + int ret;
>
> dev_dbg(dev, "starting PRU%d: entry-point = 0x%llx\n",
> pru->id, (rproc->bootaddr >> 2));
>
> + ret = pru_handle_intrmap(rproc);
> + /*
> + * reset references to pru interrupt map - they will stop being valid
> + * after rproc_start returns
> + */
> + pru->pru_interrupt_map = NULL;
> + pru->pru_interrupt_map_sz = 0;
> + if (ret)
> + return ret;
> +
> val = CTRL_CTRL_EN | ((rproc->bootaddr >> 2) << 16);
> pru_control_write_reg(pru, PRU_CTRL_CTRL, val);
>
> @@ -112,6 +217,10 @@ static int pru_rproc_stop(struct rproc *rproc)
> val &= ~CTRL_CTRL_EN;
> pru_control_write_reg(pru, PRU_CTRL_CTRL, val);
>
> + /* dispose irq mapping - new firmware can provide new mapping */
> + if (pru->mapped_irq)
> + pru_dispose_irq_mapping(pru);
> +
> return 0;
> }
>
> @@ -274,16 +383,96 @@ pru_rproc_load_elf_segments(struct rproc *rproc, const struct firmware *fw)
> return ret;
> }
>
> +static const void *
> +pru_rproc_find_interrupt_map(struct device *dev, const struct firmware *fw)
> +{
> + const void *shdr, *name_table_shdr;
> + const char *name_table;
> + const u8 *elf_data = (void *)fw->data;
> + u8 class = fw_elf_get_class(fw);
> + size_t fw_size = fw->size;
> + const void *ehdr = elf_data;
> + u16 shnum = elf_hdr_get_e_shnum(class, ehdr);
> + u32 elf_shdr_get_size = elf_size_of_shdr(class);
> + u16 shstrndx = elf_hdr_get_e_shstrndx(class, ehdr);
> + int i;
> +
> + /* first, get the section header according to the elf class */
> + shdr = elf_data + elf_hdr_get_e_shoff(class, ehdr);
> + /* compute name table section header entry in shdr array */
> + name_table_shdr = shdr + (shstrndx * elf_shdr_get_size);
> + /* finally, compute the name table section address in elf */
> + name_table = elf_data + elf_shdr_get_sh_offset(class, name_table_shdr);

I see you used the style influenced by the remoteproc_elf_loader code. PRUs are
all 32-bit, so we need not use this strictly. I am ok with this style, but
prefer consistent usage style between this function and
pru_rproc_load_elf_segments().

> +
> + for (i = 0; i < shnum; i++, shdr += elf_shdr_get_size) {
> + u64 size = elf_shdr_get_sh_size(class, shdr);
> + u64 offset = elf_shdr_get_sh_offset(class, shdr);
> + u32 name = elf_shdr_get_sh_name(class, shdr);
> +
> + if (strcmp(name_table + name, ".pru_irq_map"))
> + continue;
> +
> + /* make sure we have the entire table */
> + if (offset + size > fw_size || offset + size < size) {
> + dev_err(dev, "interrupt map sec truncated\n");

sec can confuse developers, suggest rephrasing this trace, something like
".pru_irq_map section truncated"

> + return ERR_PTR(-EINVAL);
> + }
> +
> + /* make sure table has at least the header */
> + if (sizeof(struct pru_irq_rsc) > size) {
> + dev_err(dev, "header-less interrupt map sec\n");

same comment as above

> + return ERR_PTR(-EINVAL);
> + }
> +
> + return shdr;
> + }
> +
> + dev_dbg(dev, "no .pru_irq_map section found for this fw\n");
> +
> + return NULL;
> +}
> +
> +/*
> + * Usa a custom parse_fw callback function for dealing with standard
> + * resource table and a PRU-specific custom ELF section.
> + *
> + * The firmware blob can contain optional ELF sections: .resource_table section
> + * and .pru_irq_map one. The second one contains the PRUSS interrupt mapping
> + * description, which needs to be setup before powering on the PRU core. To
> + * avoid RAM wastage this ELF section is not mapped to any ELF segment (by the
> + * firmware linker) and therefore is not loaded to PRU memory.

Some of this description can move to Patch 2 as well.

> + */
> static int pru_rproc_parse_fw(struct rproc *rproc, const struct firmware *fw)
> {
> + struct device *dev = &rproc->dev;
> + struct pru_rproc *pru = rproc->priv;
> + const u8 *elf_data = fw->data;
> + const void *shdr;
> + u8 class = fw_elf_get_class(fw);
> + u64 sh_offset;
> int ret;
>
> /* load optional rsc table */
> ret = rproc_elf_load_rsc_table(rproc, fw);
> if (ret == -EINVAL)
> dev_dbg(&rproc->dev, "no resource table found for this fw\n");
> + else if (ret)
> + return ret;

This hunk should be part of Patch 2.

>
> - return ret;
> + /* find .pru_interrupt_map section, not having it is not an error */
> + shdr = pru_rproc_find_interrupt_map(dev, fw);
> + if (IS_ERR(shdr))
> + return PTR_ERR(shdr);
> +
> + if (!shdr)
> + return 0;
> +
> + /* preserve pointer to PRU interrupt map together with it size */
> + sh_offset = elf_shdr_get_sh_offset(class, shdr);
> + pru->pru_interrupt_map = (struct pru_irq_rsc *)(elf_data + sh_offset);
> + pru->pru_interrupt_map_sz = elf_shdr_get_sh_size(class, shdr);
> +
> + return 0;

And this one as well.

regards
Suman

> }
>
> /*
> diff --git a/drivers/remoteproc/pru_rproc.h b/drivers/remoteproc/pru_rproc.h
> new file mode 100644
> index 000000000000..8ee9c3171610
> --- /dev/null
> +++ b/drivers/remoteproc/pru_rproc.h
> @@ -0,0 +1,46 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */
> +/*
> + * PRUSS Remote Processor specific types
> + *
> + * Copyright (C) 2014-2020 Texas Instruments Incorporated - https://www.ti.com/
> + * Suman Anna <s-anna@ti.com>
> + */
> +
> +#ifndef _PRU_RPROC_H_
> +#define _PRU_RPROC_H_
> +
> +/**
> + * struct pruss_int_map - PRU system events _to_ channel and host mapping
> + * @event: number of the system event
> + * @chnl: channel number assigned to a given @event
> + * @host: host number assigned to a given @chnl
> + *
> + * PRU system events are mapped to channels, and these channels are mapped
> + * to host interrupts. Events can be mapped to channels in a one-to-one or
> + * many-to-one ratio (multiple events per channel), and channels can be
> + * mapped to host interrupts in a one-to-one or many-to-one ratio (multiple
> + * channels per interrupt).
> + */
> +struct pruss_int_map {
> + u8 event;
> + u8 chnl;
> + u8 host;
> +};
> +
> +/**
> + * struct pru_irq_rsc - PRU firmware section header for IRQ data
> + * @type: resource type
> + * @num_evts: number of described events
> + * @pru_intc_map: PRU interrupt routing description
> + *
> + * The PRU firmware blob can contain optional .pru_irq_map ELF section, which
> + * provides the PRUSS interrupt mapping description. The pru_irq_rsc struct
> + * describes resource entry format.
> + */
> +struct pru_irq_rsc {
> + u8 type;
> + u8 num_evts;
> + struct pruss_int_map pru_intc_map[];
> +} __packed;
> +
> +#endif /* _PRU_RPROC_H_ */
>

\
 
 \ /
  Last update: 2020-11-17 21:43    [W:0.600 / U:0.408 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site